American Standard 2903.018W User Manual

SAVONA OVAL™ WHIRLPOOL

HIGH GLOSS ACRYLIC

SAVONA OVAL™ WHIRLPOOL

❏ 2903.018W Whirlpool

• Acrylic with fiberglass reinforcement

• Pre-leveled tub bottom

• Dual, molded-in arm rests

• 1.5 HP, single speed, self-draining pump/motor

• Factory installed power cord and plug

• Eight multi-directional and flow-adjustable jets including:

- Two foot jets

- Four body massage jets

- Two recessed back-rest jets

• Deck-mounted air switch On/Off

• Two silent air volume controls

• Quick Connect Safe-T-Heater connection system

• Factory installed and tested whirlpool system

❏ 2903.018WC StayClean™ Whirlpool

Massage featuring System I

• Same as 2903.018W except with the StayClean™ whirlpool system featuring Antimicrobial AlphaSan®

❏ 2903.002 Bathtub only

Nominal Dimensions: 60 x 42-1/4 x 21-1/4 (1524 x 1073 x 540mm)

BV-8

Rev. 9/05

NOTE: Roughing-in dimensions and product specifications shown on reverse side of page.

Compliance Certifications Meets or Exceeds the Following Specifications:

• Underwriters Laboratories - Hydromassage Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

To Be Specified - Required:

❏ Color: (specify color)

❏ Bath Faucet (specify finish)

❏ Rotary Drain: 1583.470 (specify finish)

To Be Specified - Optional:

❏ Safe-T-Heater*: 9075.120

❏ Jet Trim Ring Kit: 9860.200-two per kit

(specify finish) for Body Massage Jets only

For color/finish availability and other faucet choices, please see the Product Selector and Pricing Guide.

* NOTE: the Safe-T-Heater is designed to maintain water temperature during operation. It will not heat cold water to desired bathing temperature.

SAVONA OVAL™ WHIRLPOOL

HIGH GLOSS ACRYLIC

SEE FTTG.SPECS

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.

IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.

OPTIONAL TILING BEAD KIT AVAILABLE.

REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF (152mm) 6 ABOVE ROUGH FLOOR.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 / CSA Certified.

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

■

●

FOR DIMENSION

OF SUPPLIES

1073mm (42-1/4)

537mm (21-1/8)

95mm

(3-3/4)

51mm

(2)

540mm

(21-1/4 )

489mm

(19-1/4)

SAFE-T-HEATER REMOVABLE BLANK

76mm

305mm

(12)

(3)

OF DRAIN

OUTLET

VALVE S

102mm (4)

1-1/2 N.P.T.M.

THREADS

1-1/2 O.D.

TAILPIECE

241 mm

(9-1/2)

305mm(12) X 229?mm(9) CUTOUT IN FLOOR FOR DRAIN

C/L OF

1524mm

C/L OF SPOUT

(1-3/8)

(60)

ON/OFF

SWITCH

SHOWER ARM

35mm

C/L OF

INTEGRAL FEET SUPPORT

ROUGH FLOOR

98mm (3-7/8)

▲OUTLINE OF CUTOUT - USE TEMPLATE

PROVIDE ACCESS

TO PUMP FOR

SERVICING ON ALL

INSTALLATIONS

1651-1981mm

(65-78)

OPTIONAL

PUMP (MAY EXTEND BEYOND RIM BY 1-1/2")

1524mm

(60)

C/L OF SPOUT

35mm

(1-3/8)

C/L OF

SHOWER ARM

INTEGRAL FEET SUPPORT

98mm (3-7/8)

▲OUTLINE OF CUTOUT - USE TEMPLATE

ROUGH FLOOR

SEE FTTG.SPECS

FOR DIMENSION

OF SUPPLIES

1073mm

(42-1/4)

537mm

(21-1/8)

76mm

95mm

(3-3/4)

51mm

(2)

540mm

(21-1/4 )

489mm

(19-1/4)

(3)

305mm

(12)

OF DRAIN

OUTLET

VALV ES

102mm (4)

1-1/2 N.P.T.M.

THREADS

1-1/2 O.D.

TAILPIECE

241 mm

(9-1/2)

305mm(12) X 229?mm(9) CUTOUT IN FLOOR FOR DRAIN

C/L OF

1651-1981mm

(65-78)

OPTIONAL

GENERAL SPECIFICATIONS FOR 2903 WHIRLPOOL

INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW WHIRLPOOL MIN. OPERATING VOL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT3)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

60 x 42-1/4 x 21-1/4 In.(1524 x 1073 x 540mm)

35 Lbs./Sq.Ft. (166 Kgs./Sq.m)

107 Lbs. (49 Kg.)

640 Lbs. (291 Kg.)

64 Gal. (243 L)

45 x 23 In. (1143 x 584mm) 53 x 32 In. (1346 x 813mm)

53 Gal. (201 L)

15 In. (381mm)

27.8

45.4

GENERAL SPECIFICATIONS FOR 2903 BATHING POOL

INSTALLED SIZE

WEIGHT WEIGHT w/WATER BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT3)

60 x 42-1/4 x 21-1/4 In.

(1524 x 1073 x 540mm)

45 x 23 In. (1143 x 584mm) 53 x 32 In. (1346 x 813mm)

35 Lbs./Sq.Ft. (166 Kgs./Sq.m)

1.6 HP, 9.7 AMPS, 120V.SYSTEM I PUMP

107 Lbs. (49 Kg.)

640 Lbs. (291 Kg.)

15 In. (381mm)

27.8

45.4