American Standard 2390.202 User Manual

AMERICAST® LIMITED LIFETIME WARRANTY

If an American-Standard Americast® brand product is found to be defective in materials or workmanship, after inspection by an authorized American-Standard representative, American-Standard will repair or, at its option, exchange the product for a similar model. This warranty extends for the lifetime of the product, so long as it remains in use in its original place of installation, except that the warranty applies to a bathing vessel’s slip-resisting surface only for the first year after the product’s initial installation.

This warranty applies only to the original purchaser and installation of these products.

This warranty does not apply to whirlpool components or to faucets, drains, mounting rims, grab bars or other accessories. If manufactured or supplied by American-Standard, such whirlpool components and accessories are covered under separate limited warranties.

This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to assure local code compliance before installation.

This warranty shall be void if the Americast® brand product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with AmericanStandard’s instructions; or if it was modified in a manner inconsistent with the product as shipped by American-Standard.

American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American-

Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or

provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.

For service under these warranties, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:

In the United States:

AMERICAN STANDARD, INC.

P.O. Box 6820

Piscataway, New Jersey 08855

Attn: Director of Consumer Affairs

For residents of the United States, warranty information may also be obtained by

calling the following toll free number: (800)442-1902

In Canada:

AMERICAN STANDARD, INC.

2480 Stanfield Road

Mississauga, Ontario Canada L4Y 1S2

Toll Free: (800) 387-0369

In Mexico:

IDEAL STANDARD, S.A. de C.V

Customer Service Manager

Planta Santa Clara,Via Morelos #330

Santa Clara Coatitla

Ecatepec de Morelos 55540,

Estado de Mexico, Mexico

Princeton™ Bath

2390.202

2392.202

2391.202

2393.202

Installation Instructions

Observe Local Plumbing and Building Codes

Introduction: Thank you for selecting American-Standard...products which

have been the benchmarks of fine quality for over 100 years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also carefully unpack and examine your new plumbing fixture.

FRAMING INSTRUCTIONS

Note recess is 1527 x 813mm (60-1/8 x 32). Cut a 229 x 305mm (9 x 12) hole in sub floor for drain, centered 362mm (14-1/4) as shown for below floor rough. Locate studs as required, then ensure rough opening dimensions are proper and supports are plumb and square.

*Install stringer as shown (346mm [13-5/8] for through the floor drain or

435mm [17-1/8] for above the floor drain.)

813mm

(32)

LEVELING SUPPORT STRINGER 51 x 102mm (2 X 4)

229 x 305mm

(9 x 12) FLOOR

CUTOUT

FOR DRAIN

762mm

(30)

362mm

(14-1/4)

1527mm

(60-1/8)

TUB WIDTH

790043-400 (Rev. G )

AMERICAN STANDARD

DRAIN

Install the overflow and drain assembly onto the tub per manufacturer's instructions.

FINISHED

WALL

Position bathtub within the recess, check level, front to back, side to side. Also check drain clearance hole in sub floor. To secure the tub to wood studs, use roofing nails immediately above the flange of the tub. To secure the tub to steel studs, use drywall screws and flat washers. (See Step 4)

Caution: Take Extra Care When Driving Nails or Screws To Avoid Damaging The Tub.

The tile or similar finished floor will be butted against the bottom of the

tub apron also holding the tub in place.

UNDERLAYMENT

FINISHED TILE FLOOR

Below is shown typical cross sections of the tub rim showing

typical wall constructions.

NAIL

DRYWALL

SCREW

EVERY STUD

SUB FLOOR

WOOD STUDS STEEL STUDS

STUD

SHIM

DRY WALL

TILE

ROOFING NAIL

SEALANT

TUB

STEEL

STUD

SHIM

DRY WALL

TILE

SEALANT

TUB

WASHER

4" (102mm) DRYWALL SCREW

23mm 15/16"

64mm 2-1/2"

ROUGH

FLOOR

BELOW FLOOR ROUGH

2390.202 2391.202

23mm 15/16"

349mm 13-3/4"

ROUGH

FLOOR

ABOVE FLOOR ROUGH

2392.202 2393.202

DIA.

64mm 2-1/2"

DIA.

64mm 2-1/2"

9" X 12" HOLE IN SUB FLOOR

FOR BELOW FLOOR ROUGH

356mm

14"

19mm

3/4"

DRAIN OUTLET

1524mm

60"

SUPPORT STRINGER

FINISHED WALL

445mm 17-1/2"

*PLUMBER NOTE: PROVIDE FULL

LENGTH SUPPORT STRINGER AT THIS POINT

229 x 305mm

60mm 2-3/8"

197mm

7-3/4"

STD. 1-1/2

FINISHED WALL

89mm 3-1/2"

FULL LENGTH

762mm

30"

19mm

48mm 1-7/8"

362mm 14-1/4"

3/4"

790043-400 (Rev. G)

51 x 102mm (2 x 4) WOOD STRINGER FULL LENGTH

LEFT HAND TUB ILLUSTRATED

RIGHT HAND TUB IS REVERSED

ROUGHING-IN

48mm

(1-7/8)

362mm (14-1/4)

762mm

(30)

197mm (7-3/4)

9 x 12 HOLE IN SUB-FLOOR

1524mm

FULL LENGTH SUPPORT STRINGER

OUTLINE OF SKID PATTERN

(60)

FINISHED WALL

19mm (3/4)

Princeton™ Bath

w/Integral Overflow

2390.202.ICH

2392.202.ICH

2390.202.IPB

2392.202.IPB

2391.202.ICH

2393.202.ICH

2391.202.IPB

2393.202.IPB

Installation Instructions

Observe Local Plumbing and Building Codes

Introduction:

Thank you for selecting American-Standard...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also carefully unpack and examine your new plumbing fixture.

89mm

(3-1/2)

PROVIDE FULL

LENGTH SUPPORT

STRINGER

AT THIS POINT

PROVIDE FULL

LENGTH SUPPORT

STRINGER

AT THIS POINT

1-1/2 N.P.S.M.

1-1/2 TUBING

THREAD INSIDE

DRAIN

SHOE

THREADS

435mm

(17-1/8)

ABOVE FLOOR ROUGH

2392.202 ICH

2393.202 ICH

346mm

(13-5/8)

BELOW FLOOR ROUGH

2390.202 ICH

2391.202 ICH

LEFT HAND TUB ILLUSTRATED RIGHT TUB IS REVERSED

60mm

(2-3/8)

FINISHED

WALL

445mm

(17-1/2)

356mm

(14)

ROUGH FLOOR

FRAMING INSTRUCTIONS

*Install stringer as shown (346mm [13-5/8] for through the floor drain or

435mm [17-1/8] for above the floor drain.)

813mm

(32)

LEVELING SUPPORT STRINGER 51 x 102mm (2 X 4)

229 x 305mm

(9 x 12) FLOOR

CUTOUT

FOR DRAIN

762mm

(30)

362mm

(14-1/4)

1527mm

(60-1/8)

The Drain Assembly is enclosed with tub models

IMPORTANT

listed above-locate and retain for tub installation before discarding tub carton

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

TUB WIDTH

791174-100 Rev. G

AMERICAN STANDARD

DRAIN INSTALLATION

Remove Lift and Turn Stopper and Tailpiece Assembly from box and check that all

parts are included. Remove Lift and Turn Stopper Assembly from Tailpiece by setting Stopper to closed position, and turning Stopper Knob counter-clockwise. (Re-install Stopper after Drain installation is completed.)

Apply plumbers putty around drain hole and pipe thread compound on threaded

end of tailpiece. Set Tailpiece in drain hole. (Lift and Turn Stopper Assembly should be removed,

and reinstalled after tub installation is completed.) From underside of tub: Place Rubber Wedge Seal on Tailpiece, small end toward tub,

and center in hole, place Brass Washer on Tailpiece, and thread on Locking Nut, flange side first. Tighten Locking Nut to obtain a uniform seal between Wedge Seal and hole in tub.

DO NOT OVERTIGHTEN!

Final hook up to tub waste can be made using either internal threads in Tailpiece (1-1/2 tubing 1-1/2—28 thd.), or external threads on Tailpiece (1-1/2—11-1/2 NPSM) for appropriate tub fittings.

TURN TO

REMOVE

STOPPER IN

CLOSED POSITION

(UNSCREW STOPPER ONCE IN

CLOSED POSITION TO REMOVE)

SET

TAILPIECE

OPEN POSITION

LIFT AND TURN STOPPER ASSEMBLY

APPLY PIPE JOINT COMPOUND TO THREADS

APPLY PLUMBERS PUTTY

STOPPER IN

STOPPER ASSEMBLY

TAILPIECE

RUBBER DRAIN SEAL

BRASS DRAIN WASHER

BRASS DRAIN NUT

STOPPER KNOB

INSTALLATION

Caution: Take Extra Care When Driving Nails or Screws To Avoid Damaging The Tub.

tub apron also holding the tub in place.

NOTE: Warranty will be voided if the drain is installed after the tub has been set in place.

DRY WALL

ROOFING NAIL

SEALANT

TUB

The tile or similar finished floor will be butted against the bottom of the

UNDERLAYMENT

FINISHED TILE FLOOR

NAIL

DRYWALL

SCREW

EVERY STUD

SUB FLOOR

Below is shown typical cross sections of the tub rim showing typical wall constructions.

STUD

SHIM

STEEL

STUD

SHIM

TILE

DRY WALL

TILE

SEALANT

TUB

WASHER

4" DRYWALL SCREW

791174-100 Rev. G

ASSEMBLE AND TIGHTEN

2 x 4 WOOD

STRINGER FULL LENGTH

2 x 4 WOOD STRINGER FULL LENGTH

WOOD STUDS STEEL STUDS

+ 8 hidden pages