Illustra Flex Series
1MP & 3MP Bullet
User Guide
8200-1027-05 B0
Notice
Please read this manual thoroughly and save it for f uture us e before attempting to connect or operate this unit.
The information in this manual was current when published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or
reduced to any electronic medium or machine-readable form, in whole or in part, without prior written consent of
Tyco Security Products. © 2013 Tyco Security Products. All rights reserved.
American Dynamics
6600 Congress Avenue
Boca Raton, FL 33487 U.S.A.
Customer Servi ce
Illustra Flex 1MP & 3MP Bullet
Thank you for using American Dynamics products. We support our products through an extensive worldwide
network of dealers. The dealer through whom you originally purchased this product is your point of contact if you
need service or support. Our dealers are empowered to provide the very best in customer service and support.
Dealers should contact American Dynamics at (800) 507-6268 or (561) 912-6259 or on the Web at
www.americandynamics.net.
Trademarks
The trademarks, logos, and service marks displayed on this document are registered in the United States [or
other countries]. Any misuse of the trademarks is strictly prohibited and Tyco Security Products. will
aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal
prosecution wherever necessary. All trademarks not owned by Tyco Security Products. are the property of their
respective owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos.
Not all products include all features. Availability varies by region; contact your sales representative.
2
Illustra Flex 1MP & 3MP Bullet
Table of Contents
WARNING ........................................................................................................................................................4
Preface .............................................................................................................................................................5
1. Product Ov erview ....................................................................................................................................6
1.1 Physical Characteristic s .......................................................................................................................6
2. Installation and Connection ................................................................................................................9
2.1 Unpack Everything ...............................................................................................................................9
2.2 Installation ............................................................................................................................................9
2.2.1 Checking Appearance ............................................................................................................... 9
2.2.2 Mounting the camera .............................................................................................................. 10
2.2.3 Connecting the Wires ............................................................................................................... 11
2.2.4 Adjusting the Camera Position ................................................................................................ 12
2.2.5 Adjusting the zoom & focus (vari-focal) / default & reset button ............................................. 12
2.2.6 Adjusting the Sun shield hood ................................................................................................. 13
2.2.7 Network Topology .................................................................................................................... 13
2.2.8 System Requirements ............................................................................................................. 14
2.3 Connection ........................................................................................................................................ 15
2.3.1 Default IP address ................................................................................................................... 15
2.3.2 Connecting from a computer & Viewing Preparation .............................................................. 15
2.4 Using the illustra Connect Tool to Manage Cameras........................................................................ 18
3. Administrati on and C onfi gu r atio n .......................................................................................... 19
3.1 Live View ........................................................................................................................................... 19
3.2 Configuration ..................................................................................................................................... 20
3.2.1 Image Parameters ................................................................................................................... 20
3.2.2 Network Settings ..................................................................................................................... 34
3.2.3 System Settings ...................................................................................................................... 38
3.2.4 Event Settings ......................................................................................................................... 43
3.2.5 Record Settings ....................................................................................................................... 45
Appendix: Specification of Illustra Flex Bullet ................................................................ 48
3
Illustra Flex 1MP & 3MP Bullet
WARNING
This unit operates at AC 24V/ PoE.
Installation and service should be perform ed onl y by qualif ied and ex peri enc e d technicians and comply
with all local codes and rules to maintain your warranty.
To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.
Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and
wipe with a dry soft cloth.
Do not apply benzene or thinner to the camera, which may cause the surface of the unit to be melted or
lens to be fogged.
Avoid aligning the lens to very bright objects (example, light fixtures) for long periods of time.
Avoid operating or storing the unit in the following locations:
Extremely humid, dusty, or hot/cold environments (recommended operating temperature: -40˚C to
+40˚C)
Close to sources of powerful radio or TV transmitters
Close to fluorescent lamps or objects with reflections
Under unstable or flickering light sources
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
4
Illustra Flex 1MP & 3MP Bullet
Preface
This user manual is designed as a reference for the installation and manipulations of the unit including the
camera’s features, functions, and detailed explanation of the menu tree. The reader is supposed to be able to
get following information in the manual.
Product Overview: the main functions and system requirements of the unit.
Installation and Connection: instructions on unit installation and wire connections.
Administration and Configuration: the main menu navigation and controls explanations.
5
1. Product Overview
Unit: mm
1 2 3
4 5 6 7
1.1 Physical Characteristics
Illustra Flex 1MP & 3MP Bullet
FIGURE 1-1: PHYSIC AL DIMENSION & PICTORIAL INDEX*
*Refer to table 1-1 for definitions
6
Index #
Name
Description
Au/I AI
TABLE 1-1: PICTORIAL INDEX DEFINITION
Illustra Flex 1MP & 3MP Bullet
1
2
3
4
5
6
7
I/O Connector To connect Input/ Output devices
Connects to the external power source at AC
Power Connector
24V only
To insert the RJ-45 cable for network connection
RJ-45 Ethernet Connector/ PoE
as well as PoE (Power over Ethernet)
Mount bracket To connects the Mount.
To minimize the effects of rain and sunlight on
Sun shield
image quality.
Externally adjustable focal length & focus To adjust the Near/Far and Tele/Wide controls
Reset button and Default button
a. Default: To Reset all settings of the unit to
factory default by pressing for 5 seconds
b. Reset: system restart
c. Video out
TABLE
1-2: I/O CONNECTOR DEFINITIONS 1/2
Purple (Signal)
Audio in
Green (GND)
Au/O AO
Yellow (Signal)
Audio out
Orange (GND)
Blue (Signal)
Alarm out
Brown (COM)
Red (Signal)
Alarm in
Black (GND)
7
Caution
Note
Illustra Flex 1MP & 3MP Bullet
TABLE 1-3: PIN DEFINITIONS 2/2
Return to factory default by press button
Default
Reset
for 5 seconds
System restart
Video Out To output video signal
When rotated the knob to remove the default/reset cover, please tighten the screw to avoid
water leaking after adjustment.
Connectors and field wiring terminals for external Class 2 circuits provided with marking
indicating minimum Class of wiring to be used. Class 2 shall be marked adjacent to the field
wiring terminals.
8
Illustra Flex 1MP & 3MP Bullet
2. Installation and Connection
2.1 Unpack Everything
Check everything in the packing box matches to the order form and the packing slip. In addition to this
manual, items below are included in the packing box.
One Network IR Bullet Camera
One 2-pin terminal block for power input
One CD containing Illustra Conn ec t , user manual and quick installation guide
One printed quick installation guide
One monitor out cable
One mounting template
Six screw anchors
Six screws
Please contact your dealer if any item missing.
2.2 Installation
Following tools might help you complete the installation:
a drill
screwdrivers
wire cutters
2.2.1 Checking Appearance
When first unboxing, please check whether if there is any visible damage to appe ar ance of the unit and its
accessories. The protective materials used for the packaging should be able to protect the unit from most of
accidents during transportation.
Please remove the protective part of the unit when every item is checked in accordance with the list
in 2.1 Unpacking Ever ythin g.
9
Illustra Flex 1MP & 3MP Bullet
Warning
Caution
2.2.2 Mounting the camera
1. Affix the mounting template to the desired location, knock in 6 plastic anchors after hole drilling and then
lock in 6 self-tapping screws to fasten the camera.
FIGURE 2-1: MOUNTING THE CAMERA
2. Mount the unit onto the ceiling/wall and fasten it securely.
Safety wire (fall prevention wire, not supplied)
IGURE 2-2: MOUNTING THE CAMERA
F
Depending on the material of mounting surface, different screws and anchors than those
supplied may be required. To prevent the unit from falling off, ensure that it is mounted to a
firm place (ceiling slab or channel) using a safety wire strong enough to withstand the total
weight of the unit. (Pay also attention to the finishing at the end of the wire.)
Safety wire must be connected with one end the wall/ceiling and the other to the safety-cord
screw of the unit. By cabling so, it is possible to prevent the unit from accidental falling in a
sudden at any time.
10
Illustra Flex 1MP & 3MP Bullet
2.2.3 Connecting the Wires
1. To attach the camera to the fixed place.
F
IGURE 2-3: CONNECTING THE WIRES
2. Pass all the signal cables through the mounting bracket as the sample photo shown.
3. Connect the power cable to the power plugs with one of the following options.
AC 24V: Connect 24V (～) cables to terminals ～AC 24V
PoE: Connect the RJ-45 jack to a PoE compatible network device that supplied power through the
Ethernet cable
4. Insert audio cable and alarm cable to the unit, and connect the network cable to the RJ-45 terminal of a
switch.
IGURE 2-4: CONNECTING THE WIRES
F
11
Illustra Flex 1MP & 3MP Bullet
2.2.4 Adjusting the Camera Position
1. Use the cross screwdriver loosen the cross screw on one side of the mount bracket s o that you can tilt
the camera.
2. Loosen the screw on the retaining ring to adjust the camera angle.
3. After adjustments, fasten the screws and retaining ring back to the camera.
Retaining ring
Cross screw
FIGURE 2-5: ADJUSTING THE CAMERA POSITION
2.2.5 Adjusting the zoom & focus (vari-focal) / default & reset button
1. Use a screwdriver to adjust the Near/Far and Tele/Wide controls. Please be careful when adjusting
Near/Far and Tele/Wide so as to avoid damage to the lens.
2. Use a flat head screwdriver to open the cover, then user can press default button to factory setting or
reset button to reboot system.
Tele/Wide control
Near/Far control
Default/Reset (inside)
FIGURE 2-6: ADJUSTING THE ZOOM & FOCUS (VARI-FOCAL)
Caution
After ajustment, tighten the screws to avoid water leaking issue.
12
2.
Ⅰ
Ⅱ
2.2.6 Adjusting the Sun shield hood
Move the sunshield hood forward and backward to adjust the position of sunshade.
Illustra Flex 1MP & 3MP Bullet
Caution
1. Be sure to adjust the sunshield hood in coordination with lens in case of sunshade
problems.
Don’t adjust the sun shield position excessively to avoid housing damaged.
FIGURE 2-7: ADJUSTING THE SUN SHIELD HOOD
2.2.7 Network Topology
The camera can deliver video images and audio in real time using the Internet and Intranet. It's equipped with
Ethernet RJ-45 network interface.
FIGURE 2-8: NETWORK TOPOLOGY TYPE
FIGURE 2-9: NETWORK TOPOLOGY TYPE
13
Illustra Flex 1MP & 3MP Bullet
System Software
Networking
Note
All the installation and operations should
To avoid damage to the
IEEE802.3 Ethernet Class 0 or AC24V power plug) at the same time. If using PoE, this camera
is to be connecting only to PoE networks without routing to heterogeneous
2.2.8 System Requirements
Below table lists the minimum requirement to implement and operate a unit of an Illustra Flex Bullet.
ABLE 2-1: SYSTEM REQUIREMENTS
T
System Hardware
CPU Intel Pentium 4 2.4GHz or equivalent
RAM 1 GB or above
Display NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500
Operating System Microsoft Windows XP, Windows Vista, or Windows 7
Browser Microsoft Internet Explorer 8 or above
Unit
Power Supply AC 24V / PoE
Wired* 10/100BASE-T Ethernet (RJ-45 connector)
*a switch is required for surveillance on multiple units.
comply with your local electricity safety rules.
Caution
unit, never connect more than one type of power supply (PoE
devices.
14
Illustra Flex 1MP & 3MP Bullet
2.3 Connection
2.3.1 Default IP address
Since this is a network-based unit, an IP address must be assigned at the ver y first. The unit’s default IP
address is 192.168.1.168 and sub mask is 255.255.255.0. However, if you have a DHCP server in your
network, the unit would obtain an IP address automatically from the DHCP server so that you don’t need to
change the camera’s IP address. But be sure to enable DHCP in “Network /Basic set tings ”.
2.3.2 Connecting from a computer & Viewing Preparation
2.3.2.1 Connecting from a computer
1. Make sure the unit and your computer are in the same subnet.
2. Check whether if the networking available between the unit and the computer b y exec uting ping the
default IP address. To do this, simply start a command prompt (Windows: from the Start Menu, select
Program. Then select Accessories and choose Command Prom pt.), and type “Ping 192.168.1.168”. If
the message “Reply from…” appears, it means the connection is available.
3. Start Internet Explorer and enter IP address: 192.168.1.168. A login window should pop up. In the
window, enter the default user name: admin and password: admin to log in.
Further information on the administration on the unit can be found in “
Configuration”.
3. Administration and
FIGURE 2-4: LOGIN WINDOW
15
Illustra Flex 1MP & 3MP Bullet
2.3.2.2 Viewing Preparation
Images of the unit can be viewed through Microsoft Internet Explorer 8 or above. Before viewing, follow these
steps to enable the display.
1. Enable Cookies as instructions below
In Internet Explorer, click Internet Options on the Tools menu.
On the Privacy tab, move the settings slider to Low or Accept All Cookies.
Click OK.
2. When a proxy server is used, click Internet Options on the Tools menus of Internet Explorer, select
Connect tab, click LAN button, and set proxy server.
3. Change Security in Internet options as instructions below
On Tools menu, click Internet Options.
Press the Security tab.
If the camera operates inside of the intranet, click the Intranet icon.
If the camera operates outside of the intranet, click the Internet icon.
Click Custom Level. This will open the Security Settings – Internet Zone screen.
FIGURE 2-5: SECURITY SETTINGS 1/4
16
Illustra Flex 1MP & 3MP Bullet
【
【
【
【
】
Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:
Download signed ActiveX controls】 Prompt (recommended)
Download unsigned ActiveX controls】 Prompt
Initialize and script ActiveX not marked as safe for scripting】 Prompt
F
IGURE 2-6: SECURITY SETTINGS 2/4
Automatic prompting for ActiveX controls
Enable
F
IGURE 2-7: SECURITY SETTINGS 3/4
17
【
【
Run ActiveX controls and plug-ins】 Enable
Script ActiveX controls marked safe for scripting*】 Enable
Illustra Flex 1MP & 3MP Bullet
F
IGURE 2-8: SECURITY SETTINGS 4/4
Press OK to save the settings.
Close al l Microsoft Internet Explorer Windows and restart a new window. This will allow the new
settings taking effect.
Type your setting IP address into the browser.
Then you should be able to see the camera image screen.
2.4 Using the illustra Connect Tool to M ana ge Cameras
In addition to using the IE browser to access your camera, you can alternatively use the provided tool, illustra
Connect.
illustra Connect is a management tool designed to manage your network cameras on the LAN. It can:
help you find multiple network cameras
set the IP addresses
show connection status
manage firmware upgrades
For further information on Illustra Connect, refer to the Illustra Connect User Guide, located on the CD
supplied.
18
Illustra Flex 1MP & 3MP Bullet
3. Administration and Configuration
3.1 Live View
Simply click on Live View on the top left side of the browser window while accessing the IP address of the
unit, and a live video is displayed directly in the browser window. When clicked on Configuration, a window
will be pop out for configuring “Image Parameters”, “Network Settings”, “System Settings”, “Event Sett in gs ”,
and “Record Settings”. Please refer to 3.2 Configuration
shows next right. If clicked on Logout, this window of administration and configuration will be closed.
Followings are explanations to the tabs on the left of the window.
Stream 1/Stream 2/Stream 3: The unit offers a concurrent triple* streams for optimized quality and
bandwidth. Click start or stop to play or stop the video.
Snapshot: Take a picture from live view.
Followings are explanations to the icons on the stream status bar
for more information. The current logged in identity
: This icon indicates a motion event detected. When turned on and triggered, the little man keeps
running. Please refer to 3.2.4 Event Settings for more information.
: This icon indicates an alarm event detected. When turned on and triggered, it begins to turn in red.
Please refer to 3.2.4 Event Settings for more information.
FIGURE 3-1: LIVE VIEW
* When the resolution is set to 2048x1536 or 2304x1296, only one single streaming is available.
19
Illustra Flex 1MP & 3MP Bullet
3.2 Configuration
When clicking “Configuration”, a window will be pop out for configuring “Image Parameters”, “Network
Settings”, “System Settings”, “Event Settings”, and “Record Settings”.
FIGURE 3-2: CONFIGURATION
3.2.1 Image Parameters
FIGURE 3-3: IMAGE PARAMETER
20
3.2.1.1 Codec
Illustra Flex 1MP & 3MP Bullet
FIGURE 3-4: BASIC SETTINGS - CODEC
21
Illustra Flex 1MP & 3MP Bullet
Edit Profile
This unit offers two choices of video codecs for real-time viewing: H.264 or M-JPEG. Click codec to change
desired setting as below. By default, there are 6 compression profiles can be chose for respective resolution,
frame rate, and picture quality as required. Be sure to click save to keep the desired setting.
ABLE 3-1: EDIT PROFILE OPTIONS
T
I800F-B521)
(ADC
Item Option Description
Video Codec
Resolution
Frame Rate
Bit Rate Mode
GOP
M-JPEG/H.264 Set a default codec
2048×1536
1080P(1920×1080)
SXGA(1280×960)
720P(1280×720)
SVGA(800×600)
D1(720×480 / 720x576)
4CIF(704×480 / 704x576)
VGA(640×480)
CIF(352×240 / 352x288)
NTSC: 1~30
Variable Bit Rate/Constant Bit Rate
1-64
While 2048×1536 is the highest resolution, CIF is the lowest
resolution.
Frame rate is based on second.
NTSC: H.264 or M-JPEG single stream: 2048×1536; H. 264
single stream:2304×1296, 1080P(1920×1080)@30fps,
3M(2048×1536)@15fps
Choose the bit rate control selection based on user
requirements. A higher bit rate will use higher network
bandwidth
Select the GOP (Group of pictures) number from 1 to 64.
Recovery of the lost frames will be more difficult as the
number gets bigger; on the contrary, it will increase the bite
rate obviously and aggravate the network bandwidth. The
default value is 30. GOP will be differed by frame rate setting.
22
Illustra Flex 1MP & 3MP Bullet
(ADCI600F-B521)
Item Option Description
Video Codec
Resolution
Frame Rate
Bit Rate Mode
GOP
M-JPEG/H.264 Set a default codec
720P(1280×720)
SVGA(800×600)
D1(720×480 / 720x576)
4CIF(704×480 / 704x576)
VGA(640×480)
CIF(352×240 / 352x288)
NTSC: 1~30
Variable Bit Rate/Constant Bit Rate
1-64
Frame rate is based on second.
NTSC: H.264 or M-JPEG single stream:1280×720@30fps.
Choose the bit rate control selection based on user
requirements. A higher bit rate will use higher network
bandwidth
Select the GOP (Group of pictures) number from 1 to 64.
Recovery of the lost frames will be more difficult as the
number gets bigger; on the contrary, it will increase the bite
rate obviously and aggravate the network bandwidth. The
default value is 30. GOP will be differed by frame rate setting.
23
Illustra Flex 1MP & 3MP Bullet
H.264**/M-JPEG)
TABLE 3-2: CORRELATIONS OF RESOLUTION/STREAMS/FPS/CODES 1/2
I800F-B521)
(ADC
Resolution Single stream Double stream Triple stream
2048×1536
1920×1080
1280×960
1280×720
2048×1536 @ 15fps
(H.264/M-JPEG)
1920×1080 @ 30fps
(H.264*/M-JPEG)
1280×960 @ 30fps
(H.264/M-JPEG)
1280×720 @ 30fps
(H.264/M-JPEG)
N/A N/A
1920x1080, 720x480 @ 30f ps*
1920x1080, 640x480 @ 30fps*
1920x1080, 352x240 @ 30fps*
(H.264*, H.264/M-JPEG*)
1280x960, 1280x720 @ 30fps
1280x960, 800x600 @ 30fps
1280x960, 720x480 @ 30fps
1280x960, 704x480 @ 30fps
1280x960, 640x480 @ 30fps
1280x960, 352x240 @ 30fps
(H.264/M-JPEG, H.264/M-JPEG)
1280x720, 1280x720 @ 30fps**
1280x720, 800x600 @ 30fps
1280x720, 720x480 @ 30fps
1280x720, 704x480 @ 30fps
1280x720, 640x480 @ 30fps
1280x720, 352x240 @ 30fps**
(H.264**/M-JPEG, H.264/M-JPEG**)
1920x1080, 352x240, 3 52x240 @ 30fps
(H.264, H.264/M-JPEG, H.264/M-JPEG)
1280x960, 1280x720, 352x240 @ 30fps
1280x960, 800x600, 800x600 @ 30fps
1280x960, 800x600, 720x480 @ 30fps
1280x960, 800x600, 704x480 @ 30fps
1280x960, 800x600, 640x480 @ 30fps
1280x960, 800x600, 352x240 @ 30fps
1280x960, 720x480, 720x480 @ 30fps
1280x960, 720x480, 704x480 @ 30fps
1280x960, 720x480, 640x480 @ 30fps
1280x960, 720x480, 352x240 @ 30fps
1280x960, 704x480, 704x480 @ 30fps
1280x960, 704x480, 640x480 @ 30fps
1280x960, 704x480, 352x240 @ 30fps
1280x960, 640x480, 640x480 @ 30fps
1280x960, 640x480, 352x240 @ 30fps
1280x960, 352x240, 352x240 @ 30fps
(H.264/M-JPEG, H.264/M-JPEG, H.264/M-JPEG)
1280x720, 1280x720, 800x600 @ 30fps
1280x720, 1280x720, 720x480 @ 30fps
1280x720, 1280x720, 704x480 @ 30fps
1280x720, 1280x720, 640x480 @ 30fps
1280x720, 1280x720, 352x240 @ 30fps
1280x720, 800x600, 800x600 @ 30fps
1280x720, 800x600, 720x480 @ 30fps
1280x720, 800x600, 704x480 @ 30fps
1280x720, 800x600, 640x480 @ 30fps
1280x720, 800x600, 352x240 @ 30fps
1280x720, 720x480, 720x480 @ 30fps
1280x720, 720x480, 704x480 @ 30fps
1280x720, 720x480, 640x480 @ 30fps
1280x720, 720x480, 352x240 @ 30fps
1280x720, 704x480, 704x480 @ 30fps
1280x720, 704x480, 640x480 @ 30fps
1280x720, 704x480, 352x240 @ 30fps
1280x720, 640x480, 640x480 @ 30fps
1280x720, 640x480, 352x240 @ 30fps**
1280x720, 352x240, 352x240 @ 30fps
(H.264**/M-JPEG, H.264/M-JPEG**,
*Profile 1, 2, & 3 defaults.
**Profile 4, 5, & 6 defaults.
24
Illustra Flex 1MP & 3MP Bullet
(H.264/M-JPEG, H.264/M-JPEG, H.264/M-JPEG)
(H.264/M-JPEG, H.264/M-JPEG, H.264/M-JPEG)
TABLE 3-3: CORRELATIONS OF RESOLUTION/STREAMS/FPS/CODES 2/2
Resolution Single stream Double stream Triple stream
800x600, 800x600, 800x600 @ 30fps
800x600, 800x600, 720x480 @ 30fps
800x600, 800x600, 704x480 @ 30fps
800x600, 800x600, 640x480 @ 30fps
800x600, 800x600, 352x240 @ 30fps
800×600
720×480 /
720x576
800×600 @ 30fps
(H.264/M-JPEG)
720×480 @ 30fps
(H.264/M-JPEG)
800x600, 800x600 @ 30fps
800x600, 720x480 @ 30fps
800x600, 704x480 @ 30fps
800x600, 640x480 @ 30fps
800x600, 352x240 @ 30fps
(H.264/M-JPEG, H.264/M-JPEG)
720x480, 720x480 @ 30fps
720x480, 704x480 @ 30fps
720x480, 640x480 @ 30fps
720x480, 352x240 @ 30fps
(H.264/M-JPEG, H.264/M-JPEG)
800x600, 720x480, 720x480 @ 30fps
800x600, 720x480, 704x480 @ 30fps
800x600, 720x480, 640x480 @ 30fps
800x600, 720x480, 352x240 @ 30fps
800x600, 704x480, 704x480 @ 30fps
800x600, 704x480, 640x480 @ 30fps
800x600, 704x480, 352x240 @ 30fps
800x600, 640x480, 640x480 @ 30fps
800x600, 640x480, 352x240 @ 30fps
800x600, 352x240, 352x240 @ 30fps
720x480, 720x480, 720x480 @ 30fps
720x480, 720x480, 704x480 @ 30fps
720x480, 720x480, 640x480 @ 30fps
720x480, 720x480, 352x240 @ 30fps
720x480, 704x480, 704x480 @ 30fps
720x480, 704x480, 640x480 @ 30fps
720x480, 704x480, 352x240 @ 30fps
720x480, 640x480, 640x480 @ 30fps
720x480, 640x480, 352x240 @ 30fps
720x480, 352x240, 352x240 @ 30fps
25
Illustra Flex 1MP & 3MP Bullet
(ADCI600F-B521)
Resolution Single Stream Dual Stream Triple Stream
1280x720, 1280x720, 352x240 @ 30fps
1280x720, 800x600, 800x600 @ 30fps
1280x720, 800x600, 720x480 @ 30fps
1280x720, 800x600, 704x480 @ 30fps
1280x720, 800x600, 640x480 @ 30fps
1280x720
1280x720 @ 30fps
(H.264/MJPEG)
1280x720, 1280x720 @ 30fps
1280x720, 800x600 @ 30fps
1280x720, 720x480 @ 30fps
1280x720, 704x480 @ 30fps
1280x720, 640x480 @ 30fps
1280x720, 352x240 @ 30fps
(H.264/MJPEG, H.264/MJPEG)
1280x720, 800x600, 352x240 @ 30fps
1280x720, 720x480, 720x480 @ 30fps
1280x720, 720x480, 704x480 @ 30fps
1280x720, 720x480, 640x480 @ 30fps
1280x720, 720x480, 352x240 @ 30fps
1280x720, 704x480, 704x480 @ 30fps
1280x720, 704x480, 640x480 @ 30fps
1280x720, 704x480, 352x240 @ 30fps
1280x720, 640x480, 640x480 @ 30fps
1280x720, 640x480, 352x240 @ 30fps
1280x720, 352x240, 352x240 @ 30fps
(H.264/MJPEG, H.264/MJPEG, H.264/MJPEG)
800x600
720x480
800x600 @ 30fps
(H.264/MJPEG)
720x480 @ 30fps
(H.264/MJPEG)
800x600, 800x600 @ 30fps
800x600, 720x480 @ 30fps
800x600, 704x480 @ 30fps
800x600, 640x480 @ 30fps
800x600, 352x240 @ 30fps
(H.264/MJPEG, H.264/MJPEG)
720x480, 720x480 @ 30fps
720x480, 704x480 @ 30fps
720x480, 640x480 @ 30fps
720x480, 352x240 @ 30fps
(H.264/MJPEG, H.264/MJPEG)
800x600, 800x600, 800x600 @ 30fps
800x600, 800x600, 720x480 @ 30fps
800x600, 800x600, 704x480 @ 30fps
800x600, 800x600, 640x480 @ 30fps
800x600, 800x600, 352x240 @ 30fps
800x600, 720x480, 720x480 @ 30fps
800x600, 720x480, 704x480 @ 30fps
800x600, 720x480, 640x480 @ 30fps
800x600, 720x480, 352x240 @ 30fps
800x600, 704x480, 704x480 @ 30fps
800x600, 704x480, 640x480 @ 30fps
800x600, 704x480, 352x240 @ 30fps
800x600, 640x480, 640x480 @ 30fps
800x600, 640x480, 352x240 @ 30fps
800x600, 352x240, 352x240 @ 30fps
(H.264/MJPEG, H.264/MJPEG, H.264/MJPEG)
720x480, 720x480, 720x480 @ 30fps
720x480, 720x480, 704x480 @ 30fps
720x480, 720x480, 640x480 @ 30fps
720x480, 720x480, 352x240 @ 30fps
720x480, 704x480, 704x480 @ 30fps
720x480, 704x480, 640x480 @ 30fps
720x480, 704x480, 352x240 @ 30fps
720x480, 640x480, 640x480 @ 30fps
720x480, 640x480, 352x240 @ 30fps
720x480, 352x240, 352x240 @ 30fps
(H.264/MJPEG, H.264/MJPEG, H.264/MJPEG)
26
3.2.1.2 Exposure
Illustra Flex 1MP & 3MP Bullet
FIGURE 3-5: BASIC SETTINGS – EXPOSURE
Automatic Exposure
FIGURE 3-6: AUTOMATIC EXPOSURE SETTING
Automatic Exposure controls the light intensity of picture. There are three options, AES (Automatic Electronic
Shutter), ALC, and Flickerless, to adjust for adjustment depending on conditions.
27
Illustra Flex 1MP & 3MP Bullet
Slow Shutter
Slow Shutter can be enabled if the sensitivity is still not good enough under “High” gain condition at dark.
Optimal image level can be maintained by appropriate gain and shutter combination that determined
automatically inside the uni t system. Slow Shutter can be selected from OFF, 1/30, 1/15, and 1/7.5. As slow
shutter activates, the exposure time becomes longer and frame rate becomes smaller, and moving objects
may result in blurred images.
FIGURE 3-7: SLOW SHUTTER SETTING
Max Gain
Set max gain. You can drag the bar to adjust gain level from 0 to 36.
FIGURE 3-8: MAX GAIN SETTING
Manual Exposure
Select this option to manually define exposure values of the unit.
FIGURE 3-9: MANUAL EXPOSURE SETTING
Shutter Speed
Set desired Shutter Speed from 1/60s to 1/8000s. When broadcast TV system is set to PAL, the Shutter
Speed can be set at 1/50, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, or 1/8000s; when NTSC, 1/60, 1/120,
1/250, 1/500, 1/1000, 1/2000, 1/4000, or 1/8000s. The unit will adjust the aperture according to the amount of
ambient light. Selecting 1/8000s provides the dark image.
FIGURE 3-10: SHUTTER SPEED SETTING
28
Illustra Flex 1MP & 3MP Bullet
Manual Gain
Set Manual Gain value from 0 to 36dB. This function applies to manual lens only. 36dB brightens the image
and 0dB darkens the image.
FIGURE 3-11: MANUAL GAIN SETTING
EV Adjustment
EV Adjustment can be set between 2.0 to -2.0.
FIGURE 3-12: EV ADJUSTMENT SETTING
Day Night
To set DAY/NIGHT function, simply move the cursor to select Auto, Color, or BW mode. If Color selected, the
unit is forced to stay in COLOR mode all day. If BW selected, the unit is forced to stay in NIGHT mode all day.
FIGURE 3-13: DAY NIGHT SETTING
Noise Reduction
Noise reduction is the process of removing noise from signal. Users can configure the noise reduction related
setting 0~255 to reduce noise on the screen. Selecting 255 provides the best image without noise.
FIGURE 3-14: NOISE REDUCTION SETTING
29
Illustra Flex 1MP & 3MP Bullet
BLC (Backlight Compensation)
FIGURE 3-15: BACKLIGHT COMPENSATION SETTING
Set an area for Backlight Compensation. Backlight Compensation is a function that achieves the brightness
of a selected area to optimal image level. This function is necessary when an auto iris lens tends to close due
to an intense light coming from back of object in the area wished to view so that the area is too dark and
difficult to see. In this case, users may set the area correspond to the portion wished to see. The area size
illustrations are roughly as follows.
FIGURE 3-16: BACKLIGHT COMPENSATION PICTURE SETTING
WDR (Wide Dynamic Range)
It is intended to provide clear images even under backlight circumstances where intensity of illumination can
vary excessively namely where there are both very bright and very dark areas simultaneously in the field of
view. WDR enables the capture and display of both bright and dark areas in the same frame, in a way that
there are details in both areas, i.e. bright areas are not saturated, and dark areas are not too dark.
FIGURE 3-17: WDR SETTING
Note
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set
all the data and options back to defaults.
30
Illustra Flex 1MP & 3MP Bullet
3.2.1.3 White Balance
FIGURE 3-18: WHITE BALANCE SETTING
White Balance controls color on the screen. Mode can be set to Auto (default) or Manual mode. The
color temperature range is 2800°K ~ 8500°K.
Set manual gain value of R Gain, G Gain, & B Gain from level 0 to 255.
The red (R) gain is used to adjust the color red in the viewing image. It allows adjusting red gain
manually according to user requirement ranging from level 0 to 255.
The green (G) gin is used to adjust the color of green in the viewing image. It allows adjusting green
gain manually according to user requirement ranging from level to 255.
The blue (B) gain is used to adjust the color of blue in the viewing image. It allows adjusting blue gain
manually according to user requirement ranging from level 0 to 255.
3.2.1.4 Basic Color
FIGURE 3-19: BASIC COLOR SETTING
31
Illustra Flex 1MP & 3MP Bullet
Brightness adjustment Set picture brightness from level -255 to 255. Selecting 255 provides brightest the image.
Contrast
Set picture contrast from level 0 to 255. Selecting 255 provides highest contrast.
Hue
Set picture hue from level -15~15. Select ing 15 prov id es the deep hue.
Saturation
Saturation describes the difference of a color from the gray of the same lightness. Increasing saturation
deepens the colors of your images, making reds redder and blues bluer. Users can adjust picture saturation
level from 0 to 255. Decreasing saturation brings the image closer to a grayscale (that is, monochrome or
black-and-white) image. Selecting 255 provides highest image saturation.
Sharpness
Increasing the sharpness value will sharpen the edges and small feature of viewing images. If the edges
appear too smooth or blurred, increase the sharpness; otherwise, decrease the sharpness. Sharpness value
can be set from 0 to 15. Selecting 15 provides the sharpest image.
Gamma Correction
Set gamma correction. You can select “1” or “0.45”.
Flip Mirror
Set image to be left or right, upside or down and both. Select “OFF”, “Flip”, “Mirror” or” Both” to activate or
deactivate the mirror function.
Note
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set
all the data and options back to defaults.
3.2.1.5 Privacy Zone
Privacy Color Setting
Users can select a desire color for the privacy zone color.
FIGURE 3-20: PRIVACY COLOR SETTING
Privacy Zone Setting
Enable button “ON”, then to start mask setting.
Use mouse to drag a mask rectangle on the screen, click “Save Mask Zone” to complete the selection.
To cancel the mask setting simply clicks “Clean Mask Zone”.
32
Note
Caution
Illustra Flex 1MP & 3MP Bullet
At max 8 masks can be set on the screen.
The privacy zone area is a factor increased by 16. That implies we have to round the length
and width of the privacy zone to meet this rule. After rounding the algorithm, the result of
privacy zone will be plus or minus 16% of the user selected area.
FIGURE 3-21: PRIVACY ZONE SETTING
IGURE 3-22: PRIVACY ZONE DIAGRAM
F
33
3.2.2 Network Settings
Below explains how to configure a wired network connection for the unit.
Illustra Flex 1MP & 3MP Bullet
FIGURE 3-23: NETWORK SETTINGS
Camera Name: Enter a desired camera name or use the default name.
DHCP: If selected, the unit will automatically obtain an available dynamic IP address from the DHCP
server each time it connects to the LAN.
IP Address: Manuall y input IP address when DHC P off selected.
Subnet Mask: Please use default number: 255.255.255.0. If the subnet mask is not properly configured,
the unit may not be able to communicate with other devices on the network.
Default Gateway: Leave blank as default setting. It is not necessary to enter Default Gateway if it is not
used. Ask your Network Administrator for Default Gateway information.
Primary DNS: (same as above)
Secondary DNS: (same as above)
OSD: When set to “ON”, the camera name can be show on the screen.
34
Illustra Flex 1MP & 3MP Bullet
3.2.2.1 FTP
In this page, users can activate a FTP Server to reach SD card for recordings.
Simply click “OFF” to disable the FTP function.
Simply click “ON” to activate the FTP function, and follow the following procedures to set up related
settings.
Enter a login ID if activated the FTP function.
Enter a password associated with the login ID.
Re-enter the password to confirm it.
Determine the number of maximum connections by key-in a number in the Max Simultaneous
Connections field. Note: This is the maximum of FTP Client connections, not the maximum of IE
Window’s connections.
To log on the FTP, simply enter ftp://<Login ID>:<Password>@<ip address> in the location field of Microsoft’s
Internet Explorer and the recordings will be shown up. The default setting
is ftp://admin:admin@192.168.1.168
recordings.
. Refer to the names of file and the folder for date and time of
FIGURE 3-24: FTP SETTINGS
Note
3.2.2.1 RTSP
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set
all the data and options back to defaults.
To enable RTSP, simply enter the Login ID, Password, and Multicast Address, and then select “ON” in
Authentication.
35
FIGURE 3-25: RTSP & AUTHENTICATION SETTINGS
Illustra Flex 1MP & 3MP Bullet
FIGURE 3-26: RTSP STREAM1 / STREAM2 / STREAM 3 SETTINGS
Multicast Address
The IP address for multicasting ought to be from 224.0.1.1 to 239.255.255.254. After desired options and
values are chosen, please be remembered to click “save” button to save all settings.
Note: RTSP URLs for RTSP Stream 1, RTSP Stream 2, and RTSP Stream3 are: rtsp://(ip address)/(stream 1),
rtsp://(ip address)/(stream 2), rtsp://(ip address)/(stream 3) respectively.
For example: rtsp://192.168.1.168/stream1
Metadata
Metadata plays a significant role for media applications especially for ONVIF compatible NVR.
Turn on the metadata option and there will be an additional track in the RTSP connection response message.
The additional track name is “vnd.onvif” and this track is for event data transmission. Once if the event (motion,
alarm) is triggered, RTSP server will transmit event data to RTSP client (usually NVR). RTSP client can
receive these data and analyze them . The event data usuall y includ es event trigger time, coordinate…etc.
3.2.2.3 SNMP
SNMP (Simple Network Management Protocol) is an Internet standard protocol on top of application layer that
restructures the exchange of management information among network-attached nodes, which helps
administrators to remotely manage network devices and master network problems with ease.
36
Illustra Flex 1MP & 3MP Bullet
FIGURE 3-27: SNMP SETTINGS 1/2
SNMP V1: Tick “ON” or “OFF” to enable or disable.
SNMP V2: Tick “ON” or “OFF” to enable or disable.
SNMP V3: Tick “ON” or “OFF” to enable or disable. Enter password corresponding to User Name.
SNMPv3 provided more security features to SNMP.
Read/Write Community String: Enter the names of Read Community and Write Community.
Trap: Tick “ON” or “OFF” to enable or disable. Input IP address of Trap Host.
Heartbeat: Tick “ON” or “OFF” to enable or disable. Input IP address & Interval of Heartbeat Host &
Heartbeat.
FIGURE 3-28: SNMP SETTINGS 2/2
Download: Click “Download” to get specifics of MIB (Management Information Base). MIBs describe the
structure of the management data of a device subsystem; they use a hierarchical namespace containing
object identifiers (OID). Each OID identifies a variable that can be read or set via SNMP.
Note
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set
all the data and options back to defaults.
37
Illustra Flex 1MP & 3MP Bullet
3.2.3 System Settings
3.2.3.1 Date & Time
Synchronization Mode
Synchronization supports three different modes: Manual, Computer Clock, and NTP Server.
FIGURE 3-29: SYNCHRONIZATION MODE SETTINGS
Set manual: Set up the date and time of the unit in the Date and Time field manually.
FIGURE 3-30: SET MANUAL SETTINGS
Synchronize with Computer Clock: Select this one to synchronize the d ate and time of the unit with the
computer clock.
FIGURE 3-31: SYNCHRONIZATION WITH COMPUTER CLOCK SETTINGS
Synchronize with NTP Server: Select NTP in the Synchronization Mode to synchronize the date and time
with the dedicated.
NTP Server: Input IP address or URL of the dedicated NTP server.
NTP Synchronize Period: Select interval to synchronize with the NTP server.
NTP T ime Adjustment T est: Press the button to test synchronization with the dedicated NTP server.
FIGURE 3-32: NTP SETTINGS
38
Illustra Flex 1MP & 3MP Bullet
DST
Time Zone: Select the time difference between Greenwich Mean Time and where the unit is located.
Daylight Saving: Tick “Daylight Saving” to enable the daylight -saving function if in a daylight saving time zone
(effective in NTP mode only).
FIGURE 3-33: DST SETTINGS
Note
3.2.3.2 User Management
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set
all the data and options back to defaults.
Press the item-user management on setting menu, and system password and language (only including
English) can be setup. The default setting for system Admin ID, password, and language are admin, admin,
and English respectively; however, desired Admin ID and password can be entered at this field.
FIGURE 3-34: ADMIN SETTINGS
Besides administrator, guests can access the unit under authorization from system administrator by privilege
controller. User1~5 are allowed to review the live picture only. No operation will be enforced without any
authorization. The default login name and password of guests are “user 1” (user+ 1~5) and “0000”; however,
desired login name and password of guests may be altered like those of administrator’s.
IGURE 3-35: GUEST SETTINGS
F
Caution
The login ID and Password is supported max 32 characters. Only space key is invalid.
Finally, click Save to keep the settings.
39
Illustra Flex 1MP & 3MP Bullet
3.2.3.3 Audio
Audio setting can be setup by enabling audio input and output.
Audio Input
Type: Select one of the two audio compression coding, G711a or G711u.
Audio Input: Set to "ON" when receiving audio from a microphone connected to the unit.
Audio Input Level: Select among High, Mid, and Low for input level.
FIGURE 3-36: AUDIO SETTINGS
Audio Output
Audio Output: Set to "ON" when delivering audio to a speaker connected to the unit.
Audio Output Level: Select among High, Mid, and Low for output level.
Note
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set
all the data and options back to defaults.
40
Illustra Flex 1MP & 3MP Bullet
3.2.3.4 Firmware
System Information about Firmware Version, Mac Address, MCU Version, and Model Name are revealed
here as below figure. Users can update system firmware if available. All camera motions will shut down
during firmware update. Please close any other screens before firmware update. Never disconnect power or
LAN cable during the firmware update process. It takes approximately 3 minutes for the unit to reboot after
firmware update process. Please reboot the computer as well after firmware update process. Again, power
can’t be lost when updating firmware since it will cause the update failure and manufacturer maintenance will
be required.
IGURE 3-37: FIRMWARE UPDATE 1/2
F
IGURE 3-38: FIRMWARE UPDATE 2/2
F
41
Illustra Flex 1MP & 3MP Bullet
3.2.3.5 Configuration
Video Type
Select “NTSC” or “PAL” as required. Flickering by fluorescent light can be reduced by selecting “PAL” if the
power frequency is 50Hz, “NTSC”, if 60Hz.
IGURE 3-39: VIDEO TYPE SETTING
F
Import Configuration Settings
This function is designed to upload configuration setting from the client computer to the unit.
F
IGURE 3-40: IMPORT CONFIGURATION SETTING
Export Configuration Settings
This function is designed to export configuration settings to the client computer.
IGURE 3-41: EXPORT CONFIGURATION SETTING
F
Configuration
This function is design to restart camera and reset all configuration settings back into factory default.
Press “Software Factory Default” to reset all settings back to factory default excluding network setting.
Press “Hardware Factory Default” to reset all settings back to factory default including network setting.
IGURE 3-42: CONFIGURATION SETTING
F
42
Illustra Flex 1MP & 3MP Bullet
3.2.4 Event Settings
3.2.4.1 Motion Detection
This function is designed to record video once the unit detects a motion.
F
IGURE 3-43: MOTION DETECTION SETTING 1/2
Enable: Select “ON” or “OFF” to use this function.
Sensitivity: Choose different levels of sensitivity from high, medium, and low. “High”: Motion is activated with
slight changes in brightness or motion. “Low”: Motion is activated with big changes in brightness or motion.
Set Motion Area: Set the desired area to trigger motion detection. The motion setup screen will be popped out
for defining the detection area by dragging the mouse.
IGURE 3-44: MOTION DETECTION SETTING 2/2
F
43
Illustra Flex 1MP & 3MP Bullet
3.2.4.2 Alarm
When an alarm is connected, the unit triggers an alarm only once the status (open or closed) changed. When
an alarm event is detected, an alarm message would be displayed on the Web-Client screen for notification.
Alarm Input
Alarm Input: Set the Alarm Input as “ON” or “OFF”.
Input Type: Choose NO for normally open or NC for normally close. NO (Normally Opened): An alarm will be
triggered when the external contac t clos es . NC (Normally Closed): An alarm will be triggered when the
external contact opens.
IGURE 3-45: ALARM INPUT SETTING
F
Alarm Output
When the Mode is set to “On”, external devices such as sirens or flashing lights that connected to the alarm
output connector will signal for alarm activation.
Note
IGURE 3-46: ALARM OUTPUT SETTING
F
Please click “Save” button to save your settings. Users can also click “Reset to Default” to set
all the data and options back to defaults.
44
Illustra Flex 1MP & 3MP Bullet
3.2.5 Record Settings
3.2.5.1 FTP Record
Recording Condition
Users can save image files via FTP by setting FTP recording condition beforehand.
IGURE 3-476: RECORDING CONDITION SETTING
F
Recording Condition: You can store your image files base on your scheduled recording, recording by alarm or
recording by motion.
FTP Server
FTP (File Transfer Protocol) is used as a service component to transfer files by simply entering the FTP IP
address or hostname with the Login ID and password.
IGURE 3-48: FTP SERVER SETTING
F
FTP IP Address: Input a server name or address.
Login ID: Input a user name with privilege to access the server.
Password: Input the password associated with Login ID.
FTP Port: Set “21” as default or change to dedicated number.
Note
The default login name and password are “guest” and “1234”.
45
Illustra Flex 1MP & 3MP Bullet
Scheduled Recording Table
Determine the recording condition: OFF, All Day, Schedule 1, or Schedule 2 from scheduled recording table
during 24/7.
FIGURE 3-49: SCHEDULED RECORDING TABLE
Recording cycle: Set a time interval for recording images.
IGURE 3-50: RECORDING CYCLE SETTING
F
Server Path: Set the data path where the data is to be stored on the server.
IGURE 3-51: SERVER PATH SETTING
F
46
Illustra Flex 1MP & 3MP Bullet
Alarm Settings & Motion Settings
This function is to define the way to record video onc e a motion/alarm event is detected by the unit.
IGURE 3-52: ALARM SETTINGS & MOTION SETTINGS
F
Pre Recording Frame: Set the number of frame to be recorded immediately before a motion occurs.
Pre Recording Cycle: Set a time interval before recording.
Recording Frame: Set the number of frame when recording.
Recording Cycle: Set a time interval for recording.
At last, press “Save” to keep the settings.
47
Illustra Flex 1MP & 3MP Bullet
Model Type
ICR Day/Night IR Bullet Camera
Model No.
ADCi800F-B521
ADCi600F-B521
Signal System
NTSC
Warranty
1 year
Image System
Image Sensor
1/3" AR0330
Sensor Type
CMOS
Optical System
Lens Mount
D14
Auto Iris Control
DC Iris
Focal Length
9~22mm
F No
1.5
Tele: 13° (H), 9.8° (V)
Day / Night
Mechanical ICR
Electric
Digital Noise Reduction
3D
Gamma Correction
0.45/1
Minimum Illumination
F:1.5, CL: 0.5 lux @ 50IRE, IR LED ON: 0 lux, 1/30, Max. Gain
S/N Ratio
50dB (AGC off)
Gain Control
Off / On, Selectable
White Balance
ATW(2800K~8500K) / Manual
Electric Shutter
1/30~1/8000 sec
Audio In/Out
Audio In/Out
Video Output
Monitor Out
Alarm In/Out
Alarm In x1 / Alarm Out x1
Network Specifications
Video Compress
H.264 / M-JPEG
Video Streaming
Triple Streaming
3M(2048 x 1536) @ 15fps
CIF(352x240)
DHCP, ARP, NTP, SNMP
Slow Shutter
Yes
WDR
Digital WDR
Back Light Compensation
Off / On (6 Area Selectable)
Audio Format
G711-Alaw / G711-Ulaw
Privacy Zone
Yes
Motion Detection
Yes
Security Access
Multiple user access levels with password protection
Users
1 Administrator, 5 Viewers
Appendix: Specification of Illustra Flex Bullet
Angel Of View
Frame Rate
Resolution
Wide: 30.6° (H), 22.6° (V)
1080P(1920 x 1080) @ 30fps /
2048x1536(QXGA),
1080P(1920x1080),SXGA(1280x960),
720P(1280x720), 800x600(SVGA),
D1(720x480),
4CIF(704x480),VGA(640x480),
720P(1280x720) @ 30fps
720P(1280x720),
800x600(SVGA), D1(720x480),
VGA(640x480), CIF(352x240)
Network Protocols
IPv4, HTTP/HTTPS, TCP, RTSP/RTCP/RTP, ICMP, UDP, IGMP, DNS,
48
Applications
SDK 2.0
ONVIF
PASS ONVIF Compliance tool V12.06
Web Browsing Requirements
Internet explorer 8.0 or above
Mechanism
Dimensions
Φ115mm x264mm
IP rating
IP66
Weight
1650g
Connectors
Alarm In/Out: terminal block
IR
IR Distance
25M
IR LED
48 pcs
IR Wavelength
850nm
Power Supply
(PoE is not supported Heater)
Power Consumption
15W Max. (w/ LED on & Heater)
Environment
Operating Temperature
-40°C to 40°C
Operating Humidity
90%, non-condensing
Storage Temperature
-20°C to 60°C
Storage Humidity
90%, non-condensing
Safety Regulation
FCC
Class A
CE Regulation
Class A
Illustra Flex 1MP & 3MP Bullet
Network: RJ-45 connector
Power in: removable terminal block
Audio In/Out: terminal block
Power Requirement
AC24V,PoE
Note: Product specifications and pictures are subject to change without notice.
49
Loading...