American Standard 2425.018WC, 2425.018W User Manual
HAMPTON™ 5’ DR OP-IN
WHIRLPOOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
BV-20
3/03
To Be Specified - Required:
❏ Color:
❏ Bath Faucet: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ Bath Caddie: 9533.100 (in Chrome only)
❏ Jet Trim Ring Kit: 9860.200-two per kit (specify finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
HAMPTON™ 5’ DROP-IN WHIRLPOOL
❏ 2425.018W Whirlpool featuring System I
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Form-fitted backrest
• Dual, molded-in arm rests
• 1.5 HP single speed, self-draining pump/motor
• Factory-installed power cord with plug
• Eight multi-directional and flow-adjustable jets
including:
- Two Ideal-flow jets
- Four body massage jets
- Two recessed back-rest jets
• Deck-mounted air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
Whirlpool Massage featuring System I
❏ 2425.018WC StayClean™ Whirlpool Massage
featuring System I:
• Same as above except with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions:
60” x 32” x 21-1/2” (1524 x 813 x 546mm)
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
HAMPTON™ 5’ DR OP-IN
WHIRLPOOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUPPORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. SUPPORT AND
ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3 WALL TILING BEAD. KIT No. TILE-BEAD AND APRON No. WBURG5-APRON AVAILABLE AND MUST BE
ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or
voided leaflet.
■
10-1/4
(260mm)
SEE FITTING
SPECS FOR
DIMENSIONS
32
(813mm)
(19mm)
FINISHED
WALL
16
(406mm)
60
12
(305mm)
3/4
(229 mm)
CUTOUT IN FLOOR FOR DRAIN
(1524mm)
ON/OFF
SWITCH
9
PROVIDE ACCESS
PUMP
TO PUMP FOR
SERVICE ON ALL
INSTALLATIONS
C/L OF
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65 & 78
(1651 & 1981mm)
(76mm)
■ LEVELING
STRINGER
NOT FOR
SUPPORT
C/L OF
OVERFLOW
(546mm)
ROUGH
FLOOR
INTEGRAL
3
C/L OF DRAIN
3-1/2
(89mm)
21-1/2
FEET
1-1/2 O.D.TAILPIECE
12
(305mm) OPT.
(102mm)
1-1/2 N.P.T.M.
THREADS
4
(8) JETS
(2) AIR VALVES
C/L OF
SHOWER ARM
FINISHED
WALL
C/L OF
VALVES
C/L OF
SPOUT
2-3/4
(70mm)
4-5/8
(117mm)
19-1/2
(495mm)
GENERAL SPECIFICATIONS FOR 2425 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
3
CUBE (FT
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
60 x 32 x 21-1/2 (1524 x 813 x 546mm)
16-1/4 x 38-1/4 (413 x 972mm)
26-1/4 x 52-1/2 (667 x 1334mm)
43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
115 Lbs. (52 Kg.)
574 Lbs. (258 Kg.)
55 Gal. (208 L.)
45 Gal. (171 L.)
15 (381mm)
15.6
35.3
PUMP 1.6 HP, 9.7 AMPS,120V.
2
(51mm)
UNDERSIDE
OF DECK
SAFE-T-HEATER
REMOVABLE
BLANK
OUTLINE OF CUTOUT
58-1/2 X 30-1/2
(1486 X 775mm)
Loading...