Page 1
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
INSTALL WITH SEAT AT HEAD END.
PRINCETON™ RECESS BATH W/ LUXURY LEDGE
BARRIER FREE
Americast® brand engineered material
❏ 2395.202 Right Hand Outlet
❏ 2395.202TC Same as above w/tub cover
❏ 2394.202 Left Hand Outlet
❏ 2394.202TC Same as above w/tub cover
• Acid resistant porcelain nish
• Recess bath with integral apron and
tiling ange
• Integral lumbar support
• Extra wide ledge for placement of toiletries
• Beveled headrest
• Full slip-resistant coverage
• End drain outlet
PRINCETON™ RECESS BATH W/ LUXURY LEDGE
for Above Floor Rough Installations
❏ 2396.202 Left Hand Outlet for above
oor installation
❏ 2396.202TC Same as above w/tub cover
❏ 2397.202 Right Hand Outlet for above
oor installation
❏ 2397.202TC Same as above w/tub cover
PRINCETON™ RECESS BATH
WITH LUXURY LEDGE
AMERICAST® BRAND ENGINEERED MATERIAL
To Be Specied:
❏ Color:
❏ Bath Faucet*:
❏ Faucet Finish:
❏ Drain: 1583.470
❏ Drain Finish:
*See faucet section for additional models available
Nominal Dimensions:
1524 x 864 x 356mm
(445mm for above oor installation)
(60" x 34" x 14")
(17-1/2" for above oor installation)
Bathing Well Dimensions:
1423 x 635 x 337mm
(56" x 25" x 13-1/4")
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.4 for Americast Plumbing Fixtures
• ASTM F-462 for Slip-resistant Bathing Facilities
• ANSI Z124.1 Ignition Test
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
Americast® brand engineered material is a composition of porcelain bonded
to enameling grade metal, bonded to a patented structural composite.
SEE REVERSE FOR PRODUCT DIMENSIONS
AND SPECIFICATIONS
© 2008 AS America Inc.
H117
Revised 2/08
Page 2
PRINCETON™ RECESS BATH
152 4mm
(60 )
864 mm
(34 )
32m m
(1- 1/4)
FIN ISHED
WAL L
19m m
(3/ 4)
FINISHED
WALL
C/L OF DRAIN
197 mm
(7- 3/4)
ROU GH
FLO OR
356 mm
(14 )
FIN ISHED
WAL L
464m m
(18- 1/4)
149 mm
(5- 7/8)
SEE FITTING SPECS
FOR DIMENSION
C/L OF
SPO UT
C/L OF
VAL VES
C/L OF
SHO WER AR M
346 mm
(13 -5/8)
25m m
(1)
165 1-1981 mm
(65 -78)
OPT IONAL
70m m
(2- 3/4)
117 mm
(4- 5/8)
1-1/ 2 N.P. T.
THRE ADS
1-1/ 2 O.D.
TAIL PIECE
102m m
(4)
64mm
(2-1 /2)
305 mm
(12 )
SEE
NOT E
89m m
(3- 1/2)
C/L OF
SUP PLIES
229mm x 305mm
(9 x 12) CUTOUT
TIL ING FL ANGE
GENERAL SPECIFICATIONS FOR 2394/2395 BATHING POOL
60 x 34 x 14 In. (1524 x 864 x 356mm)
118 Lbs. (54 Kg.)
468 Lbs. (213 Kg.)
42 Gal. (159 L)
42 x 19 In. (1067 x 483mm)
56 x 25 In. (1423 x 635mm)
9-1/2 In. (241mm)
33 Lbs./Sq.Ft. (159 Kgs./Sq.m)
6.7
20.1
INSTAL LED SIZE
WEIGHT
WEIGHT w/WATER
GAL. T O OVERFLOW
BATHIN G WELL AT SUMP
BATHIN G WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJE CTED AREA)
PTS.
CUBE ( FT3)
GENERAL SPECIFICATIONS FOR 2396/2397 BATHING POOL
60 x 34 x 17-1/2 In. (1524 x 864 x 445mm)
126 Lbs. (57 Kg.)
476 Lbs. (216 Kg.)
42 Gal. (159 L)
42 x 19 In. (1067 x 483mm)
56 x 25 In. (1423 x 635mm)
9-1/2 In. (241mm)
34 Lbs./Sq.Ft. (163 Kgs./Sq.m)
8.1
24.1
INSTAL LED SIZE
WEIGHT
WEIGHT w/WATER
GAL. T O OVERFLOW
BATHIN G WELL AT SUMP
BATHIN G WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJE CTED AREA)
PTS.
CUBE ( FT3)
STUD
SHIM
DRY WA LL
TILE
SEALAN T
TUB
ROOFIN G NAI L
STEEL
STUD
SHIM
DRY WA LL
WASHER
TILE
SEALAN T
TUB
4" (10 2mm)
DRYWAL L
SCREW
WOOD STUD S STEEL STU DS
Below is shown typical cross sections of the tub
rim showing typical wall constructions.
51 x 102mm (2 x 4) WOOD
STRIN GER F ULL L ENGT H
BARRIER FREE
WITH LUXURY LEDGE
AMERICAST® BRAND ENGINEERED MATERIAL
NOTE: Dimensions shown for 2394/2395 only. Refer to installation instruction for 2392/2393 above oor installation.
© 2008 AS America Inc.
NOTES:
LEFT HAND OUTLET SHOWN, RIGHT HAND REVERSE DIMENSIONS.
(2395.202).
SHOWN WITH POP-UP C.D. & O.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH FITTING.
CONCEALED PIPING NOT FURNISHED.
BATH FAUCET NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH BATH.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4 These measurements are
subject to change or cancellation. No responsibilit y is assumed for use of
superseded or voided leaet.
H118
Revised 2/08
Loading...