American Standard 2650, 2660, 2454 User Manual

INSTALLATION

For These Two-Piece Toilets:

INSTRUCTIONS

Ellisse 2184 Heritage 2176 Baby Devoro 2315

Deco 2059 Cadet III 13L 2650/2660 Sonoma 2454

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE:

Pictures may not exactly define contour of china and components.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl. b. Disconnect and remove supply line. NOTE: c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases. d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE:

FINISHED WALL

Mounting surface must be clean and level before new toilet is installed!

ROUGHING-IN DIMENSIONS:

NOTE:

Distance from wall to closet flange centerline must

be as listed below:

For 4110 Tanks: A = 10" (254mm) For 4114 Tanks: A = 14" (356mm) For all other Tanks: A = 12" (305mm)

If replacing valve, first shut off main water supply!

CLOSET FLANGE

SEALANT

WAX RING

SUPPLY

REQ'D.

FINISHED

FLANGE

FLOOR

must

CLOSET

BOLT

face up!

NUT

TAPERED WASHER

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange

so bolts project through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers

marked "THIS SIDE UP"

CLOSET BOLTS

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall.

6a5

CLOSET FLANGE

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.

SAVE FOR FUTURE USE

INSTALL TOILET

Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.

DO NOT OVERTIGHTEN NUTS

OR BASE MAY BE DAMAGED!

CAUTION:

Product names listed herein are trademarks of American Standard Inc. © American Standard Inc. 2000

Saniwares

730513-100 REV. D

INSTALL BOLTS AND CAPS

BOLT CAP

Ellisse 2184

CLOSET

BOLT

Baby Devoro 2315 Deco 2059 Cadet III 13L 2650/2660 Sonoma 2454

WASHER

a. Install caps on washers. (If necessary, cut bolt height

to size before installing caps.)

b. Smooth off the bead of sealant around base. Remove

excess sealant.

NUT

7a 7b

For Tanks/Bowls using Speed Connect System (Tank mounting bolts pre-installed).

TANK MTG. BOLTS PREINSTALLED

WASHER

NUT

RUBBER GASKET

For all other Tanks/Bowls

TANK MTG.

BOLTS

WASHER

NUT

RUBBER WASHER

RUBBER GASKET

COVER MTG. CLIP

COVER

HERITAGE 2176

INSTALL TANK

a. Install large rubber gasket over

threaded outlet on bottom of tank and lower tank onto bowl so that

CLOSET

BOLT

tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washers and nuts.

b. With tank parallel to wall, alternately

tighten nuts until tank is snugged

WASHER

NUT

a. Press covers over mounting clips. (If necessary,

cut bolt height to size before installing covers.)

b. Smooth off the bead of sealant around base.

Remove excess sealant.

INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.

9a 9b

Before continuing, determine the type of water supply connecation you have from

down evenly against bowl surface.

CAUTION:

DO NOT OVERTIGHTEN NUTS MORE

THAN REQUIRED FOR A SNUG FIT!

the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.

METAL/COPPER

FLARED TUBING

CONE WASHER

COUPLING NUT

WATER SHUT-OFF

METAL FLANGED

TUBING

EXISTING WASHER

EXISTING COUPLING NUT

WATER SHUT-OFF

METAL SPIRAL

TUBING

WATER SHUT-OFF

EXISTING CONE WASHER

COUPLING NUT

VINYL/BRAIDED

CONNECTOR

WATER SHUT-OFF

LOCK NUTLOCK NUT LOCK NUT LOCK NUT COUPLING

NUT

INSTALL TANK

a. Install large rubber gasket over

threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening.

b. Insert tank mounting bolts and

rubber washers from inside tank, through mounting holes, and secure with metal washers and nuts.

c. With tank parallel to wall, alternately

tighten nuts until tank is snugged down evenly against bowl surface.

CAUTION:

DO NOT OVERTIGHTEN NUTS MORE

THAN REQUIRED FOR A SNUG FIT!

These parts must be used as illustrated to insure water-tight connection. Use of existing coupling nut may result in water leakage. Water supply tube or pipe must extend at least 1/2" inside threaded shank of valve (does not apply to flanged tubing).

Use existing coupling nut and washer.

CAUTION: DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE.

Use existing spiral cone washer. Fluidmaster cone washer may not seal completely on spiral type supply line.

Captive cone washers already included. No additional washers needed.

CAUTION: Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding.

- 2 -

With correct washers in place (see Step 9a), tighten COUPLING NUT 1/4 turn beyond hand tight. DO NOT OVERTIGHTEN.

730513-100 REV. D

+ 2 hidden pages