American Standard 0211.100, 0211.008, 0211.800, 0211.400, 3801.452 User Manual
FINI SHED
WALL
206mm
(8-1/8)
C/L
508mm
(20)
108mm
(4-1/4)
10mm
(3/8)
203mm
(8)
140mm
(5-1/2 REF.)
552mm
(21-3/4)
70mm
(2-3/4)
660mm
(26)
PEDE STAL A NCHOR ING
SCRE W HOLE S
8mm (5/16 ) DIA.
PEDE STAL
TO W ALL
CLEA RANCE
FINISHED
FLOOR
210m m
(8-1 /4)
260m m
(10- 1/4)
19mm (3/4) DIA.
HOLES FOR
ANCHOR BOLTS
DRAIN
CHASE
203m m
(8)
1-1/4 O.D
TAILPIECE
1-1/4 O.D.
WASTE
SUPPLIES
AS REQ'D
178m m
(7)
864m m
(34)
REF.
597m m
(23- 1/2)
400m m
(15- 3/4)
PEDE STAL
SIDE SECT ION
178m m
(7)
546m m
(21- 1/2)
*
*
REMINISCENCE™ PEDESTAL SINK
• Vintage-styled basin with raised motif backsplash
and design-coordinated pedestal
• Made from vitreous china
• Rear overow
• Supplied with mounting kit
• Design matched to Reminiscence toilet
• Faucet ledge
Shown with 3801.452 Amarilis Jasmine faucet
and handles (not included)
❏ 0211.800 Faucet holes on 8" (203mm) centers
(Illustrated)
❏ 0211.400 Faucet holes on 4" (102mm) centers
❏ 0211.100 Center hole only
Nominal Dimensions:
660 x 508 x 864mm
(26" x 20" x 34")
REMINISCENCE™
PEDESTAL SINK
VITREOUS CHINA
Separate Components:
❏ 0211.008 Pedestal top-8" (203mm) centers
❏ 0211.004 Pedestal top-4" (102mm) centers
❏ 0211.001 Pedestal top-center hole only
❏ 734900-400 Pedestal only
Bowl sizes:
476mm (18-3/4") wide
292mm (11-1/2") front to back
133mm (5-1/4") deep
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.2M for Vitreous China Fixtures
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Fawn Beige ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available
© 2008 AS America Inc.
NOTES:
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP ARE
*
SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST
BE TAKEN FROM FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to c hange or cancellation. No responsibility
is assumed for use of superseded or voided pages.
J2
Revised 2/08
Loading...