American DJ Volcano User Manual
American DJ
®
User Instructions
Affordable Quality Lighting Products from American DJ® Los Angeles, CA. 90058 USA
c
VOLCANO
SPECIFICA TIONS:
MODEL - Volcano™
WEIGHT: 19 LBS.
DIMENSIONS: 7" X 8" X 21"
FUSE: 7A AGC
SUPPLY VOLTAGE: 120V
WARM UP TIME: 4 Minutes
TANK CAPACITY: 1 Quart Internal
OUTPUT: 2,500 cubic feet per minute
FLUID TYPE: Water Base American DJ Fog Juice™
DUTY CYCLE: None
HEATER: 750 WATT
NEVER POINT OR AIM ANY FOG MACHINE TOWARDS PEOPLE OR
THEIR CLOTHING. FOG MACHINES EMIT HOT VAPOR AND
SHOULD BE USED WITH THE SAME CARE THAT YOU WOULD
OBSERVE WHEN USING AN ELECTRIC KETTLE OR IRON.
TO HELP PREVENT THE UNIT FROM CLOGGING, USE
AMERICAN DJ® CLEAN MACHINE™ LIQUID. CLEAN MACHINE IS
RECOMMENDED WHEN STORING YOUR FOGGER FOR MORE
THAN 1 WEEK OR AT LEAST ONCE A MONTH AS NORMAL
MAINTENANCE WHEN UNIT IS BEING USED ALL THE TIME. ITS
LIKE A TUNE UP FOR YOUR FOG MACHINE! CLEAN MACHINE
REMOVES PARTICLE BUILD UP IN THE HEATER AND GIVES
LONGER LIFE TO THE FOG MACHINE. CLEAN MACHINE IS
AVAILABLE IN GALLON OR QUART BOTTLES FROM YOUR
LOCAL AMERICAN DJ® DEALER.
TM
Electronic Thermo Sensing (E.T.S.)
with ETS
TM
Introduction:
Congratulations on your purchase of the American DJ® Volcano.™ The American DJ® Volcano™ is
a unique innovation into the fog machine industry. This unit acts as a fog/haze machine combination to give you a constant even flow at almost any given time. This is made possible due to an on
board micro processor which constantly monitors the operating temperature of the machine. We call
this feature Electronic Thermo Sensing (E.T.S.). You also will not have to worry about running the
Volcano™ dry of fog fluid due to a new feature that we have added called “The Low Fluid Indicator.”
A sensor in the fluid reservoir senses when the fluid level goes down too low and shuts the unit down
before any damage can occur.
Operating Instructions:
Before attempting any operation, please make sure there is an adequate supply of American DJ Fog
Juice™ in the machines fluid reservoir. Because the volcano allows for continuous fog output, keep
Caution: Save yourself a headache, please read and follow all the instruction
before attempting any operation! This unique unit has many new added feature to
fog machine technology that you may not be familiar with.
the reservoir full. Plug the Volcano™ into a standard 120V electrical outlet. The unit will draw up to
6A of power. Connect the remote control into the rear of the machine. Turn the power switch to the
“ON” position. After turning the unit on, the red L.E.D. on the remote will glow indicating that the
unit is receiving power. After the machine initial warm up period, of approximately four (4) minutes,
the green L.E.D. on the remote will glow indicating that the machine is now ready for use. The first
time the machine is used it will take 5-30 seconds to prime (fill the pump with fluid).
The pump may
also need to be primed if the machine has not been used or has been stored for an extended period of
time.
If fog does not emit after 30 seconds, check the fluid in the tank , also check the hose to making
sure there is fluid going through the hose.
Manual Operation:
For manual operation, push the green button on the remote control. Holding the green button down
will give you 100% output for as long as you hold the button down. For advanced timer control operation, please see the next section: Timer Operation.
Timer Operation:
The timer remote allows automatic control of fog output. To begin timer operation, press the yellow
button on the remote, this should make the yellow L.E.D. glow. Next, adjust the
““IInntteerrvvaall””
and
““VVoolluummee””
knobs to your desired settings. The interval time is the amount of time it will take for the
fogger to trigger output between the output blast. The intervals can range from 0 seconds to 5 minutes and is adjusted by turning the interval knob in a clockwise direction. Setting the interval to 0
will shut off the timer function and only allow manual output operation. Setting the interval to a full
clockwise position will trigger output approximately every 5 minutes. The volume adjustment allows
you to increase or decrease the amount of fog discharged with every blast. The volume can range
from 0% (full counter-clockwise position) to 100% (full clockwise position). 0% will give you no output and 100% will give you the maximum possible output (approximately 2,500 cu.ft. per a minute).
You may also set the Volcano™ for continuous fog output. Continuous fog output is a new innovation
to world of fog machines and will give you a consistent, even stream of fog throughout it’s cycle. For
continuous fog output press the red button on the remote control. After pressing the red button fog
should begin to emit from the machine, at this time adjust the “VOLUME” until you reach your
desired fog output level.
Electronic Thermo Sensing / E.T.S.:
This feature allows you to have fog output available at almost any time. A small on board micro
processor constantly monitors the operating temperature of the Volcano™ machine. When the
Volcano™ machine drops one (1) degree in temperature, the E.T.S. automatically senses this change
and turns the heater on to raise the temperature to that one degree lost. This enables the end user to
have fog output at anytime. The only time fog will not be available, is at the end of the machines duty
cycle (The fog output was maxed out and the heater has to reheat completely). The reheat process
can take from one (1) to two (2) minutes.
Affordable Quality Lighting Products from American DJ® Los Angeles, CA. 90058 USA
Loading...