American Standard 2901EC User Manual
SAV ONA ELITE™ 6’
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
SAVONA ELITE™ 6’ WHIRLPOOL
Comfortable two person design with generous
back support positions andf molded-in armrests
❏ 2901E (specify White 020, Bone 021, or
Linen 222)
• Acrylic with fiberglass reinforcement
• 2.0 HP self-draining pump/motor
with dry run seal
• Ten multi-directional and flow adjustable
jets including:
Two high performance Ideal-flow™ Jets
Eight interchangeable Flex-jets™
• Three silent air volume controls
• Deck-mounted On/Off control
• Complete factory installed and tested
whirlpool system
❏ 2901EC (specify White 020, Bone 021, or
Linen 222)
• Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 71-1/4” x 43-1/2” x 22"
(1810 x 1105 x 559mm)
© 2003 American Standard Inc.
HD-005
Revised 10/03
SPS 2901E
Components Needed:
❏ Bath Filler*: (specify finish)
❏ Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏ Pulse Jet Kit: PULSE-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏ Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100
❏ Tile Bead Kit: TILE-BEAD
NOTE: Roughing-in dimensions and product specifications shown on reverse side of page.
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See American Standard Faucet Selector
NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.
SAV ONA ELITE™ 6’
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS
SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING
AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.
OPTIONAL TILING BEAD KIT No. TILE-BEAD AVAILABLE AND MUST BE ORDERED SEPARATELY.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 / CSA Certified.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.
■
●
1105mm
(43-1/2)
305mm
(12)
C/L OF 1-1/2 O.D.
DRAIN OUTLET
51mm
(2)
552mm
(21-3/4)
140mm
(5-1/2)
INTEGRAL
905mm
(35-5/8)
●
RECOMMENDED
FITTING LOCATION
64 X 279mm (2-1/2 X 11)
38mm
(1-1/2)
FEET
44 mm
(1-3/4)
1-1/2 O.D. TAILPIECE
C/L
229mm X 305mm
(9 X 12) FLOOR
C/L OF OVERFLOW
89mm
(3-1/2)
89 mm
(3-1/2)
1810mm
(71-1/4)
IN-LINE HEATER
REMOVABLE
BLANK
178mm
(7)
CUTOUT
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
■ LEVELING STRINGER
NOT FOR SUPPORT
1-1/2 N.P.T.M.
THREADS
19mm
(3/4)
TYP.
PUMP
ON/OFF
SWITCH
508mm
(20)
ROUGH
FLOOR
OUTLINE OF
1772mm X
1067mm
(69-3/4 X 42)
CUTOUT
559mm
(22)
GENERAL SPECIFICATIONS FOR 2901E WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
71-1/4 x 43-1/2 x 22 In.(1810 x 1105 x 559mm)
152 Lbs. (68 Kg.)
67-1/2 x 33 In. (1715 x 838mm)
43 Lbs./Sq.Ft. (211 Kgs./Sq.m)
936 Lbs. (421 Kg.)
94 Gal. (356 L)
44 x 28 In. (1118 x 711mm)
2.1 HP, 14.4 AMPS, 120V.PUMP
86 Gal.(326 L)
16-1/4 In. (413mm)
27.8
61.5
Loading...