American Dynamics ADCC0200, ADCC0300 User Manual

ControlCenter

8200-0855-05 A0

TM

ADCC0200
ADCC0300

Keyboard Installation and Operation Instructions

ADCC0200 and ADCC0300

Sensormatic Electronics Corporation.

Sensormatic Electronics Corporation.
Sensormatic Electronics Corporation.

When unpacking your new Tyco Video product, check for missing or damaged items. If
any item is missing, or if damage is evident, DO NOT INSTALL OR OPERATE THIS PRODUCT
Contact your nearest dealer for assistance.

2007

Notice

The information in this manual was current when published. The manufacturer reserves the right to
revise and improve its products. All specifications are therefore subject to change without notice.

Copyright

Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine-readable form, in whole or in part,
without prior written consent of American Dynamics Video Products Division.

© Copyright 2004

American Dynamics Video Products Division

6795 Flanders Drive San Diego, CA 92121 U.S.A.

Trademarks

MegaPower™ and ControlCenter™ are trademarks of American Dynamics Video Products Division.

Trademarked names are used throughout this manual. Rather than place a symbol at each occur­rence, trademarked names are designated with initial capitalization. Inclusion or exclusion is not a
judgment on the validity or legal status of the term.

Important Information

Before proceeding, please read and observe all instructions and warnings contained in this manual.
Retain this manual with the original bill of sale for future reference and, if necessary, warranty
service.

When unpacking your new American Dynamics product, check for missing or damaged items. If
any item is missing, or if damage is evident, DO NOT INSTALL OR OPERATE THIS PRODUCT.
Contact your dealer for assistance.

NOTE

This product is supplied with a printed English manual. The manual is also provided in other
languages (French, Spanish, German) on the included CD.

For your Records

Complete the following product purchase information. The factory requests this information when
contacted for technical support. It is also valuable in case of loss or theft.

Purchase Date: __________________________

Serial Number: __________________________

ii

Keyboard Installation and Operation

TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.

DO NOT INSTALL THIS PRODUCT IN HAZARDOUS AREAS WHERE HIGHLY COMBUSTIBLE
OR EXPLOSIVE PRODUCTS ARE STORED OR USED.

THE EQUIPMENT SUPPLIED WITH THIS MANUAL IS DESIGNED FOR USE IN A GENERAL PUR­POSE CCTV INSTALLATION AND HAS NO OTHER FUNCTION. DO NOT EXCEED THE VOLT­AGE AND TEMPERATURE LIMITS GIVEN IN THE SPECIFICATIONS. ONLY USE YOUR KEY­BOARD IN A CLEAN, DRY, DUST-FREE ENVIRONMENT.

BEFORE CLEANING, ISOLATE THE UNIT. USE ONLY A DRY, LINT-FREE CLOTH. DO NOT USE
CLEANING FLUIDS OR SOLVENTS.

THE LIGHTNING FLASH/ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, ALERTS
THE USER TO THE PRESENCE OF A SHOCK HAZARD WITHIN THE PRODUCT’S ENCLOSURE.

CAUTION: This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

Radio Frequency Emissions

Federal Communications Commission Code of federal regulations Part 15.
British Standard BSEN55022:1998 Limits and methods of measurement of radio disturbance characteristics of

information technology equipment.

Electrical Safety

British Standard BSEN60950:1999 Safety of information technology equipment, including electrical business
equipment.

Immunity

British Standard BSEN50130-4 Alarm Systems Part 4 Electromagnetic compatibility Product family standard:
Immunity requirements for components of fire, intruder and social alarm systems.

EU Conformance Statement

A Declaration of Conformity in accordance with the above EU standards has been made and is on file with the
manufacturer.

The manufacturer declares that the product supplied with this document is complaint with the provisions of the
EMC Directive 89/336 EEC and associated amendments and the Low Voltage Directive LVD 73/23 EEC.

Regulatory Notices

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

iii

ADCC0200 and ADCC0300

PPOUR RÉDUIRE LES RISQUES D’ÉLECTROCUTION, NE PAS DÉPOSER LE COUVERCLE.
AUCUN COMPOSANT NE PEUT ÊTRE RÉPARÉ PAR L’UTILISATEUR. FAIRE APPEL À UN
TECHNICIEN DE MAINTENANCE COMPÉTENT.

POUR PRÉVENIR TOUT RISQUE D’INCENDIE OU D’ÉLECTROCUTION, NE PAS EXPOSER
CETTE UNITÉ À LA PLUIE NI À L’HUMIDITÉ.

NE PAS INSTALLER CET APPAREIL DANS UN ENDROIT DANGEREUX OÙ DES PRODUITS
HAUTEMENT INFLAMMABLES OU EXPLOSIFS SONT STOCKÉS ET UTILISÉS.

L’ÉQUIPEMENT FOURNI AVEC LE PRÉSENT MANUEL EST CONÇU POUR ÊTRE UTILISÉ
DANS LE CADRE GÉNÉRAL DE LA SURVEILLANCE PAR CAMÉRA À CIRCUIT FERMÉ (CCTV)
ET N’A AUCUNE AUTRE FONCTION. NE PAS DÉPASSER LES SEUILS DE TENSION ET DE
TEMPÉRATURE INDIQUÉS DANS LES CARACTÉRISTIQUES TECHNIQUES. N’UTILISER
L’UNITÉ MATRIX QU’EN ENVIRONNEMENT PROPRE, SEC ET EXEMPT DE POUSSIÈRE.

AVANT DE LE NETTOYER, IL DOIT ÊTRE ISOLÉ. UTILISER UNIQUEMENT UN CHIFFON
SEC ET NON PELUCHEUX. NE PAS UTILISER DE PRODUITS DE NETTOYAGE NI DE
DISSOLVANTS.

LE SYMBOLE EN FORME D’ÉCLAIR/TÊTE DE FLÈCHE DANS UN TRIANGLE ÉQUILATERAL
SIGNALE LA POSSIBILITÉ D’UN RISQUE D’ÉLECTROCUTION À L’INTÉRIEUR DU BOÎTIER
DU PRODUIT.

ATTENTION: il s’agit d’un produit de classe A. Dans un environnement domestique, ce produit est susceptible
de provoquer des interférences radio, auquel cas l’utilisateur devra éventuellement prendre des mesures
appropriées.

Émission de fréquences radio

Paragraphe 15 du code des réglementations fédérales de la FCC (Federal Communications Commission).
Norme britannique BSEN55022:1998: limites et méthodes de mesure des caractéristiques de perturbation

radio des équipements informatiques.

Sécurité électrique

Norme britannique BSEN60950:2001 : sécurité des équipements informatiques, notamment les équipements
électriques commerciaux.

Immunité

Norme britannique BSEN50130-4 : systèmes d’alarme, 4e partie, compatibilité électromagnétique Norme de
famille de produits : caractéristiques d’immunité des composants des systèmes anti-incendie, anti-intrusion et
d’alarme sociaux.

Déclaration de conformité UE

Une déclaration de conformité aux normes ci-dessus de l’Union Européenne a été réalisée et est conservée
chez le constructeur.

Le constructeur déclare le produit accompagnant ce document conforme aux dispositions de la Directive 89/
336 de la CEE et ses modifications sur la compatibilité électromagnétique et de la directive LVD 73/23 de la
CEE sur les basses tensions.

Avis réglementaires

Cet équipement est conforme au paragraphe 15 des réglementations de la FCC. Son utilisation est sujette aux
deux conditions suivantes : (1) cet équipement ne doit pas générer d’interférences nuisibles et (2) cet équipement
doit accepter les interférences éventuelles, notamment les interférences susceptibles de provoquer un
fonctionnement indésirable.

iv

Keyboard Installation and Operation

UM STROMSCHLÄGE ZU VERMEIDEN, DARF DIE ABDECKUNG NICHT ENTFERNT WERDEN.
DAS GERÄT ENTHÄLT KEINE DURCH DEN ANWENDER WARTBAREN TEILE.
WARTUNGSARBEITEN DÜRFEN NUR VON QUALIFIZIERTEM WARTUNGSPERSONAL
DURCHGEFÜHRT WERDEN.

DIESES GERÄT DARF KEINER FEUCHTIGKEIT ODER REGEN AUSGESETZT WERDEN.
DIESES PRODUKT DARF NICHT IN GEFAHRENBEREICHEN INSTALLIERT WERDEN, IN DENEN

LEICHT ENTFLAMMBARE ODER EXPLOSIVE PRODUKTE GELAGERT ODER VERWENDET
WERDEN.

DIE ZUSAMMEN MIT DIESEN ANLEITUNGEN GELIEFERTE AUSRÜSTUNG IST FÜR DEN
EINSATZ IN ALLGEMEINEN CCTV-ANWENDUNGEN KONZIPIERT UND DIENT KEINEM ANDEREN
ZWECK. DIE IN DEN TECHNISCHEN DATEN ANGEGEBENEN SPANNUNGS- UND
TEMPERATURGRENZEN DÜRFEN NICHT ÜBERSCHRITTEN WERDEN. VERWENDEN SIE IHR
KEYBOARD NUR IN EINER SAUBEREN, STAUBFREIEN UMGEBUNG.

DAS GERÄT MUSS VOR DER REINIGUNG VON DER VERKABELUNG GETRENNT WERDEN.
VERWENDEN SIE NUR EIN TROCKENES, FLUSENFREIES TUCH. VERWENDEN SIE KEINE
REINIGUNGSFLÜSSIGKEITEN ODER LÖSUNGSMITTEL.

DAS BLITZ-/PFEIL-SYMBOL IN EINEM GLEICHSEITIGEN DREIECK VERWEIST DEN BENUTZER
AUF EINE STROMSCHLAGGEFAHR IM INNEREN DES GEHÄUSES.

VORSICHT: Dies ist ein Produkt der Klasse A. Es kann in Wohnbereichen Funkstörungen verursachen, in welchem
Fall das Ergreifen entsprechender Maßnahmen durch den Benutzer erforderlich sein könnte.

Funkfrequenzemissionen

Bundesbehördliche Richtlinien gemäß Federal Communications Commission Code Part 15.
British Standard BSEN55022:1998 – Messgrenzen und -verfahren für Funkstörungscharakteristiken von

informationstechnischer Ausrüstung.

Elektrische Sicherheit

British Standard BSEN60950:1999 – Sicherheit von informationstechnischer Ausrüstung, einschließlich elektrischer
Geschäftsausrüstung.

Immunität

British Standard BSEN50130-4 – Alarmsysteme, Teil 4, elektromagnetischer Kompatibilitätsstandard für die
Produktgruppe: Immunitätsanforderungen für Komponenten von Feuer-, Einbruchs- und öffentlichen
Alarmsystemen.

EU-Konformitätserklärung

Eine Konformitätserklärung gemäß der o. g. EU-Standards ist erfolgt und liegt beim Hersteller vor.
Der Hersteller erklärt, dass das mit diesem Dokument gelieferte Produkt die Anforderungen der EMC-Direktive

89/336 EEC und aller diesbezüglichen Änderungen sowie der Direktive für Niederspannung LVD 73/23 EEC
erfüllt.

Aufsichtsbehördliche Hinweise

Dieses Gerät entspricht Teil 15 der FCC-Richtlinien. Der Betrieb ist vorbehaltlich der beiden folgenden Bedingungen
gestattet: (1) dieses Gerät darf keine schädlichen Störungen verursachen, und (2) dieses Gerät muss alle Störungen
akzeptieren, einschließlich solcher, die den Betrieb beeinträchtigen könnten.

v

ADCC0200 and ADCC0300

PER RIDURRE IL RISCHIO DI SHOCK ELETTRICI, NON RIMUOVERE IL COPERCHIO. L’INTERNO
NON CONTIENE PARTI CHE L’UTENTE POSSA RIPARARE. RIVOLGERSI A TECNICI DI
ASSISTENZA QUALIFICATI.

PER EVITARE IL RISCHIO DI INCENDI O SHOCK, NON ESPORRE L’APPARECCHIO ALLA
PIOGGIA O ALL’UMIDITÀ.

NON INSTALLARE IL PRODOTTO IN AREE A RISCHIO, NELLE QUALI SONO IMMAGAZZINATI O
UTILIZZATI MATERIALI ALTAMENTE INFIAMMABILI O ESPLOSIVI.

L’APPARECCHIO CUI QUESTO MANUALE SI RIFERISCE È DESTINATO ALL’USO IN
INSTALLAZIONI GENERICHE PER TV A CIRCUITO CHIUSO E NON HA ALCUNA ALTRA
FUNZIONE. NON SUPERARE I LIMITI DI VOLTAGGIO E TEMPERATURA INDICATI NELLE
SPECIFICHE. USARE L’APPARECCHIO ESCLUSIVAMENTE IN AMBIENTI PULITI, NON UMIDI E
NON POLVEROSI.

PRIMA DI PROCEDERE ALLA PULIZIA DELL’APPARECCHIATURA, ISOLARE L’UNITÀ.
UTILIZZARE UN PANNO ASCIUTTO E NON SFILACCIABILE. NON UTILIZZARE DETERGENTI O
SOLVENTI.

IL SEGNALE CHE RAFFIGURA UN LAMPO CON UN'ESTREMITÀ A FORMA DI FRECCIA
ALL'INTERNO DI UN TRIANGOLO EQUILATERO AVVISA DELLA PRESENZA DI UN RISCHIO DI
SHOCK NEL PERIMETRO DEL PRODOTTO.

ATTENZIONE: Si tratta di un prodotto di classe A. In un ambiente domestico il prodotto può causare interferenze

radio nel cui caso potrebbe essere richiesto all’utente di adottare misure adeguate.

Emissioni in radiofrequenza

Regolamento della Federal Communications Commission (FCC) Parte 15.
Standard britannico BSEN55022:1998 per i limiti e i metodi di misurazione delle interferenze radio caratteristiche

delle apparecchiature informatiche.

Sicurezza elettrica

Standard britannico BSEN60950:1999 per la sicurezza delle apparecchiature informatiche, incluse le
apparecchiature elettriche aziendali.

Immunità

Standard britannico BSEN50130-4 per i sistemi di allarme, parte 4, standard di compatibilità elettromagnetica
per la tipologia di prodotti: requisiti di immunità per sistemi di allarme antincendio, anti-intrusione e di tipo
sociale.

Dichiarazione di conformità UE

In base agli standard UE summenzionati, è stata emessa una Dichiarazione di conformità che è archiviata
nella sede del produttore.

Il produttore dichiara che l’apparecchiatura fornita è conforme a quanto previsto dalla direttiva sulla compatibilità
elettromagnetica 89/336 CEE, e da tutte le successive modifiche, dalla direttiva sulle apparecchiature a basso
voltaggio 73/23 CEE.

Regolamenti

Questo dispositivo è conforme alla parte 15 dei regolamenti FCC. Il suo funzionamento è soggetto alle due
condizioni indicate di seguito: (1) il dispositivo non deve causare interferenze pericolose; (2) il dispositivo deve
essere in grado di funzionare anche in presenza di interferenze che possono causare un funzionamento anomalo.

vi

Keyboard Installation and Operation

CON EL FIN DE REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, ABSTÉNGASE DE RETIRAR
LA CUBIERTA, YA QUE EN SU INTERIOR NO HAY NINGÚN COMPONENTE QUE PUEDA SER
REPARADO POR EL USUARIO. EN EL CASO DE QUE SEA NECESARIO, ACUDA A PERSONAL
DE SERVICIO CUALIFICADO PARA QUE REALICE LA REPARACIÓN.

NO EXPONGA ESTE DISPOSITIVO A LA LLUVIA O LA HUMEDAD.

NO INSTALE ESTE PRODUCTO EN ÁREAS PELIGROSAS EN LAS QUE HAYA ALMACENADAS
O SE UTILICEN PRODUCTOS ALTAMENTE INFLAMABLES O EXPLOSIVOS.

EL EQUIPO SUMINISTRADO CON ESTE MANUAL ESTÁ DISEÑADO PARA SU UTILIZACIÓN
EN UNA INSTALACIÓN DE CIRCUITO CERRADO DE TELEVISIÓN (CCTV) Y NO TIENE
NINGUNA OTRA FUNCIÓN. NO SUPERE LOS LÍMITES DE TENSIÓN Y TEMPERATURA
INDICADOS EN LAS ESPECIFICACIONES. UTILICE EL TECLADO MP100CC EXCLUSIVAMENTE
EN UN ENTORNO LIMPIO, SECO Y LIBRE DE POLVO.

ANTES DE LIMPIARLO, AÍSLE LA UNIDAD. UTILICE UN PAÑO SECO Y SIN PELUSAS. NO
UTILICE LÍQUIDOS LIMPIADORES NI DISOLVENTES.

EL SÍMBOLO DE RAYO/PUNTA DE FLECHA RODEADO POR UN TRIÁNGULO EQUILÁTERO
AVISA AL USUARIO DE LA EXISTENCIA DE PELIGRO DE ELECTROCUCIÓN EN EL INTERIOR

DE LA CARCASA DEL PRODUCTO.

PRECAUCIÓN: Este es un producto de Clase A. En entornos domésticos, este producto puede provocar
interferencias de radio, en cuyo caso es posible que el usuario deba adoptar las medidas correctoras oportunas.

Emisión de radiofrecuencia

Parte 15 del Código normativo federal de la Comisión Federal de comunicaciones (Federal Communications
Commission, EE UU).

British Standard BSEN55022:1998 Límites y métodos de medición de características de interferencias de
radio para equipos informáticos.

Seguridad eléctrica

British Standard BSEN60950:1999 Seguridad de equipos informáticos, incluidos equipos eléctricos de uso
empresarial.

Inmunidad

British Standard BSEN50130-4, Parte 4 de sistemas de alarma (Alarm Systems), estándar de compatibilidad
electromagnética para familia de productos: Requisitos de inmunidad para componentes de sistemas de alarma
antiincendios, contra intrusión y sociales.

Declaración de conformidad de la UE

Se ha realizado la Declaración de conformidad en cumplimiento de las normas de la UE indicadas más arriba.
El fabricante es el depositario de dicha declaración.

El fabricante declara que el producto suministrado con esta documentación cumple las normas estipuladas
por la Directiva sobre EMC 89/336 CEE y sus correspondientes enmiendas y la Directiva sobre baja tensión
LVD 73/23 CEE.

Avisos sobre cumplimiento de la legislación

Este dispositivo cumple la parte 15 de las normas de la FCC. Su utilización está sujeta a las siguientes dos
condiciones: (1) Este equipo no puede provocar interferencias nocivas, y (2) este equipo debe aceptar cualquier
interferencia recibida, incluidas las interferencias que puedan provocar un funcionamiento no deseado.

vii

ADCC0200 and ADCC0300

OM DE KANS OP ELEKTRISCHE SCHOKKEN TE VERMIJDEN, DIENT U DE KAP NIET TE
VERWIJDEREN. HET APPARAAT BEVAT GEEN ONDERDELEN DIE DOOR DE GEBRUIKER
KUNNEN WORDEN GEREPAREERD. LAAT ONDERHOUD UITVOEREN DOOR
GEKWALIFICEERD ONDERHOUDSPERSONEEL.

OM DE KANS OP BRAND OF ELEKTRISCHE SCHOKKEN TE VERMIJDEN, DIENT U DIT
APPARAAT NIET AAN REGEN OF VOCHT BLOOT TE STELLEN.

INSTALLEER DIT PRODUCT NIET IN GEVAARLIJKE OMGEVINGEN WAAR ONTBRANDINGS­OF ONTPLOFFINGSGEVOELIGE STOFFEN STAAN OPGESLAGEN OF WORDEN GEBRUIKT.

DE BIJ DEZE HANDLEIDING GELEVERDE APPARATUUR IS ONTWORPEN VOOR GEBRUIK
IN ALGEMENE CCTV-INSTALLATIES EN HEEFT VERDER GEEN ANDERE FUNCTIE. STEL DE
APPARATUUR NIET BLOOT AAN VOLTAGES EN TEMPERATUREN BOVEN DE AANGEGEVEN
LIMIET. GEBRUIK UW MATRIX ALLEEN IN EEN SCHONE, DROGE, STOFVRIJE OMGEVING.

ISOLEER HET APPARAAT VOORDAT U SCHOONMAAKWERKZAAMHEDEN UITVOERT.
GEBRUIK DAARVOOR ALLEEN EEN DROGE, VILTVRIJE DOEK. GEBRUIK GEEN VLOEIBARE
SCHOONMAAKMIDDELEN OF OPLOSMIDDELEN.

HET BLIKSEMSCHICHTSYMBOOL IN DE GELIJKZIJDIGE DRIEHOEK ATTENDEERT DE
GEBRUIKER OP DE KANS OP ELEKTRISCHE SCHOKKEN BINNEN DE BESCHERMENDE KAST.

LET OP: Dit is een A-klasse product. In woonomgevingen kan dit product tot radiostoring leiden en dient de
gebruiker passende maatregelen te nemen.

Radiofrequentie-emissie

Federale voorschriften van de Federale communicatiecommisie (Federal Communications Commission Code of
federal regulations), deel 15.

BSEN55022:1998 Limieten en methoden van meting van radiostoringskenmerken van IT-apparatuur.

Elektrische veiligheid

Britse norm BSEN60950:2000, veiligheid van IT-apparatuur, waaronder zakelijke elektrische apparatuur.

Immuniteit

Britse norm BSEN 50130-4 Alarmsystemen, deel 4, Elektromagnetische compatibiliteit. Productfamilienorm:
immuniteitseisen die worden gesteld aan onderdelen van brand-, inbraak- en persoonlijk-alarmssystemen

Conformiteitsverklaring van de fabrikant

Er bestaat een “conformiteitsverklaring” die conform is met de bovenvermelde EU-normen en de fabrikant
bezit hiervan een exemplaar.

De fabrikant verklaart dat het bij dit document meegeleverde product voldoet aan de voorwaarden van EMC­richtlijn 89/336 EEC en alle aanverwante wijzigingen, Laagspanningsrichtlijn LVD 73/23 EEC.

Gebruiksvoorschriften

Dit apparaat voldoet aan deel 15 van de FCC-regelgeving. Gebruik is onderhevig aan de twee onderstaande
bepalingen: (1) het apparaat mag geen schadelijke storingen veroorzaken, en (2) het apparaat dient bestand te
zijn tegen schadelijke storingen die tot onjuiste werking leiden.

viii

Keyboard Installation and Operation

CHAPTER 1: ABOUT THE ADCC0200 AND ADCC0300 KEYBOARD .................................................. 3

Key Features ....................................................................................................................................... 3

ADCC0200 and ADCC0300 Keyboard Overview ................................................................................4

Feature Quick Reference .................................................................................................................... 7

CHAPTER 2: CONNECTION AND SETUP ............................................................................................ 11

Ancillary Equipment ........................................................................................................................... 11

MP-KMI Keyboard Matrix Interface .............................................................................................. 11

Installation Precautions .....................................................................................................................12

Connections for Cable Distance of Greater than Seven Feet (RS232 Mode) .............................12

Connections for Cable Distance of Seven Feet or Less (RS232 Mode)...................................... 13

Multiple Keyboards on an RS485 Network .................................................................................. 14

Terminating/Biasing the RS485 Network ..................................................................................... 14

Multiple Keyboards on an RS232 Network .................................................................................. 15

CHAPTER 3: BASIC OPERATIONS - OPERATE MODE (ADCC0200 AND ADCC0300) .................... 16

User Numbers and Passcodes.......................................................................................................... 16

Logging On to the System ................................................................................................................. 16

Logging Off from the System .............................................................................................................16

Keyboard Display .............................................................................................................................. 17

Selecting Monitors ............................................................................................................................. 17

Calling a Camera to View on a Monitor ............................................................................................. 17

Controlling a Camera’s Pan, Tilt and Zoom ...................................................................................... 18

Controlling Camera Focus ................................................................................................................. 19

Controlling the Camera Iris ................................................................................................................ 19

Controlling Camera Flip ..................................................................................................................... 19

Auto Iris .............................................................................................................................................19

Auto Focus ........................................................................................................................................ 20

Calling Presets .................................................................................................................................. 20

Running Patterns ...............................................................................................................................21

Dome Camera DirectSet ................................................................................................................... 21

Running Tours ................................................................................................................................... 22

Holding a Tour .............................................................................................................................. 22

Restarting a Tour on Hold ............................................................................................................ 22

Stepping through a Tour ...............................................................................................................22

Reversing a Tour .......................................................................................................................... 23

Stopping a Tour ............................................................................................................................ 23

Calling Salvos (RS232 only) .............................................................................................................. 23

Calling Views (RS485 only) ...............................................................................................................24

Acknowledging Alarms ...................................................................................................................... 24

Auxiliaries .......................................................................................................................................... 24

Setting the Keyboard Display Contrast ............................................................................................. 25

Enabling or Disabling the Keyboard Sounder ...................................................................................25

Viewing Satellite Sites .......................................................................................................................25

Operating a VCR or Digital Recorder ................................................................................................26

Cancel VCR/DVR mode ...............................................................................................................26

Locking and Unlocking a Camera (RS232 only) ...............................................................................26

Telemetry Enable/Disable (RS485 only)............................................................................................ 27

Initiating F1 Key Commands (RS232 only) .......................................................................................27

1

ADCC0200 and ADCC0300

CHAPTER 4: PROGRAMMING WITH THE ADCC0200/ADCC0300 KEYBOARDS ............................ 28

Entering Program Mode (RS232 only) ..............................................................................................28

Exiting Program Mode (RS232 only) .................................................................................................28

Matrix Menu ....................................................................................................................................... 29

Dome Menu Functions ...................................................................................................................... 30

Navigating Dome Camera Menus ..................................................................................................... 30

Setting Presets ..................................................................................................................................31

Programming Dome Patterns ............................................................................................................ 31

Defining Patterns ......................................................................................................................... 31

Clearing Patterns .........................................................................................................................32

Initiating F2 Key Commands (RS232 only) .......................................................................................32

CHAPTER 5: INSTALLER FUNCTIONS ................................................................................................33

Entering the Special Configuration Menu ..........................................................................................33

Setting the Keyboard Address........................................................................................................... 33

Setting the Number of Keyboard Retries........................................................................................... 33

Setting the Network Timeout Period ..................................................................................................34

Setting the Baud Rate ....................................................................................................................... 34

Disabling/Enabling the Sounder ........................................................................................................ 35

Selecting RS485 or RS232 mode ..................................................................................................... 35

To Reset the Keyboard to its Factory Defaults .................................................................................. 35

Selecting Auto Repeat or Make/Break Keypress Mode ....................................................................35

Setting the Passcode (Program Lock) Function................................................................................ 36

APPENDIX A: ADCC0200/ADCC0300 VCR REPROGRAMMING ........................................................37

APPENDIX B: MONITOR ARMING COMMANDS .................................................................................39

APPENDIX C: TROUBLESHOOTING ................................................................................................... 40

APPENDIX D: SPECIFICATIONS ..........................................................................................................41

INDEX .....................................................................................................................................................42

2

Keyboard Installation and Operation

Chapter 1: About the ADCC0200 and ADCC0300 Keyboard

This chapter describes the features of the ADCC0200/ADCC0300 keyboard. It also
describes the location and function of the keyboard's front panel components

Key Features

The ADCC0200/ADCC0300 is a video control station that is fully compatible with the
American Dynamics MegaPower family of matrix switchers. The ADCC0200/ADCC0300
enables the user to view and control cameras and video recorders at local and remote
facilities, and to control auxiliary devices such as door locks and lights. Additionally, the
operator can acknowledge alarms with the unit. These operations are accomplished in
the keyboard's

Operators with key privileges can also perform programming functions using the ADCC0300
keyboard. These functions include programming of presets (targets), patterns, tours, menu
access and dome menu access. These functions are accomplished in

A summary listing of the ADCC0200/ADCC0300 features follows:

Operator

mode.

Program

mode.

• user ID Entry

•

site ID

•

monitor/camera selection

•

pan/tilt and lens control

control through joystick positioning. Zoom, focus, and iris adjustments through
lens control keys

•

“Flip” push-button

•

tour functions

•

salvo functions

(RS232 mode only)

•

view functions

•

alarm functions

acknowledgment

•

pattern and preset functions

display of patterns and presets

•

selectable baud rate

•

adjustable display brightness/contrast

•

Auto Focus/Auto Iris capability

units

•

Camera Lockout

user already has under control

- provides passcode logon/logoff capability

- selects a site for satellite switching

- provides selection for viewing and control

- pan and tilt, or pan, tilt, and zoom (ADCC0300 only)

- enables user to flip cameras 180º from established position

- enables the running and control of camera sequences

- enables the simultaneous call-up of multiple camera scenes

- enables the simultaneous call-up of a specific camera and preset

- supports monitor alarm arming, disarming, and alarm

- enables programming (ADCC0300 only) and

- 1200, 4800, 9600, 19,200, 38,400, 57,600 bps

- supported when used with SpeedDome Ultra

– prevents other users from controlling a camera that the current

•

DirectSet feature

- allows some dome functions to be quickly accessed

3

ADCC0200 and ADCC0300

ADCC0200 and ADCC0300 Keyboard Overview

The keyboard consists of the following elements:

1. Clear key - clears any numerical data entered during camera, monitor selection

etc. Used to backstep or exit the menu system.

2. Menu key - used to enter the matrix menu system.

3. View key - used to call views.

4. Tour/Sequence key - used to call a sequence.

5. Shift key - when held down, allows multiple use of other keys.

6. Pattern key - used to call patterns.

7. Preset key - used to call and program presets.

8. Unit select key - calls control of the target matrix to the keyboard.

9. Function key - used in conjunction with other keys to modify their action.

10. LCD Display - displays system information, such as the currently selected

monitor or camera.

4

Keyboard Installation and Operation

11. Numeric keypad - keys ranging from 0 to 9 that enable the user to select specific

cameras, monitors, presets, sequences, etc.

12. Monitor key - selects the monitor whose number was entered on the numeric

keypad.

13. Camera key - selects the camera whose number was entered on the numeric

keypad.

14. Alarm acknowledge key - acknowledges/clears an alarm displayed on the

currently active monitor.

15. Focus Near/Focus Far Key - adjusts the lens focus for the selected camera.

16. Open/Close Iris Key - opens or closes the lens iris for the selected camera.

17. Zoom In/Zoom Out Key - zoom in or zoom out with the selected camera.

18. Search key - places a DVR into search mode.

19. Telemetry enable/disable key - allows telemetry control (note, when the joystick

is moved, the keyboard automatically enters telemetry mode).

20. Reverse play key - places a VCR/DVR into reverse play mode.

21. Pause key - places a VCR/DVR into pause.

22. Direct Control key - calls a VCR/DVR to control.

23. Rewind key - places a VCR/DVR into rewind.

24. Fast forward key - places a VCR/DVR into fast forward.

25. Joystick

ADCC0200

ADCC0300

2-axis joystick enables the user to pan and tilt, the selected camera.

3-axis joystick enables the user to pan, tilt and zoom the selected

camera.

26. Enter key - used when in program mode.

27. Record key - places a VCR/DVR into record mode.

28. Stop key - stops playback of a VCR/DVR.

29. Start key - starts playback of a VCR/DVR.

30. Auxiliary 1 key - toggles auxiliary 1 between ON state and OFF state.

31. Auxiliary 3 key - toggles auxiliary 3 between ON state and OFF state.

32. Autopan key - starts autopan function for the selected camera (if function is

available).

5

ADCC0200 and ADCC0300

33. Auxiliary key - toggles auxiliary between ON state and OFF state (if function is

available).

34. Flip key - automatically turns the selected dome through 180O.

35. Auxiliary 2 key - toggles auxiliary 2 between ON state and OFF state.

36. Auxiliary 4 key - In RS485 mode, momentarily switches auxiliary 4 from its OFF

state to its ON state for the period the key is held down. In RS232 mode, toggles
auxiliary 4 between ON state and OFF state.

37. Last/Decrement key - in Tour hold mode, steps backwards through the tour. In

VCR mode, reduces playback or record speed.

38. F1/F2 key - this key is reserved for future use.

39. Next/Increment key - in Tour hold mode, steps forwards through the tour. In VCR

mode, increases playback or record speed.

40. DirectSet key - allows dome features for the Baxall Pro-Dome to be called to the

keyboard.

41. Multiscreen key - toggles the multiple picture display on a multiplexer.

42. Freeze key - electronically freezes the picture on a multiplexer.

43. Print key - this key is reserved for future use.

44. Search key - access the search facility on a multiplexer.

45. Connection port - used to connect power to the ZKX72J/ZKX73J, and data to a

switching system.

46. Termination/Biasing switches - used to terminate and/or bias an RS485

network.network.

6

Keyboard Installation and Operation

Feature Quick Reference

The features that are available depend on the keyboard in use (ADCC0200 or ADCC0300) and the
communication format that is utilized (RS232 or RS485).

Standard Matrix Operations

FEATURE KEYBOARD COMMAND ADCC0200 ADCC0300

RS485 RS232 RS485 RS232

Select Monitor Monitor number → 
Select Camera Camera number → 
Select Matrix/Site Site number → AND 
Telemetry Enable/Disable 
Pan Left/Right Joystick Left/Right 
Tilt Up/Down Joystick Up/Down 
Zoom In (or Twist Joystick Clockwise) 
Zoom Out (or Twist Joystick Anti-CW) 
Focus Near 
Focus Far 
Iris Open 
Iris Close 
Flip 
Engage Auto Iris AND , , or 
Engage Auto Focus AND , , or 
Select Preset Preset number → 
Record Preset → Preset number → 
Acknowledge Alarm 
Select Sequence Sequence number → 
Select View View number → AND 
Select Salvo Salvo number → AND 

7

ADCC0200 and ADCC0300

Standard Matrix Operations (continued)

FEATURE KEYBOARD COMMAND ADCC0200 ADCC0300

RS485 RS232 RS485 RS232

Run Tour Tour number → 
Hold Tour AND 
Restart Current Tour 
Last and Next Camera or 

(When Tour Held)
F1 Function Function number → 

F2 Function

Function number → AND



Matrix Menu Operations

FEATURE KEYBOARD COMMAND ADCC0200 ADCC0300

RS485 RS232 RS485 RS232

Enter Menu Mode AND 
Move Cursor Up Joystick Up 
Move Cursor Down Joystick Down 
Move Cursor Left Joystick Left 
Move Cursor Right Joystick Right 
Page Up (if available) AND Joystick Up 
Page Down (if available) AND Joystick Down 
Page Left (if available) AND Joystick Left 
Page Right (if available) AND Joystick Right 
Menu Select ENTER key 
Menu Escape RS232: AND -  - 

RS485:  -  -

8

Keyboard Installation and Operation

Dome Operations

FEATURE KEYBOARD COMMAND ADCC0200 ADCC0300

RS485 RS232 RS485 RS232

Enter Dome Menu Mode → AND 
Exit Dome Menu Mode Via Dome Menu 
Scroll Up Dome Menu Joystick Up 
Scroll Down Dome Menu Joystick Down 
Scroll Left in Dome Menu Joystick Left 
Scroll Right in Dome Menu Joystick Right 
Cycle Field Options/Values or (or Twist Joystick) 
Enter Selection or 
Program Pattern → Pattern number → 

AND → Move joystick as
required → Pattern number

→

Run Pattern Continuous Pattern number + AND 
Aux 1 On/Off 
Aux 2 On/Off 
Aux 3 On/Off 
Aux 4 On/Off Aux 4 Aux 4 

Lock/Unlock AND 

9

momentary momentary

ADCC0200 and ADCC0300

VCR (PIP) / Direct Control Mode (All Functions Available in Direct Control Mode)

FEATURE KEYBOARD COMMAND ADCC0200 ADCC0300

RS485 RS232 RS485 RS232

Select VCR Mode RS232: VCR number → -  - 

RS485:  -  -

Play 
Stop 
Rewind 
Fast Forward 
Record 
Pause 
Reverse Play 
Search 
Menu 
Enter ENTER key 
Increment/Decrement or 

Record or Playback Speed
Up Joystick Up 

Down Joystick Down 
Left Joystick Left 
Right Joystick Right 

DirectSet Feature

FEATURE KEYBOARD COMMAND ADCC0200 ADCC0300

RS485 RS232 RS485 RS232

Initiate DirectSet 

10

Chapter 2: Connection and Setup

This chapter describes the power and data connections between the ADCC0200/
ADCC0300 keyboard and the switching system being used.

IMPORTANT NOTE

The default setting for the keyboard is RS485 mode at 19200 baud. To change these
settings, enter the Special Config menu by pressing SHIFT (
within five seconds of powering up the keyboard. Then press one of the following:

to change baud rate.
to change the mode (ADNet RS485, RS232).

to select Auto Repeat or Make/Break mode. See the matrix manual for correct setting.

to enable/disable the speaker.

For other functions, please see Chapter 5.

Ancillary Equipment

The keyboard is supplied with one seven foot (2 meters) MP-CBL data connection cable.
The MP-KMI keyboard matrix interface (optional) is also supplied with a MP-CBL data
connection cable.

The power supply is connected to the jack connector of the MP-KMI keyboard matrix
interface. The power supply must be a Class 2 type UL listed 12V DC component.

Keyboard Installation and Operation

) and CLEAR ( ) keys

MP-KMI Keyboard Matrix Interface

The MP-KMI keyboard matrix interface contains two RJ-45 connectors connected to a
five-way screw terminal block. The Matrix connector is connected to the switching system
and the Keyboard connector to the keyboard using the MP-CBL cable supplied.

Power is supplied to the keyboard via the power connector built in to the MP-KMI.

The power supply is limited to
15W by a 500mA UL listed fuse.

11

ADCC0200 and ADCC0300

Installation Precautions

This installation should only be carried out by qualified personnel, and should conform to
all local electrical codes. Safeguards should be taken to avoid unintentional operation by
employees and maintenance personnel working about the premises, by falling objects,
by customers, by building vibration, and by similar causes.

CAUTION: DO NOT CONNECT THE POWER SUPPLY UNTIL ALL CONNECTIONS

Connections for Cable Distance of Greater than Seven Feet (RS232 Mode)

For installations where the keyboard-to-system cable distance is greater than seven feet
(2.0 metres), the following additional components are required:

• Two MP-KMI wall-mount keyboard network interfaces

• A single pair 22 AWG shielded with drain wire and Belden 8761 cable - supplied by
installer

Connect the cables in accordance with the following figure.

HAVE BEEN VERIFIED

Note - Other Network Connections

For other connection to MP-LT and other network equipment, please consult the appropriate
installation and operation handbook.

12

Keyboard Installation and Operation

Connections for Cable Distance of Seven Feet or Less (RS232 Mode)

For installations where the keyboard-to-system cable distance is seven feet or less, connect
the cables in accordance with the figures below.

The RJ-45 socket on the MP-KMI that is marked Matrix is connected to the switching
system. The RJ-45 connector on the MP-KMI marked Keyboard is connected to the
keyboard using the MP-CBL cable supplied with the keyboard.

Note - Other Network Connections

For other connection to MP-LT and other network equipment, please consult the appropriate
installation and operation handbook.

13

ADCC0200 and ADCC0300

Multiple Keyboards on an RS485 Network

A maximum of 16 devices may be connected when working in RS485 mode. A maximum
of eight keyboards can be assigned to the system.

For correct connection of multiple keyboards to an MegaPower LT, please see the
MegaPower LT Installation and Operation Handbook.

Terminating/Biasing the RS485 Network

The keyboard has built in RS485 network termination and/or biasing. For most small to
medium sized installations, it should not be necessary to change the switches from their
default settings. Only for large installations should your network require biasing and/or
terminating. The switches are shown below for your reference. The default setting for
switches 1, 2 and 3 is OFF (UP). Switch 4 is not used.

Network setting Switch 1 Switch 2

Biased ON ON
Not Biased* OFF* OFF*

*Default setting

Network setting Switch 3

Terminated ON
Not Terminated* OFF*

*Default setting

14

Keyboard Installation and Operation

Multiple Keyboards on an RS232 Network

Use the following diagram as guidance to connect multiple RS232 keyboards via a port
expander. The following rules must be observed:

1. A maximum of four RS232 keyboards can be connected to the network.

2. The distance between two system components should not exceed 50 feet/15
meters.

3. All cables are to be screened/shielded Cat 5 or better.

4. Keyboards require a separate power supply via a MP-KMI.

Note

For correct connection of multiple keyboards to an MegaPower LT, please see the
MegaPower LT Installation and Operation Handbook.

15

ADCC0200 and ADCC0300

Chapter 3: Basic Operations - Operate Mode (ADCC0200 and ADCC0300)

This chapter describes basic keyboard operations such as calling cameras to view on
monitors, running tours, patterns, presets, macros and salvos. It also explains menu
navigation and camera functions such as how to pan, tilt and zoom cameras, and how to
control lens functions. In addition, procedures are provided for acknowledging alarms
and controlling the various VCR functions.

User Numbers and Passcodes

Depending on the setup of the switching system being used, an operator may have to
enter a user code and passcode on the keyboard in order to gain system access. If a user
code is required, the word "USERCODE" appear on the LCD to prompt the operator. After
entering the appropriate user code, the operator is prompted by the word "PASSCODE"
on the display. After entering the appropriate passcode, the operator has system access.

Logging On to the System

To log on to the system:

1. Enter your user code (assigned by the system administrator) on the numeric
keypad.

2. Press the ENTER key

The system prompts for the user passcode by displaying "PASSCODE" on the LCD display.

3. Enter the assigned passcode (maximum of six digits) on the numeric keypad.

If an incorrect passcode is entered, press the CLEAR (

4. Press the ENTER key.

If the passcode is accepted, the LCD display will be similar to that shown below. This
confirms that the keyboard is communicating with the system, and that a monitor can be
called to the keyboard.

Logging Off from the System

When a user shift is completed, it is advisable to log off from the switching system to
insure system security.

To log off from the system:

1. Enter 99 using the numeric keypad and press the F1 (

) key, and then repeat step 3.

S01 M0013 C0001

) key.

16

Keyboard Display

The 16 character, two-line LCD keyboard display shows site, monitor, and camera numbers,
as well as various status messages and numerical data entered by the user. The main
functional areas of the LCD display are shown below.

Note: when running a tour, information about the current camera is shown on the monitor
displaying the tour. Tour information is not shown on the keyboard LCD display.

Selecting Monitors

Workstation monitors display the video from the cameras and domes selected by the
operator. Each monitor has an identification number documented by the system
administrator.

To select a monitor:

1. Enter the monitor identification number on the numeric keypad. The number
entered will appear on the left hand side of the LCD display.

Keyboard Installation and Operation

2. Press the MONITOR (
side of the top line of the LCD display.

) key. The number entered will appear on the right hand

13
S01 M000 C0000

Calling a Camera to View on a Monitor

After a monitor has been called to the control of the keyboard, a camera can be called to
view on the monitor. Each system camera has a unique identification number documented
by the system administrator.

To call a camera:

1. Enter the camera identification number on the numeric keypad. The number
entered will appear on the right hand side of the top line of the LCD display.

2. Press the CAMERA (
the display.

) key. The camera number will appear next to the "C" on

S01 M000 C0000

17

ADCC0200 and ADCC0300

32

S01 M013 C0000

The selected video input will now appear on the monitor screen. After calling a camera to
the selected monitor, any other camera can be called to the monitor by repeating the two
steps above.

Controlling a Camera’s Pan, Tilt and Zoom

Once an appropriately equipped camera has been called to view on a monitor, the operator
can manually control the camera's movement.
camera.

The joystick controls the panning and tilting of cameras connected to the switching matrix.
As the joystick is moved to the left or right, and is moved towards or away from the
operator, the camera will pan and/or tilt accordingly.

For cameras with variable speed pan/tilt capability, camera movement speed is proportional
to the positioning of the joystick. The further from the stationary centre position the joystick
travels, the faster the camera will move.

Additionally, the ADCC0300 keyboard's 3-axis joystick can control lens
to the apparent action of moving closer to or farther away from an object, as seen through
the camera lens. For cameras equipped with an appropriate zoom lens, the zoom function
can be controlled from the ADCC0300 joystick by twisting it clockwise or counterclockwise.
Twisting clockwise enables the lens to zoom in. Twisting counterclockwise enables the
lens to zoom out.

Center the joystick when the camera has been positioned appropriately.

Tilt

is the up and down movement of the camera.

S01 M013 C0032

Pan

is the side-to-side movement of the

zoom. Zoom

refers

ADCC0200 Joystick ADCC0300 Joystick

18

Controlling Camera Focus

Focus refers to the action of adjusting the clarity of the camera image displayed on the
monitor. To focus the camera on a distant object, press the FAR key. To focus on a closer
object, press the NEAR key.

Controlling the Camera Iris

Normally, the brightness of a picture is controlled by the camera's auto iris or other feature.
However, there may be times when the operator needs the picture on the monitor to
appear lighter or darker. To brighten the picture, press the OPEN iris key. To darken the
picture, press the CLOSE iris key.

Controlling Camera Flip

To "flip" a suitably equipped camera 180O from its current position (for uninterrupted
surveillance of objects which pass directly beneath the camera), use the FLIP key.

To flip the camera:

Keyboard Installation and Operation

Auto Iris

1. Press the FLIP (

Note: on suitably equipped dome cameras with the auto-flip function turned on, the dome
flips automatically when the subject passes directly beneath the camera.

Certain cameras are designed with Auto Iris capability. The feature can be enabled from
the keyboard as follows.

To enable auto iris:

1. Hold down the FUNCTION (

2. Press either the OPEN IRIS/CLOSE IRIS or FOCUS NEAR/FOCUS FAR keys.
Auto-iris operation AND auto-focus operation is enabled.

Note: using the manual OPEN or CLOSE iris key will override the Auto Iris function as
long as either of these keys is held down. The camera may or may not then return to auto
iris mode after a time interval, or it may stay in manual iris mode. This depends on the
camera under control and how the camera has been set up.

) key.

) key.

19

ADCC0200 and ADCC0300

Auto Focus

Certain cameras are designed with Auto Focus capability. The feature can be enabled
from the keyboard as follows.

To enable auto focus:

1. Hold down the FUNCTION (

2. Press either the FOCUS NEAR/FOCUS FAR or OPEN IRIS/CLOSE IRIS keys.

Note: using the manual Focus FAR or Focus NEAR key will override the Auto Focus
function as long as either of these keys is held down. The camera may or may not then
return to auto focus mode after a time interval, or it may stay in manual focus mode. This
depends on the camera under control and how the camera has been set up.

Calling Presets

A preset is a memorized location or scene that a pan/tilt camera can display on operator
demand. Presets are also referred to as
system used, the operator will have the option of calling a certain number of presets, each
with its own unique identification number. Presets are positioned and stored in Program
mode discussed in later chapters of this manual. Once they have been programmed,
presets can be called to view on the selected monitor.

To call a preset:

1. After calling a pan/tilt camera to view, enter the preset identification number using

2. Press the PRESET (

3. The preset number entered at step 1 will remain on the right hand side of the top

) key.

Auto-focus operation AND auto-iris operation is enabled.

shots

or

targets

. Depending on the matrix switching

the numeric keys. The number entered will appear on the right hand side of the
top line of the LCD display.

) key.

line of the LCD display.

1

S01 M001 C0001

The selected video now appears on the monitor with appropriate pan, tilt, zoom, and
focus adjustments.

20

Running Patterns

A pattern is a series of pan, tilt, zoom, and focus commands defined for a dome camera.
A pattern is programmed in real time, which means that the dome remembers each
pattern segment in the actual time it takes the operator to execute a command.

To run a pattern:

1. Call the camera that the pattern will run on.

2. Enter the pattern number using the numeric keys. The number entered will
appear on the right hand side of the top line of the LCD display.

3. Hold down the SHIFT ( ) key and press the PATTERN ( ) key.

Dome Camera DirectSet

The DirectSet feature allows certain dome camera functions to be accessed quickly from
the keyboard. Please note that this feature is not available on some dome cameras or
controller/matrix systems.

To access the DirectSet menu:

1. Call a monitor.

2. Call a suitable dome camera to command of the keyboard.

3. Press the DIRECTSET ( ) key.

The dome camera's DirectSet menu will be displayed on the currently selected monitor.
Note that the menu options shown depend on the dome camera in use.

Keyboard Installation and Operation

0 TOGGLE DIRECTSET MENU
1 DOME CONFIG MENU
2 AUTO IRIS/AUTO FOCUS
3 FLIP
4 PEEL PATTERN
10 NIGHT MODE
11 DAY MODE
12 AUTO DAY/NIGHT MODE
13 WDR ON
14 WDR OFF
255 RESET DOME

To call a DirectSet function:

1. Enter the number of the function using the numeric keys.

2. Press the DIRECTSET ( ) key.

For example if a dome flip function was required, enter 3 and press the DIRECTSET key.
If the number for the DirectSet feature is already known to the operator, it can be entered

on the numeric keypad and the DirectSet key pressed directly. It is not necessary to call
the DirectSet feature menu to the monitor.

21

ADCC0200 and ADCC0300

Running Tours

A

tour

is a dynamic sequence of camera views, each of which appears on a selected

monitor screen for a specified

preset

status,

universal tours

To run a tour:

1. Select a monitor.

2. Enter the tour identification number using the numeric keys. The number entered
will appear on the right hand side of the top line of the LCD display.

auxiliary

.

dwell time

status, and

, and each of which can have a pre-programmed

connect next

status. Tours are also referred to as

3. Press the SEQUENCE (

4. The LCD display will show "Sequence
is the tour identification number entered in step 2 above). Whilst the tour is
running, the monitor will show the cameras and views comprising the tour e.g.
C0023, C0012, C0003, C0023, V001, V124.

Note: when running a tour, information about the current camera is shown on the monitor
displaying the tour. Tour information is not shown on the keyboard LCD display.

) key.

= n"

for approximately 5 seconds (where

n

Holding a Tour

A tour can be stopped and held on a single camera entry. While a tour is on hold, all
keyboard control actions (pan, tilt, lens adjustment, auxiliary on/off functions) can be
performed on the held camera.

To hold a tour:

1. Hold down the SHIFT (

) key and press the SEQUENCE ( ) key.

Restarting a Tour on Hold

To restart a held tour, press the SEQUENCE ( ) key. The tour will continue running from
the point at which it was previously held.

Stepping through a Tour

When a tour is held, the LAST ( ) and NEXT ( ) keys can be used to step through the
tour.

To step through a tour:

1. To step forward press the NEXT (

2. To step backward, press the LAST ( ) key.

) key.

22

Keyboard Installation and Operation

Reversing a Tour

When a tour is running, the NEXT ( ) and LAST ( ) keys can be used to reverse the
direction of a tour.

To reverse the direction of a tour:

1. Press the LAST (
(

) key once.

Stopping a Tour

A running system or scratch-pad tour can be stopped by calling a camera to be displayed
on the selected monitor.

Calling Salvos (RS232 only)

A

salvo

is the simultaneous display of multiple camera scenes on a group of numerically
contiguous monitors. The number of salvo entries allowed is dependant on the matrix
switching system being used. Each system salvo has a unique identification number that
defines the set of contiguous monitors.

To call a salvo:

1. Enter the identification number of the first (lowest numbered) monitor of the

contiguous monitor group on the numeric keypad. The number entered will
appear on the right hand side of the top line of the LCD display.

2. Press the MONITOR (

3. Enter the identification number for the salvo. The number entered will appear on

the right hand side of the LCD display.

) key once. Note, to again reverse the tour, press the NEXT

) key.

1

S01 M013 V0001

4. Hold down the SHIFT (

5. The salvo will be displayed on the contiguous set of monitors.

Note the "C" in the bottom line of the LCD display will change to "V" while the salvo is
running.

) key and press the MONITOR ( ) key.

23

ADCC0200 and ADCC0300

Calling Views (RS485 only)

A

view

is the simultaneous display of a specific preset position on a specific camera.

To call a view:

1. Enter the view number using the numeric keys. The number entered will appear
on the right hand side of the top line of the LCD display.

2. Hold down the SHIFT (

Acknowledging Alarms

When a monitor is armed for an alarm contact, the video input associated with that alarm
contact is displayed on the monitor when the alarm is activated. If the monitor is armed for
manual clearance, any alarm displayed on the monitor can be acknowledged (cleared)
by the operator.

To acknowledge an alarm:

1. Call the monitor that is displaying the alarm video.

2. Press the ALARM (

If the monitor is sequencing multiple alarms, step through to the appropriate alarmed
video input by first pressing the SHIFT ( ) and SEQUENCE ( ) keys to hold the
sequence, and then by using the LAST/NEXT keys. Press the ALARM ( ) key to
acknowledge the alarm. Continue to step to and acknowledge each alarm until all the
appropriate alarms have been cleared.

Alarm signalling capability will vary depending on which switching system is connected to
the keyboard. Consult the switching system's documentation to determine the particulars
of the alarm interface.

Auxiliaries

An auxiliary is a relay that switches devices such as camera lights, a camera washer, and
a camera wiper, on or off. The keyboard can control four auxiliaries labelled AUX 1,
AUX 2, AUX 3, and AUX 4.

In RS232 mode, all the auxiliaries have a latching operation—that is the auxiliary will
remain ON until the key is again pressed. In RS485 mode, AUX 4 has a momentary
operation—that is it will remain ON whilst the key is held down. LEDs adjacent to each
auxiliary show whether it is currently ON or OFF.

) key and press the VIEW ( ) key.

) key.

24

Setting the Keyboard Display Contrast

1. Press the FUNCTION ( ) and MENU ( ) key.

2. Use the Focus NEAR/Focus FAR key to increase/decrease the display's contrast.

3. When the contrast is satisfactory, press the ENTER key.

Enabling or Disabling the Keyboard Sounder

In the default (factory) setting mode, the keyboard's sounder sounds each time a key is
pressed.

To enable/disable the keyboard sounder:

Keyboard Installation and Operation

1. Press the FUNCTION (
enabled and disabled.

Viewing Satellite Sites

A

site

is a complete matrix switcher/controller system, providing both local and remote
control of resources in a satellite network. If your workstation supports satellite site switching
capabilities, this function accesses satellite sites.

To gain access to a satellite site:

1. Enter the site number on the numeric keypad. The number entered will appear on

the right hand side of the top line of the LCD display.

2. Hold down the SHIFT (

site number will appear next to "S" on the LCD display.

It is now possible to call remote site monitors and cameras by the procedures discussed
earlier in this chapter.

) and ENTER key to toggle the sounder between

) key and press the SITE SELECT ( ) key. The new

S03 M0001 C0001

25

ADCC0200 and ADCC0300

Operating a VCR or Digital Recorder

To initiate VCR control, the operator performs the following actions:

1. Enter the number of the VCR/DVR using the numeric keys.

2. Press the VCR SELECT ( ) key.
The VCR/DVR number will be shown in the top line of the display in the format R

R0021

S01 M013 C0001

The keyboard's VCR keys can now be used to control the selected VCR/DVR.

Cancel VCR/DVR mode

To Cancel VCR mode:

nnnn.

1. Press the VCR SELECT (

) key.

Locking and Unlocking a Camera (RS232 only)

Operators can lock and unlock the telemetry control of a camera to prevent other operators
from taking control, if for example it was being used to follow a suspect. Note however
that a higher priority user or keyboard will override the lock.

To lock a camera:

1. Enter the camera identification number on the numeric keypad.

2. Hold down the SHIFT (
SHIFT and TELEMETRY again will unlock the camera.

The word "LOCKED" will be displayed in the keyboard's display.

Note the lock function will automatically cancel after 60 seconds of keyboard inactivity, or
when a new camera or monitor is called by the operator.

) key and press the TELEMETRY ( ) key. Pressing

LOCKED
S01 M013 C0001

26

Telemetry Enable/Disable (RS485 only)

To send telemetry commands to cameras, it is necessary to enable telemetry to the selected
camera. The telemetry key has a toggle action.

To enable/disable telemetry:

Keyboard Installation and Operation

1. Press the TELEMETRY (

Note it is not necessary to enable telemetry in order to use the joystick to control the
movement of a camera.

) key. Pressing the key again will disable telemetry.

Initiating F1 Key Commands (RS232 only)

The F1 key on the keyboard is a special function key which, when used with numeric
keyboard inputs, accomplish special functions within a matrix system. Refer to the matrix
documentation for a listing of supported commands.

To perform an F1 function key command:

1. Enter the number for the command using the numeric keys.

2. Press the F1 (

) key.

27

ADCC0200 and ADCC0300

Chapter 4: Programming with the ADCC0200/ADCC0300 Keyboards

This chapter provides step-by-step instructions for programming the keyboard.
Programming operations require the entry of the Program Lock passcode.

IMPORTANT NOTE

In RS232 mode, the ADCC0300 keyboard has programming functionality and is able to
set presets, access matrix menus and dome configuration menus. The ADCC0200
keyboard is an operate-only keyboard in RS232 mode.

Entering Program Mode (RS232 only)

To prevent unauthorised programming of the matrix/switching system, a Program Mode
lock is used. To enter Program mode the Program Lock passcode must be correctly
entered.

To enter the Program Lock passcode:

1. Enter 999 using the numeric keys

2. Press the FUNCTION (

3. At the "Enter Passcode" prompt, use the numeric keys to enter the 4-digit
passcode (1234).

4. Press the ENTER key.

The display will change showing an unlocked padlock icon indicating that Program mode
is available.

) key.

Exiting Program Mode (RS232 only)

This function exits Program mode and reinstates the Program Lock passcode protection
schema.

1. Enter 999 using the numeric keys

2. Press the FUNCTION (

The padlock icon will disappear from the display indicating that Program mode is
unavailable.

) key.

S01 M0001 C0001

28

Matrix Menu

Keyboard Installation and Operation

The keyboard is able to view the main menu of the switching matrix system being used.
To enter matrix menu mode:

1. Hold down the SHIFT (
main menu for the switching matrix system on the currently selected monitor.

Using the ADCC0300 keyboard, the following functions are available:

• Joystick UP - moves cursor up one character

• Joystick DOWN - moves cursor down one character

• Joystick LEFT - moves cursor left one character

• Joystick RIGHT - moves cursor right one character

• SHIFT key + Joystick UP - displays prior menu page up

• SHIFT key + Joystick DOWN - displays next menu page down

• SHIFT key + Joystick LEFT - displays the menu page to the left

• SHIFT key + Joystick RIGHT - displays the menu page to the right

• ENTER key - stores entered menu data

• SHIFT key + CLEAR (
previously displayed screen

Several American Dynamics switching systems provide menu programming for a variety
of functions. Camera groups, system tours, system salvos, alarm contact tables, monitor
arming, and event timers are among the variables that may be defined through menu
programming.

For information about the specific tasks that you can do from the main menu, refer to the
appropriate switching system operating instructions.

) key and press the MENU ( ) key. This will open the

) key - exits the current screen and returns to the

29

ADCC0200 and ADCC0300

Dome Menu Functions

The ADCC0300 keyboard can be used to configure a suitable dome camera by remotely
accessing the dome camera's menu system

To enter the dome camera menu:

1. Call the dome camera to the monitor.

2. Press the FUNCTION (

3. Hold down the SHIFT ( ) key and press the MENU ( ) key. This will open the
main menu for the dome on the currently selected monitor.

Navigating Dome Camera Menus

The ADCC0300 keyboard can be used to navigate through the dome camera's menu
system, and to change parameters for the dome camera.

To navigate the dome camera menu:

• Use joystick up/down movements to choose menu items and menu parameters.

• Use joystick left/right movements to move cursor left/right one character.

• Use joystick clockwise/counterclockwise movements, or the Zoom IN/Zoom OUT
key to change selected parameters.

• Press the Focus FAR/Focus NEAR key to select menu items or parameters.

) key.

30

To exit a dome camera menu:

1. Use the joystick to select QUIT WITHOUT SAVING - this will exit the dome menu

2. Use the joystick to select EXIT AND SAVE CHANGES - this will save any

Setting Presets

Dome, and pan/tilt cameras can be programmed with one or more preset shots.
To program a preset:

1. Call the desired camera to a monitor.

2. Maneuver the camera as required using the keyboard's joystick.

Keyboard Installation and Operation

without saving any changes.

changes and exit the dome menu.

3. Press the FUNCTION (

4. Enter a number for the preset using the numeric keys.

5. Press the PRESET ( ) key.

Programming Dome Patterns

Up to three patterns may be programmed for each programmable dome camera. A pattern
is a predefined sequence of dome movements. The three patterns for a dome can
collectively consist of up to 98 camera commands. A single pattern cannot have a duration
longer than 400 seconds.

Defining Patterns (RS485 only)

To program a pattern:

1. Call the desired dome to a monitor.

2. Maneuver the camera to the position where the pattern will start using the
keyboard's joystick.

3. Press the FUNCTION ( ) key.

4. Enter a number (1 - 3) for the pattern using the numeric keys.

5. Press the PATTERN ( ) key.

6. Maneuver the camera using the joystick to define the pattern.

7. When the pattern movements have been completed, enter the pattern number
using the numeric keys.

) key.

8. Press the FUNCTION ( ) key.

31

ADCC0200 and ADCC0300

Clearing Patterns (RS485 only)

If a dome supports the clear pattern feature, then this operation will delete the programmed
pattern. To clear a pattern:

1. Press the FUNCTION (

2. Enter the pattern number using the numeric keys.

3. Press the PATTERN ( ) key.

4. Enter the pattern number using the numeric keys.

5. Press the FUNCTION ( ) key.

) key.

Defining Patterns (RS232 only)

1. Press the FUNCTION ( ) key.

2. Enter a number (1 - 3) for the pattern using the numeric keys.

3. Press the PATTERN ( ) key

4. Maneuver the camera using the joystick to define the pattern.

5. Press the PATTERN ( ) key

Clearing Patterns (RS232 only)

1. Press the FUNCTION ( ) key.

2. Enter the pattern number using the numeric keys.

3. Press the PATTERN (

4. Press the PATTERN ( ) key to save

) key

Initiating F2 Key Commands (RS232 only)

The Function and F1 keys on the keyboard can be used along with the numeric keyboard
inputs to accomplish special functions within the MegaPower 48 system. Refer to the
MegaPower 48 documentation for a listing of supported commands.

To perform an F2 special function key command:

1. Enter the number for the command using the numeric keys.

2. Hold down the FUNCTION (

3. Press the F1 (

) key.

) key.

32

Chapter 5: Installer Functions

This chapter provides step-by-step instructions for keyboard installer functions. Installer
operations are accessed using the Special Configuration menu.

Entering the Special Configuration Menu

During the first five seconds after the unit is powered up, the display shows the current
software version number, the selected baud rate, etc. Whilst in this state, the Special
Configuration menu may be accessed.

1. During the five seconds after power is connected, simultaneously press the
SHIFT (

2. The LCD will display "Special Config"

) and CLEAR ( ) keys.

Setting the Keyboard Address

1. Enter the Special Config menu.

2. Press the VCR REVERSE PLAY ( ) key.

3. At the "Enter keyboard address" prompt, enter the keyboard address required
(default is 1).

Keyboard Installation and Operation

4. Press ENTER.

Setting the Number of Keyboard Retries

1. Enter the Special Config menu.

2. Press the VCR PAUSE ( ) key.

3. At the "Enter RS485 Retries" prompt, enter the number required (default is 3).

4. Press ENTER.

33

ADCC0200 and ADCC0300

Setting the Network Timeout Period

1. Enter the Special Config menu.

2. Press the VCR SELECT ( ) key.

3. At the "RS485 Timeout" prompt, enter the period required. The number entered is
in units of 5mS e.g. entering 10 will set the timeout period to 50mS.

4. Press ENTER.

Setting the Baud Rate

1. Enter the Special Config menu.

2. Press the VCR REWIND ( ) key.

3. At the "1=RS485 2=RS232" prompt, press 2 and then the ENTER key. It should
be noted that the default is RS485.

4. The display will show:

1=1200 2=4800
0=more..

Pressing the 0 key will change the display to:

3=4800 4=9600
0=more..

Pressing the 0 key again will change the display to:

5=19200 6=38400
0=more..

Pressing the 0 key once more will change the display to:

7=57600
0=more..

5. Press the number key for the desired baud rate. For example, if the required
baud rate is 19200, press the number 5 key, and then the ENTER key.

34

Disabling/Enabling the Sounder

1. Enter the Special Config menu.

2. Press the VCR FAST FORWARD ( ) key.

3. At the "Sound 1=On 2=Off" prompt, enter 1, or 2 and then press the ENTER key.

Selecting RS485 or RS232 mode

1. Enter the Special Config menu.

2. Press the VCR RECORD ( ) key.

3. At the "Set mode 1=RS485 2=RS232" prompt, enter 1, or 2 and then press the
ENTER key.

To Reset the Keyboard to its Factory Defaults

1. Enter the Special Config menu.

Keyboard Installation and Operation

2. Press the VCR PLAY (

3. The unit will display the message "Defaults Loaded".

) key.

Selecting Auto Repeat or Make/Break Keypress Mode

In Auto Repeat mode, RS232 telemetry commands are repeated at 15Hz for as long as
the key is held down or the joystick is not centralised. In Make/Break mode, a single
command is sent upon keypress, and another when the key is released.

1. Enter the Special Config menu.

2. Press the TELEMETRY (

3. At the "Telemetry 1=Rept 2=Mak/Brk" prompt, enter 1, or 2 and then press the
ENTER key.

) key.

35

ADCC0200 and ADCC0300

Setting the Passcode (Program Lock) Function

IMPORTANT - to set the passcode, the keyboard must be in RS232 mode.

1. Enter the Special Config menu.

2. Press the MENU ( ) key.

3. At the "Program Keylock Enter to Enable" prompt, press the ENTER key.

4. The display will show:

1234
Enter Passcode

5. The default passcode is "1234". This can be accepted by simply pressing the
ENTER key. Alternatively, a new 4-digit passcode can be entered using the
numeric keys. To enter a new passcode, enter the number using the numeric
keys, then press the ENTER key.

36

Keyboard Installation and Operation

Appendix A: ADCC0200/ADCC0300 VCR Reprogramming

The ability to reprogram the RS232 commands, that are sent out when the unit is in RS485 mode with Direct Control
enabled, has been added. The default commands are those applicable to the Direct Control and are shown in the
second and third columns below:

Label Key Default Command

PLA Play <STX>FPL<ETX>
REV Reverse <STX>RPL<ETX>
PAU Pause <STX>PAU<ETX>
REW Rewind <STX>REW<ETX>
FWD Fast Forward <STX>FWD<ETX>
REC Record <STX>REC<ETX>
STP Stop <STX>STO<ETX>
DZM Digital Zoom <STX>SEA<ETX>
MEN Menu <STX>MEN<ETX>
INC Increment <STX>ISP<ETX>
DEC Decrement <STX>DSP<ETX>
ENT Enter <STX>ENT<ETX>
JLT Joystick Left <STX>ARL<ETX>
JRT Joystick Right <STX>ARR<ETX>
JUP Joystick Up <STX>ARU<ETX>
JDN Joystick Down <STX>ARD<ETX>
SLO - 0x64
FST - 0x14
PAR Parity Change 8N1

In order to reprogram these commands, the SEARCH ( ) key must be pressed within 5 seconds of entering the
Special Config menu (achieved by simultaneously pressing the SHIFT and CLEAR keys) following a reset.

Note that they may only be reprogrammed if the keyboard is configured for RS485 mode with Direct Control enabled.

Once the above key sequence has been pressed, the reprogramming takes place using a terminal or emulator attached
to the RS232 port of the keyboard (as shown below). The baud rate will be whatever was configured on the keyboard
for RS232 mode (see Setting the Baud Rate on page 34).

37

ADCC0200 and ADCC0300

The following text should initially be shown on the teminal:

PLA 02 46 50 4C 03

REV 02 52 50 4C 03

PAU 02 50 41 55 03

REW 02 52 45 57 03

FWD 02 46 57 44 03

REC 02 52 45 43 03

STP 02 53 54 4F 03

DZM 02 53 45 41 03

MEN 02 4D 45 4E 03

INC 02 49 53 50 03

DEC 02 44 53 50 03

ENT 02 45 4E 54 03

JLT 02 41 52 4C 03

JRT 02 41 52 52 03

JUP 02 41 52 55 03

JDN 02 41 52 44 03

SLO 64

FST 14

Type SAV to save, LST to show list, or enter new mapping (eg PLA 41 03)

This text shows the label associated with each key from the table (e.g. PLA) and the hexadecimal values that will be
transmitted when the corresponding key is pressed.

To reprogram a particular key, simply type the three-character label, followed by the new command. For example to
reprogram the ENTER key to transmit “Hi!”, type ENT48 69 21.

Note that:

• Each line is terminated with a carried return (0x0D or CONTROL-M).

• Nothing is displayed if the command is accepted, only if there is an error. Type LST to see what has been done.

• Entries are not case-sensitive.

• All values are 2 digit hexadecimal values.

• Each command string may be 0 (indicating that nothing will be sent) to 10 bytes long.

• Backspaces are not supported. If an error is made, press the ENTER key and retype the line.

• Values may be separated by spaces, commas or tabs as all are ignored.
When all the necessary changes have been made, they can be reviewed by typing LST. To save and exit programming,

type SAV. To abandon the changes that you have made, simple reset the keyboard.

The two labels SLO and FST represent the time between repeated command transmissions of the 4 joystick operations.
The SLO interval is the slow repeat rate when the joystick is deflected a little, and the FST is the fast repeat rate when
the joystick is fully deflected. These values are in units of 5mS, so the default slow value of 64 hex is 100 decimal *
5mS = 500mS.

Changing VCR command parity is specified by PAR DPS where D=Data Bits (7 or 8), P=Parity (N, O or E) and S=Stop
Bits (1 or 2), e.g., PAR 8N1 or PAR 7E2. Note that when configuring the VCR, it always uses 8 data bits, no parity and
1 stop bit, and the baud rate selected from the Special Config menu.

38

Keyboard Installation and Operation

Appendix B: Monitor Arming Commands

Monitors are armed for alarm call up with codes that specify the following three parameters:

1. The

2. The

3. The
To arm a monitor with an ADCC0300 keyboard:

1. Call the monitor to be armed.

2. Enter the monitor arming code number (see table).

3. Press the FUNCTION ( ) key, press the F1 ( ) key.
A keyboard operator can also program any monitor armed for instant or auto clearance, for clearance via manual

override. Manual override is enabled or disabled after the arming code is programmed. If enabled, an "A" will appear
after the three-letter acronym for the arming code that appears on the monitor status line.

When using the AD1024 matrix switcher/controller system, monitors can be armed through S3 system setup software
with a PC interface, or through the AD1024 embedded software with an ADCC0300 keyboard. Following is a table of
monitor arming codes and the commands that enable the codes.

display

method (

queuing

method (

clearance

Monitor Arming Code Monitor Acronym Command Sequence

Display Arming Status see entries below 300, FUNCTION, F1
Single, Sequence, Instant SSI 301, FUNCTION, F1
Single, Sequence, Auto SSA 302, FUNCTION, F1
Single, Sequence, Manual SSM 303, FUNCTION, F1
Single, Hold, Instant SHI 304, FUNCTION, F1
Single, Hold, Auto SHA 305, FUNCTION, F1
Single, Hold, Manual SHM 306, FUNCTION, F1
Block, Sequence, Instant BSI 307, FUNCTION, F1
Block, Sequence, Auto BSA 308, FUNCTION, F1
Block, Sequence, Manual BSM 309, FUNCTION, F1
Block, Hold, Instant BHI 310, FUNCTION, F1
Block, Hold, Auto BHA 311, FUNCTION, F1
Block, Hold, Manual BHM 312, FUNCTION, F1
Dual, Hold, Instant DHI/DSI* 313, FUNCTION, F1

Dual, Sequence, Instant
Dual, Hold, Auto DHA/DSA* 314, FUNCTION, F1

Dual, Sequence, Auto
Dual, Hold, Manual DHM/DSM* 315, FUNCTION, F1

Dual, Sequence, Manual
Disarm Monitor 316, FUNCTION, F1
Enable Monitor Override 317, FUNCTION, F1
Disable Monitor Override 318, FUNCTION, F1

single, dual

method (

sequence

instant, auto

, or

or

block

hold

, or

monitors).

).

manual

).

* In dual display applications, the first three-letter acronym is displayed on the

acronym is displayed on the

sequence

monitor.

39

hold

monitor. The second three-letter

ADCC0200 and ADCC0300

Appendix C: Troubleshooting

Problem

✗ No power to keyboard

✗ No response to keystrokes (power

verified)

✗ Keyboard responds to keystrokes on

some, but not all keys

✗ Cannot perform menu programming

(ADCC0300 only)

✗ Display not visible

✗ Keyboard speaker not audible

Check List

✓ Check AC outlet
✓ Check wall transformer connections
✓ Check cable connections to keyboard and

keyboard matrix interface

✓ Measure transformer output at keyboard matrix

interface

✓ Check connection of keyboard matrix interface to

system controller's communication port

✓ Check baud rates for keyboard and system

controller

✓ Verify VCR/Monitor status

✓ Verify if Program Lock mode is on. Program Lock

mode passcode is required to perform program­ming functions.

✓ Verify display brightness and contrast level

✓ Verify speaker enabled in keyboard menu

✗ Cannot access main menus of CPU

(ADCC0300 only)

✓ Verify that keyboard is in program mode
✓ Verify that correct monitor is selected for menu

programming

✓ Verify CPU program monitor output is connected

40

Appendix D: Specifications

Keyboard Installation and Operation

Model Numbers

ADCC0200 .................. Keyboard with two-axis joystick

ADCC0300 .................. Keyboard with three-axis joystick

MP-CBL....................... Spare cable

MP-KMI ....................... Keyboard Matrix Interface

ADCCACPSN ............. US Remote Keyboard Kit

ADCCACPSP .............. EU/UK Remote Keyboard Kit

LCD

Size ............................. 16 x 2 white text on black background,

user adjustable

Controls

Keys ............................ 47 Tactile, color coded, rubberized keys

Joystick ....................... ADCC0200 - Two axis joystick for pan

and tilt control
ADCC0300 - Three axis joystick for
pan, tilt and zoom control and menu
navigation

Connectors

RS232, power ............. 2 x RJ45 to switcher/controller via

terminal block

Electrical

Supply voltage .............9 to 15V DC

Maximum current ......... 500mA

Mechanical

Dimensions .................13.4" x 5.2" x 3.2" (34.0 x 13.2 x 8.0 cm)

Weight (max.) .............. 3.3lb (1.5 kg)

Shipping weight ........... 4.2 lb (1.9 kg)

Construction ................ Mild steel/aluminum with ABS end caps

Color ........................... Black

Environmental

Operating temperature 0O to 30O C, 32O to 86O F

O

Storage temperature .... 0

Operating humidity ...... 90% max, relative humidity, non-

to 40O C, 32O to 104O F

condensing

Regulatory

Emissions ....................FCC Part 15, Subpart B Class A

Immunity ...................... CE: EN50130-4

CE: EN50081-1

41

ADCC0200 and ADCC0300

Index

A

Alarms 24
Auto Focus 20
Auto Iris 19
Auto Repeat Mode 35
Auxiliaries 24

B

Baud Rate 34
Biasing the Network 14

C

Calling a Camera to View on a Monitor 17
Calling Presets (Shots) 20
Calling Salvos 23
Calling Views 24
Camera Flip 19
Camera Focus 19
Camera Iris 19
Clearing Patterns 32
Connecting Keyboards

Multiple Keyboards 14, 15
Single Keyboard with Cable Length Over Seven Feet 12
Single Keyboard with Cable Length Under Seven Feet 13

Connection and Setup 11

D

Defining Patterns 31
DirectSet 21
Disabling Telemetry 27
Disabling/Enabling Keyboard Sounder 35
Dome Camera DirectSet 21
Dome Menu Functions 30

E

Enabling Telemetry 27
Entering Matrix Menu Mode 29
Exiting Program Mode 28

F

F1 Commands 27
F2 Commands 32
Factory Defaults 35

42

Function Tables

DirectSet Feature 10
Dome Operations 9
Matrix Menu Operations 8
Standard Matrix Operations 7
VCP (PIP) / Direct Control Mode 10

H

Holding Tours 22

K

Keyboard

Address 33
Audible Warning 25
Display 17
Display Contrast 25
Retries 33

Sounder 35
Keyboard Matrix Interface 11
Keys 4

L

LCD 17
Locking and Unlocking a Camera 26
Logging Off 16
Logging On 16

Keyboard Installation and Operation

M

Make/Break Keypress Mode 35
Matrix Menu 29

N

Navigating Dome Camera Menus 30
Network Timeout Period 34

O

Operating a VCR 26

P

Pan, Tilt and Zoom 18
Passcodes 16
Patterns

Clearing 32

Defining 31

Running 21
Presets

Calling 20

Setting 31

43

ADCC0200 and ADCC0300

Program Mode

Entering 28
Exiting 28
Locking 28
Setting the Passcode 36

Programming Dome Patterns 31

R

Resetting to Factory Defaults 35
Restarting a Held Tour 22
Reversing Tours 23
RS485 and RS232 Modes 35
Running Patterns 21
Running Tours 22

S

Salvos 23
Selecting Monitors 17
Setting Presets 31
Setting the Baud Rate 34
Stepping Through Tours 22
Stopping Tours 23

T

Telemetry Enable/Disable 27
Terminating the Network 14
Tours

Holding 22
Restarting 22
Reversing 23
Running 22
Stepping Through 22
Stopping 23

U

User Names 16

V

Viewing Satellite Sites 25
Views

Calling 24

44

Keyboard Installation and Operation

45

ADCC0200 and ADCC0300

46

Keyboard Installation and Operation

47

ADCC0200 and ADCC0300

8200-0855-05 A0

Please visit our website for more information

www.americandynamics.net

© 2006 American Dynamics
Product specifications subject to change without notice
Certain product names mentioned herein may be trade names
and/or registered trademarks of other companies

48

MP200-300HB-7