ENFIELD
DECK-MOUNT BATH FILLER with EverClean™ Finish
Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets.
Installation
Instructions
2373.900
2373.920
2373.901
2373.921
EverClean Finish
•One wipe effortlessly removes spots
•Eliminates the need for cleaners and scrubbing
•Permanent surface protectant remains beautiful for the life of the faucet
•EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
Certified to comply with ANSI A112.18.1M
M968288 Rev. 1 . 1
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
IMPORTANT NOTICE TO INSTALLER!
Please check with local Code Authority for the installation requirements of this product. Some codes require an additional temperature mixing valve to limit the maximum hot water temperature and vacuum breaker
(for products with hand spray) to be installed with this product.
Required Tools
Flat Blade Screwdriver |
Adjustable Wrench |
|
*Hex key |
*Wrench |
|
Channel Locks |
*Supplied with Fitting |
|
|
|
|
|
ROUGHING-IN DIMENSIONS
|
|
|
CROSS |
|
|
LEVER |
ADJ. 6-1/2 TO 12 |
HANDLE |
|
|
HANDLE |
|
|
|
|
5-3/16" |
|
|
8-3/16 |
|
|
|
|
|
|
3-3/4" |
2-7/8 |
|
2-1/16 |
|
DIA. |
2-1/4 |
||
MOUNTING |
2-7/8" |
|
DIA. |
DIA. |
SURFACE |
|
|
|
|
|
1-1/8 DIA. |
1-1/4 |
|
|
|
MAX. |
|
|
|
8" |
|
3 |
|
|
|
|
1-1/2 MAX. |
||
|
|
|
|
|
|
|
|
|
1-3/16 DIA. |
|
|
(H) |
(C) |
|
|
|
12 MAX |
|
|
|
3/4-14 MALE 1-1/16 DIA. |
|
||
|
|
|
||
|
N.P.T. INLETS |
|
|
|
1 SPOUT ASSEMBLY
CAUTION |
Turn off hot and cold water |
supplies before beginning. |
Install RING WASHER (1) into SPOUT BASE recess. Check that O-RING (2) on end of SPOUT SHANK (3) is in place. Insert SPOUT SHANK (3) through SPOUT ESCUTCHEON (4) and into center hole on mounting surface.
Assemble RUBBER WASHER (5) and LOCKNUT (6) onto SPOUT SHANK (1). Align SPOUT ASSEMBLY and from underside of ledge secure SPOUT ASSEMBLY into position with LOCKNUT (6).
SPOUT
ASSEMBLY
SPOUT BASE |
|
1 |
2 |
|
|
||
RECESS |
|
|
|
|
|
|
|
|
2 |
3 |
|
|
|
|
|
|
|
4 |
MOUNTING |
|
|
|
SURFACE |
5
6
3 VALVE ASSEMBLY
2 PREPARE TUBE AND TEE ASSEMBLY
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center VALVE (2) location (between 6-1/2" and 12"). If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE (1) so that it will not effect the compression joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each VALVE (2) and slide onto TUBING (5).
4
3
1
5
3
4
ADJ. 6-1/2 TO 12
MOUNTING
SURFACE
2
NOTE VALVE inlet is 3/4-inch NPT male.
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4) into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is properly seated on SHANK (6). Push COUPLING (8 or 8a) into TEE (5) and attach to SPOUT SHANK (6) and tighten. Note: For product with Hand Shower, COUPLING (8) is tightened using a 10mm (3/8”)
Hex Wrench.
Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1).
9
11 MOUNTING
SURFACE
10
9 
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of |
|
left VALVE and COLD water supply to |
9 |
inlet of right VALVE using appropriate |
10 |
connector. |
|
10
4
7
12
13 6
HOT
5/16'' MIN. |
4 |
11 |
MOUNTING |
3 |
12 |
4 |
|
|
|
SURFACE |
|
5 |
|
|
|
|
|
|
|
|
|
|
2 |
FOR FITTING |
8a |
8 |
|
|
|
|
|
|||
|
|
1 |
LESS SPRAY |
|
13 |
COLD |
|
|
|
|
|||
|
|
|
|
|
M968288 Rev. 1 . 1
Loading...