American Standard 2903.XXXW User Manual

SAVONA OVAL™

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

241 mm

(9-1/2)

SEE FTTG.SPECS

FOR DIMENSION

OF SUPPLIES

305mm(12) X 229?mm(9)

1073mm

(42-1/4)

537mm

(21-1/8)

76mm

(3)

OF DRAIN

OUTLET

95mm

(3-3/4)

51mm

(2)

540mm

(21-1/4 )

489mm

(19-1/4)

SAFE-T-HEATER REMOVABLE BLANK

305mm

(12)

102mm (4)

1-1/2 N.P.T.M.

THREADS

1-1/2 O.D.

TAILPIECE

GENERAL SPECIFICATIONS FOR 2903 WHIRLPOOL

INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW WHIRLPOOL MIN. OPERATING VOL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT3)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

CUTOUT IN FLOOR FOR DRAIN

C/L OF

VALV ES

60 x 42-1/4 x 21-1/4 In.(1524 x 1073 x 540mm)

2903.XXXW SERIES WHIRLPOOL/BATHING POOL

INSTALLATION INSTRUCTIONS

1524mm

(60)

ON/OFF

SWITCH

SHOWER ARM

C/L OF SPOUT

35mm

(1-3/8)

45 x 23 In. (1143 x 584mm) 53 x 32 In. (1346 x 813mm)

35 Lbs./Sq.Ft. (166 Kgs./Sq.m)

▲OUTLINE OF CUTOUT - USE TEMPLATE

C/L OF

INTEGRAL FEET SUPPORT

ROUGH FLOOR

98mm (3-7/8)

107 Lbs. (49 Kg.)

640 Lbs. (291 Kg.)

64 Gal. (243 L) 53 Gal. (201 L)

15 In. (381mm)

1.6 HP, 9.7 AMPS, 120V.SYSTEM I PUMP

PROVIDE ACCESS

SERVICING ON ALL

INSTALLATIONS

TO PUMP FOR

1651-1981mm

(65-78)

OPTIONAL

27.8

45.4

PUMP (MAY EXTEND BEYOND RIM BY 1-1/2")

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool. To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

• Safe-T-Heater 9075.120*

 List of Required Components (not included):

• Drain 1583.470* • Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 1 x 3 or 2 x 2 Stringers

• Drop Cloth

• 15 amp GFI Outlet

• Cement, Plaster, Grout

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks. If a whirlpool, do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system. Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

752878-100 Rev. E

FRAMING AND INSTALLATION

The variety of installations possible for this bath may require framing procedures other than those shown.

Locate studs as required. Insure rough dimensions are proper, plumb and square.

For whirlpools, provision must be made in all installations for an access opening for servicing pump and controls.

The following procedure must be used for all installations: stringer or pier height should be as indicated. The sump of the bath is supported by integral feet and no additional sump support is required. Once the bath is in place, the feet should be shimmed accordingly, so that the rim of the bath contacts the stringer or pier but supports no weight. Any finish material, such as tile or wall board, must be self-supporting if it contacts the rim of the bath.

SUGGESTED INSTALLATION METHOD

LEVELING SURFACE

WATERPROOF SEALANT

BATH

TYPICAL INSTALLATION

SEE

AS DESIRED

19-1/4

(489mm)

AS DESIRED

IT MAY BE NECESSARY TO NOTCH DECK SURFACE, AS PUMP MAY PROJECT BEYOND RIM OF BATH BY 1-1/2".

UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610 mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

CUTOUT TEMPLATE PROVIDED

IT MAY BE NECESSARY TO NOTCH DECK SURFACE TO ACCOMMODATE WHIRLPOOL ON/OFF SWITCH DURING INSTALLATION

(305 mm)

(610mm)

ACCESS PANEL

752878-100 Rev. E (2)

SPIC AND SPAN® IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE

+ 2 hidden pages