American Standard 2320 Elongated, 2325 Elongated User Manual
232 0
749 mm
(29 -1/ 2)
232 5
803 mm
(31 -5/ 8)
381 mm
(15 )
C/L
495 mm
(19 -1/ 2)
INSTALLATION INSTRUCTIONS
YORKVILLE 1.6 GPF TWO-PIECE
PRESSURE-ASSISTED TOILETS
- Model 2320 Elongated
- Model 2325 Elongated
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Carpenters Level Tape Measure Hacksaw
Neoprene or Graphite Felt Gasket Closet FLange Set Flexible Supply Tube (2) 5/16" Lag Bolts Sealant
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug wall waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and perpendicular to the floor before new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°,
and slide into place 6" (152 mm) apart and
parallel to floor. (Use putty to hold bolts in
place if necessary.) Brace under flooring as
needed and drill two mounting pilot holes as
shown.
S A V E F O R F U T U R E U S E
3
2
DIMENSIONS (Nominal) NOTE: Distance from floor to
closet flange centerline (rough-in) must be 4" (102 mm)
with flange surface flush to 1/16" (16mm) max. beyond
finished wall.
FLUSH TO
1/16" (16mm)
EXPOSED
CLOSET
FLANGE
CLOSET
BOLTS
730 4 19- 1 00 R ev. D
Saniwares
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE: For proper operation these products require a minimum of 20 psi line pressure
P r od u c t n a m e s l i s te d h er e i n a r e tr a d e ma r k s o f A me r i c an S t an d a r d I n c .
© Am e r i ca n S ta n d a rd I n c. 2 0 06
!
813 mm
(32 )
FIN ISH ED WAL L
FIN ISH ED
FLO OR
152 mm
(6)
32 4mm
(12 -3/ 4)
152 mm
(6)
C/L OF 1/ 2" DIA HO LES
152 mm (6) CE NTE RS
*
222 mm
(8- 3/4 )
102 mm
(4)
C/L OF
WAS TE
OUT LET
FLE X
SUP PLY
AS REQ .
152mm
(6)
PILOT
HOLES
102mm
(4)
324mm
(12-3/4)
SPONGE
WASHER
TANK MTG.
BOLTS
NUT
WASHER
NEOPRENE
SEAL
SEALANT
54
6
8
7
INSTALL NEOPRENE OR
GRAPHITE FELT SEAL*
Install seal evenly around waste
flange (horn). Apply a thin bead of
sealant around base flange.
* Note: Wax seal not recommended
for this application.
INSTALL TOILET ON FLANGE
a. Unplug wall waste opening and slide toilet towards closet
flange so bolts project through mounting holes.
b. Loosely install retainer tapered washers and nuts. Side of
washers marked "THIS SIDE UP" must face you!
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
push bowl against ring and flange.
Alternately tighten nuts until toilet is firmly anchored.
CAUTION: DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Insert the tapered washers (supplied in the kit) into the
lag bolts (not supplied). Insert bolts through mounting holes
and tighten into pre-drilled floor openings.
c. Install the four bolt caps on tapered washers. (If necessary,
cut wall bolt length to size before installing caps.)
d. Smooth off the bead of sealant around base. Remove excess
sealant.
INSTALL TANK
a. Install large rubber gasket over threaded
outlet on bottom of tank and lower tank
onto bowl so that tapered end of gasket
fits evenly into bowl water inlet opening,
and tank mounting bolts go through
mounting holes. Secure with metal
washers and nuts.
b. With tank parallel to wall, alternately
tighten nuts until tank is snugged down
evenly against bowl's sanitary ribs.
CAUTION: DO NOT OVERTIGHTEN
NUTS MORE THAN REQUIRED
FOR A SNUG FIT!
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
LAG
BOLT
BOLT HEAD
WASHER
TAPERED
WASHERS
FLANGE
BOLT
CAP
FLANGE
BOLTS
!
!
- 2 -
730 4 19- 1 00 R ev. D
BOLT
CAP
NUT &
WASHER
Loading...