American Standard 0113.811, 0113.808, 0113.411, 0113.404, 731100-400 User Manual

23-3/4"

(603mm)

35-1/4"

(895mm)

23"

(584mm)

21"

(533mm)

4-1/4"

(108mm)

8" (203mm)

(203mm)

5-1/2"

(140mm)

1-1/4" O.D.

WASTE

SUPPLIES AS

REQUIRED

1-1/4" O.D. TAILPIECE

FINISHED

FLOOR

3/8" (10mm) DIA.

ANCHOR SCREW

HOLES ON

16" (406mm) CTRS

ANCHOR SCREW

HOLES (2) 3/8"

(10mm) DIA. ON

4-3/4" (121mm)

CTRS

28-1/4"

(718mm)

DRAIN

CHASE

OPEN

FLOOR

(203mm)

FINISHED

WALL

20"

(508mm)

20-3/4"

(527mm)

16"

(406mm)

3-3/4"

(95mm)

(203mm)

PEDESTAL ANCHORING

SCREW HOLES

3/8" (10mm) DIA.

5" (127mm) REF.

PEDESTAL/WALL

CLEARANCE

(102mm)

1-3/4" DIA.

STD. DRAIN

OUTLET

5-1/2"

(140mm)

PEDESTAL

BASE

S9 WALL-MT

HANGER

5/16" (8mm) X 1-1/16" (27mm)

ANCHOR SCREW HANGER

MTG HOLES (2) ON

4-1/2" (114mm) CTRS

1-1/4"

(32mm)

COLONY™ 24" PEDESTAL SINK

• Vitreous china lavatory and pedestal

• Front overow

• Fitting ledge with generous shelf area

• Supplied with mounting kit Shown with 2385.060 Reliant faucet (not included)

❏ 0113.411 Faucet holes on 4" (102mm) centers

(Illustrated)

❏ 0113.811 Faucet holes on 8" (203mm) centers

Nominal Dimensions:

23-3/4" x 20" x 35-1/4" (603 x 508 x 895mm)

Separate Components:

❏ 0113.404 Pedestal top 4" (102mm) centers ❏ 0113.808 Pedestal top 8" (203mm) centers ❏ 731100-400 Pedestal only

COLONY™ 24"

PEDESTAL SINK

VITREOUS CHINA

Bowl sizes:

18-1/2" (470mm) wide 12-1/2" (318mm) front to back 5-1/2" (127mm) deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.2M for Vitreous China Fixtures

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver ❏ Faucet: ❏ Faucet Finish: ❏ Supplies: ❏ 1-1/4" Trap:

NOTES:

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP ARE

SUGGESTED.

▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.

■ SUITABLE FOR REINFORCEMENT ONLY, ACTUAL DIMENSIONS MUST

BE TAKEN FROM FIXTURE. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided pages.

J14

Revised 2/08