American Standard H162, 0153.015, 0155.017 User Manual
SALEM 14™ RECESS BATH
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
INSTALL WITH SEAT AT HEAD END.
762 mm
(30 )
152 4mm
(60 )
19m m
(3/ 4)
19m m
(3/ 4)
365 mm
(14 -3/ 8)
197 mm
(7- 3/4 )
13m m
(1/ 2)
305 mm
(12 )
102 (4 )
102
(4)
102 mm
(8)
356 mm
(14 )
229 x 305mm
(9 x 12") CUT OUT
FIN ISH ED
WAL L
1-1 /2 N.P.T .M. THRE ADS
1-1 /2 O.D. TAI LPIEC E
C/L OF VALV ES
(44 mm [1-3/ 4"]
DIA . H OLES)
SPO UT
1/2 " S .P.S.
ROU GH
FLO OR
PLU MBE R NOT E:
PRO VID E SUI TAB LE FU LL LEN GTH
SUP POR T AT THI S POI NT.
OPT ION AL TO FI NISHE D T O F INISH ED
FLO OR (USUA LLY BETW EEN 16 51 to
198 1mm ( 65 " & 78')
C/L OF SHOW ER CURTA IN ROD
(US UAL LY 19 30m m (76 ")
FRO M F IN. F LOO R)
1/2 S. P.S. OR 1/2"
C.W .T. SUPP LIE S
FIN ISH ED
WAL L
FIN ISH ED
WAL L
C/L OF DRAI N
SHO WER 1/2" S. P.S.
NOT E: NO CO NCE ALED
PIP ING FURN ISH ED
SUM P P AD
711 mm
(28 )
203 mm
(8)
76m m
(3)
BARRIER FREE
❏ 0155.017 Right hand outlet
❏ 0153.015 Left hand outlet
Product Features:
• Acid resisting, heavy gauge, enameled
steel one-piece recess bath
• Integral apron
• End drain outlet
• Slip-resistant surface
• Straight tiling bead
• Fully-bonded support pad
Nominal Dimensions:
1524 x 762 x 356mm
(60" x 30" x 14")
Bathing Well Dimensions:
1346 x 610 x 337mm
(53" x 24" x 13-1/4")
SALEM 14™
RECESS BATH
ENAMELED STEEL
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.4 for Enameled Steel Plumbing
Fixtures
• ASTM F-462 for Slip-resistant Bathing Facilities
To Be Specied:
❏ Color:
❏ Bath Faucet*:
❏ Faucet Finish:
❏ Drain: 1583.470
* See faucet section for additional models available
© 2008 AS America Inc.
NOTES:
0153.015 LEFT HAND OUTLET (SHOWN).
0155.017 RIGHT HAND OUTLET (REVERSE DIMENSIONS).
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH BATH FOR
ADDITIONAL INFORMATION.
SHOWN WITH POP-UP C.D. & O.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
CONCEALED PIPING NOT INCLUDED.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4. These measurements
are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaet.
H162
Revised 2/08
Loading...