American Standard 0165.060, 0163.060 User Manual
SOLAR BATH™ FOR ABOVE FLOOR
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
INSTALL WITH SEAT AT HEAD END.
762 mm
(30 )
19m m
(3/ 4)
305 mm
(12 )
102 (4)
102
(4)
102 mm
(8)
C/L OF VA LVES
(44 mm [1- 3/4"]
DIA . HOLE S)
FIN ISHED
WAL L
DRA IN SHO E
95m m
4
SPO UT
1/2 " S.P. S.
ROU GH
FLO OR
PLU MBER N OTE:
PRO VIDE S UITAB LE FULL LEN GTH
SUP PORT A T THI S P OINT.
OPT IONAL TO FI NIS HED T O F INI SHED
FLO OR (US ALLY BET WEEN 165 1 t o
198 1mm ( 65" & 78 ')
C/L OF SH OWER CUR TAIN ROD
(US UALLY 1930m m ( 76")
FRO M FIN. FLOO R)
1/2 S.P.S . OR 1/2 "
C.W .T. SU PPLIE S
FIN ISHED
WAL L
FIN ISHED
WAL L
C/L OF DR AIN
SHO WER 1/ 2" S. P.S .
NOT E: NO CONCE ALE D
PIP ING FU RNISH ED
SUM P PAD
445 mm
(17 -1/2)
711 mm
(28 )
152 4mm
(60 )
19m m
(3/ 4)
365 mm
(14 -3/8)
197 mm
(7- 3/4)
203 mm
(8)
76m m
(3)
BARRIER FREE
ROUGH INSTALLATION
❏ 0163.060 Right hand outlet
❏ 0165.060 Left hand outlet
Product Features:
• Acid resisting, enameled steel construction
• One-piece bath
• Integral apron
• For above-oor rough installations
• End drain outlet
• Full slip-resistant pattern
• Straight tiling ange
• Fully-bonded support pad
Nominal Dimensions:
1524 x 762 x 445mm
(60" x 30" x 17-1/2")
SOLAR™
BATH
ENAMELED STEEL
Bathing Well Dimensions:
1346 x 610 x 337mm
(53" x 24" x 13-1/4")
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.4 for Enameled Steel Plumbing
Fixtures
• ASTM F-462 for Slip-resistant Bathing Facilities
To Be Specied:
❏ Color:
❏ Bath Faucet*:
❏ Faucet Finish:
❏ Drain: 1583.470
* See faucet section for additional models available
© 2008 AS America Inc.
NOTES:
0165.060 LEFT HAND OUTLET (SHOWN).
0163.060 RIGHT HAND OUTLET (REVERSE DIMENSIONS).
SHOWN WITH POP-UP C.D. & O.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
CONCEALED PIPING NOT INCLUDED.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4. These measurements
are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaet.
H161
Revised 2/08
Loading...