American Standard 2385.060, 2385.400, 2385.500, 2385.460, 2385.560 User Manual
...
Installation
Instructions
TM
LAVATORY FAUCETS
METAL POP-UP DRAIN
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
2385.000
2385.060
2385.400
2385.460
2385.500
2385.560
Certified to comply with ANSI A112.18.1M
U.S. PATENT NO. 4,294,289
78517 Rev. 1.1
STOPPER
DRAIN
FLANGE
GASKET
WASHER
NUT
DRAIN
BODY
INDEX
BUTTON
EXTENSION
PIVOT
ROD
TAILPIECE
SET
SCREW
THUMBSCREW
CLIP
HANDLE
BUSHING
1/2 GPM
FLOW DEVICE
LOOP
HANDLE
SET
SCREW
CARTRIDGE
SCREWS
AERATOR
KEY
UNDERBODY
SCREW
SUPPLY
NUT
HANDLE
HANDLE
BUSHING
CAP
HOT LIMIT
STOP
CAP
RETAINER
CARTRIDGE
SEALS
P0P-UP
ROD
U- CHANNEL
SPACER
HEX NUT
PUTTY
PLATE
Printed
on
Recycled
Paper
Printed in U.S.A.
1
FAUCET INSTALLATION
CAUTION
Put U-CHANNEL, SPACERS, if necessary and NUTS
onto BOLTS.
Place PUTTY PLATE on SINK. Push faucet supplies
and studs through deck holes.
Insert POP-UP ROD to assure proper clearance when
faucet is assembled to the sink.
Position FAUCET on SINK.
Tighten HEXNUTS.
Turn off water at
main supply.
POP-UP
ROD
BOLT
U- CHANNEL
PUTTY
PLATE
SINK
HEX NUT
2
CONNECT SUPPLIES
Carefully bend copper supplies to meet water supply lines using
the palms of the hands to avoid kinking.
Connect HOT water supply line to LEFT tube, and COLD water
supply line to RIGHT tube using appropriate connectors.
OR
3
4
5
INSTALL POP-UP DRAIN
Push TAILPIECE down into TRAP (threaded end up).
Thread LOCKNUT, WASHER and GASKET onto
DRAIN BODY.
Apply a bead of PUTTY to underside of FLANGE.
Feed DRAIN BODY up through SINK and thread
FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the PIVOT ROD
pointed towards the back of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP ROD and
tighten THUMBSCREW.
FLANGE
SINK
LOCKNUT
TEST INSTALLED FAUCET
Move handle down into "off" position and remove AERATOR.
For vandal-resistant FLOW DEVICE, insert KEY teeth into
slots near outlet and turn.
HOT LIMIT STOP
By restricting handle rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP reduces risk of accidental scalding. To set the maximum
hot water temperature of your RELIANT faucets, all you need
to do is adjust the setting on the HOT LIMIT SAFETY STOP.
STOPPER
PUTTY
GASKET
WASHER
TAILPIECE
PIVOT
ROD
TRAP
Remove one end of CLIP from PIVOT ROD by squeezing
ends together while sliding.
Insert PIVOT ROD into second or third hole in EXTENSION
and reassemble CLIP. (EXTENSION may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION and
tightening THUMBSCREW.
CLIP
Turn on water supplies and check connections for leaks.
Operate handle up and down, left and right to flush water lines
thoroughly.
Move handle down to "off" position and replace AERATOR or FLOW
DEVICE.
"A"
PRY UPWARD TO UNLOCK
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
THUMBSCREW
EXTENSION
DRAIN
BODY
TRAP
ROD
FRONT
POP-UP ROD
EXTENSION
ROD
TAILPIECE
PRY UPWARD TO UNLOCK
AND ROTATE CLOCKWISE
"B"
PIVOT
ROD
CLIP
FRONT
6
Remove HANDLE, CAP and HOT LIMIT STOP. Follow "A" or "B"
to adjust maximum discharge temperature.
SERVICE
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR. Clean AERATOR and FLOW
RESTRICTOR. Replace AERATOR.
If faucet drips, operate handle several times from "off" to "on".
Do not apply excessive force.
Clogged CARTRIDGE inlets may cause reduced flow in "full
on" hot or cold. To clean inlets, first turn off water supply,
then:
Remove HANDLE, CAP, HOT LIMIT STOP and CARTRIDGE.
Clean inlets and MANIFOLD.
Reassemble CARTRIDGE, alternately tightening screws. Replace
HOT LIMIT STOP , CAP and HANDLE. Check flow.
ADJUSTMENT WHEN
WATER IS TOO HOT
HANDLE
SET SCREW
HANDLE
BUSHING
CAP
HOT LIMIT
STOP
CARTRIDGE
SCREWS
CAP
RETAINER
ADJUSTMENT WHEN
WATER IS TOO COLD
78517 Rev. 1.1
For toll-free information and answers to your questions, call:
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
CARTRIDGE
SEALS
P0P-UP
ROD
Loading...