American Standard 2377, 2366 User Manual
INSTALLATION INSTRUCTIONS
CADET 1.6 GPF TWO-PIECE PRESSUREASSISTED TOILETS
- Model 2333 Elongated
- Model 2366 Round Front
- Model 2377 Elongated - 16-1/2" High Bowl
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE:
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
For proper operation these products require a minimum of 20 psi line pressure
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level before new toilet is installed!
32
FINISHED WALL
CLOSET FLANGE
29 (737mm)
REF.
31 (787mm)
REF.
SUPPLY
AS
REQ'D
203mm
*
(8)
19-1/2
(495mm)
29
(737mm)
OR
31-1/2
(800mm)
ADA HEIGHT
305mm
(12)
CLOSET BOLTS
SAVE FOR FUTURE USE
305mm
(12)
DIMENSIONS (Nominal) NOTE:
FINISHED
FLOOR
Distance from wall to
closet flange centerline (rough-in) must be 12" (305 mm)
minimum.
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°,
and slide into place 6" (152 mm) apart and
parallel to wall.
Saniwares
730479-100 Rev. A
SEALANT
54
WAX RING
NUT
TAPERED WASHER
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly around
waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant
around base flange.
6
BOLT CAP
CLOSET BOLT
FLANGE
INSTALL TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"
must
face up!
7
TANK MTG.
BOLTS
SPONGE
WASHER
WASHER
NUT
CLOSET FLANGE
CLOSET BOLT
INSTALL TANK
a. Install large rubber gasket over threaded
WASHER
NUT
outlet on bottom of tank and lower tank
onto bowl so that tapered end of gasket
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS
!
b. Install caps on washers. (If necessary, cut bolt height to
OR BASE MAY BE DAMAGED!
fits evenly into bowl water inlet opening,
and tank mounting bolts go through
mounting holes. Secure with metal
washers and nuts.
b. With tank parallel to wall, alternately
tighten nuts until tank is snugged down
evenly against bowl surface.
size before installing caps.)
c. Smooth off the bead of sealant around base. Remove excess
sealant.
8
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
730479-100 Rev. A
- 2 -
CAUTION: DO NOT OVERTIGHTEN
!
NUTS MORE THAN REQUIRED
FOR A SNUG FIT!
Loading...