American Standard 2901.028WC, 9861.100 User Manual
SAVONA™ WHIRLPOOL
❏ 2901.028WC Whirlpool featuring System II
• Acrylic with berglass reinforcement
• EverClean® System
• Pre-leveled tub bottom
• Two person design with center drain and dual
lumbar ends
• Dual, molded-in arm rests
• Faucet deck/accessory area
• 2.1 HP two speed, self-draining pump/motor
with pulse feature
• Factory installed power cord with plug
• Ten multi-directional and ow-adjustable
jets including:
- Two Ideal-ow jets
- Six body massage jets
- Two recessed back-rest jets
• Deck-mounted, electronic control with 20
minute built-in timed safety shut off and
Chrome bezel
• Three silent air volume controls
• Quick Connect Safe-T-Heater
connection system
• Factory installed and tested whirlpool system
SAVONA™
WHIRLPOOL
HIGH GLOSS
Nominal Dimensions:
1810 x 1105 x 559mm
(71-1/4" x 43-1/2" x 22")
Compliance Certications Meets or Exceeds the Following Specications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
American Standard whirlpools and air baths with
EverClean® incorporate a patented silver-ion
additive right into the circulation piping to protect
the pipes from mold, mildew, algae and fungus that
could cause deterioration or staining of the pipes.
SEE REVERSE FOR PRODUCT DIMENSIONS
AND SPECIFICATIONS
To Be Specied - Required:
❏ Color: (specify color)
❏ Bath Faucet: (specify nish)
❏ Rotary Drain: 1583.470 (specify nish)
To Be Specied - Optional:
❏ Safe-T-Heater*: 9075.120
❏ System II Control Bezel: 9861.100 (specify nish)
For color/nish availability and other faucet choices, please
see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
© 2008 AS America Inc.
H35
Revised 2/08
SAVONA™
ON/OFF
SWITCH
181 0m m
(71 -1 /4)
905 mm
(35 -5 /8)
C/L
19m m
(3/ 4)
TYP .
110 5m m
(43 -1 /2)
552 mm
(21 -3 /4)
305 mm
(12 )
140 mm
(5- 1/ 2)
508 mm
(20 )
559 mm
(22 )
178 mm
(7)
OUTLINE OF
1772mm X
1067mm
(69-3/4 X 42)
CUTOUT
PUMP
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
229mm X 305mm
(9 X 12) FLOOR
CUTOUT
RECOMMENDED
FITTING LOCATION
64 X 279mm (2-1/2 X 11)
C/L OF 1-1/2 O.D.
DRAIN OUTLET
C/L OF OVERFLOW
51mm
(2)
38mm
(1-1/2)
89mm
(3-1/2)
LEVELING STRINGER
NOT FOR SUPPORT
ROUGH
FLOOR
1-1/2 O.D. TAILPIECE
INTEGRAL
FEET
89 mm
(3-1/2)
44 mm
(1-3/4)
1-1/2 N.P.T.M.
THREADS
SAFE-T-HEATER
REMOVABLE
BLANK
GENERA L SPECI FICATI ONS FO R 2901 WHIRLP OOL
71- 1/ 4 x 43 -1 /2 x 22 I n. (1 81 0 x 1105 x 55 9m m)
1 52 L bs . (6 8 Kg.)
936 L bs . (4 21 K g.)
94 Ga l. ( 35 6 L)
86 Ga l. (3 26 L )
44 x 28 I n. ( 11 18 x 71 1m m)
67- 1/ 2 x 33 I n. (171 5 x 83 8m m)
16- 1/ 4 In . (4 13 mm)
43 Lb s. /S q. Ft . (211 Kg s. /S q. m)
27. 8
61. 5
INS TA LL ED S IZ E
WEI GH T
WEI GH T w/ WA TE R
GAL . TO O VE RF LO W
WHI RL PO OL M IN . OPERA TI NG V OL .
BAT HI NG W EL L AT SUMP
BAT HI NG W EL L AT RIM
WAT ER D EP TH T O OVERF LO W
FLO OR L OA DI NG
(PR OJ EC TE D AR EA )
PTS .
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
2.1 H P, 1 5. 6 AM PS, 1 20 V.SYS TE M II P UM P
WHIRLPOOL
HIGH GLOSS
© 2008 AS America Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA T YPE INSTALLATION. SUMP
OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.
OPTIONAL TILING BE AD KIT AVAILABLE.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
ON SYSTEM I I: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF (152mm) 6 ABOVE ROUGH FLOOR.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 / CSA
Certied. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.
H36
Revised 2/08
Loading...