American Standard 2471 User Manual
Installation
Instructions
THE
COLLECTION
by
™
CenterSet Faucet
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read
these instructions carefully before you begin.
TOOLS REQUIRED
2471
Certified to comply with ASME A112.18.1M
Certifié ASME A112.18.1M
M968286
INSTALL FAUCET
1
CAUTION
Turn off hot and cold water supplies before beginning.
Apply a bead of PUTTY along the edge of the
underside of the BODY (1). Insert LIFT ROD (2)
through hole in BODY (1).
Insert faucet SHANKS through holes of SINK. Place
faucet as far forward as possible.
2
Basin Wrench
SECURE FAUCET AND MAKE WATER
2
SUPPLY CONNECTIONS
Secure FAUCET (1) with ATTACHMENT NUTS (2) supplied.
(HAND TIGHTEN).
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (3) or 3/8" O.D. BULL-NOSE RISERS (4). Use
adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
(HAND TIGHTEN)
Tubing Cutter
Plumbers' Putty or CaulkingAdjustable WrenchChannel Locks
2
1
1
PUTTY
SINK
SHANK
3
4
COUPLING NUT
FERRULE
INSTALL POP-UP DRAIN
3
1
Push Tail piece (11) down into Trap (C) (threaded end up).
Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side
up) onto Drain Body (10).
Apply a bead of Putty (D) to underside of Flange (2).
Feed Drain Body (10) up through Sink (A) and thread the
Flange (2) fully onto Drain Body (10).
Tighten Locknut (5) firmly, keeping the pivot rod hole pointed
towards the back of the sink.
Assemble Pivot Rod (9) as shown in Figure-4B. Notice the
position of the Concave Washer (G).
Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot
Nut (F).
Push TAILPIECE INSERT (12) into TAILPIECE (11) and push
TAILPIECE up and thread tightly into DRAIN BODY (10).
Position Extension Rod (7) onto Pop-Up Rod (E) and tighten
Thumbscrew (6).
Remove one end of Clip (8) from Pivot Rod (9) by squeezing
ends together while sliding.
Insert Pivot Rod (9) into second or third hole in Extension
Rod (7) and reassemble Clip (8).
Drop Stopper (1) into Drain Body (10).
Adjust stopper height by repositioning Extension Rod (7) and
tightening Thumbscrew (6).
TEST INSTALLED FITTING
4
2
A
3
4
5
10
12
11
"O" RING
CHECK DRAIN CONNECTIONS
5
G
D
E
6
7
F
C
1-1/4"
F
FIGURE-4B:
8
9
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate both HANDLES to flush
water lines thoroughly.
Replace AERATOR (3).
1
Operate Pop-Up and fill lavatory with water. Check that
DRAIN STOPPER (1) makes a good seal and retains
water in lavatory. Adjust stopper height by repositioning
Pop-Up Rod (2) and tightening Thumbscrew (3).
Release DRAIN STOPPER (1) and check all drain
connections and "P" trap for leaks. Tighten if necessary.
1
3
2
3
1
2
CARE INSTRUCTIONS:
6
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
M968286
Loading...