American DJ V-01 Plus User Instructions
Professional Power Ampliers
AMERICAN AUDIO®
6122 S. Eastern Ave.
Los Angeles Ca. 90040
Rev. 2/08
V-01 Plus Series
User Instructions
This symbol is intended to alert the user to the presence of non insulated "dangerous voltage" within the product's enclosure that may be of sufcient magnitude to
constitute a risk of electric shock to persons.
This symbol is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
CAUTION: Risk of the electrical shock - DO NOT OPEN!
CAUTION: To reduce the risk of electrical shock, do not remove cover. No user serviceable parts inside. Refer all servicing to qualied service personnel.
WARNING: To prevent electrical shock or re hazard, do not expose this amplier to rain or moisture. Before using this amplier, read the user manual for further warnings.
Este símbolo tiene el propósito de alertar al usuario de la presencia de “voltaje peligroso“ que no tiene aislamiento dentro de la caja del producto que puede tener
una magnitud suciente como para constituir riesgo de corrientazo.
Este símbolo tiene el propósito de alertar al usuario de la presencia de instrucciones importantes sobre la operación y mantenimiento en la literatura que vienc con
el producto.
PRECAUCIÓN: Riesgo del choque eléctrico - NO SE ABRA
PRECAUCIÓN: Para disminuir el riesgo de choque eléctrico, no quite la cubierta. No hay piezas adentro que el usario puede reparar. Deje todo mantenimiento al los téc-
nicos cualicados.
ADVERTENCIA: Para prevenir choque eléctrico o riesgo de incendios, no deja expuesto a la lluvia o a la humedad este amplicador. Antes de usar este amplicador, lea
mas advertencias en la guia de operacion.
Ce symbole est utilisé pur indiquer à l’utilisateur la présence à l'intérieur de ce produit de tension non-isolée dangereuse pouvant être d'intensité sufsante pour
constituer un risque de choc électrique.
Ce symbole est utilisé pour indiquer à l’utilisateur qu'il trouvera d'importantes instructions importantes sur l'utilisation et l'entretien de l'appareil dans la littérature
accompagnant le produit.
ATTENTION: Risque de choc électrique - NE PAS OUVRIR!
ATTENTION: An de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à l’intérieur aucune piéce pouvant être réparée par l'utilisateur. Coner
l'entretien à un personnel qualié.
AVERTISSEMENT: An de prévenir les risque de décharge ou de feu, n’exposez pas cet appareil à la pluie ou à l’humidité. Avant d’utiliser cet amplicateur, lisez les aver-
tissements supplémentaries situés dans le guide.
Dieses Symobl soll den Anwender vor unisollierten gefährlichen Spannungen innerhalb des Gehäuses warnen, die von Ausreichender Stärke sind, um einen elek-
trischen Schlag verursachen zu können.
Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betref-
fen.
VORSICHT: Risiko - Elektrischer Schlag! Nicht öffnen!
VORSICHT: Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es benden sich keine Teile darin, die vom Anwender repariert
werden könnten. Reparaturen nur von qualizierte Fachpersonal durchführen lassen.
ACHTUNG: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte diesen Gerät nicht dem Regen oder Feuchtigkeit ausgesetz werden. Vor Inbetriebnahme
unbedingt die Bedienungsanleitung lesen.
©American Audio® - www.americanaudio.com - V-01 Series™ Power Amplifier User Manual Page 2
CAUTION
Do not open -
risk of electric shock
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
THERE ARE NO USER SERVICEABLE PARTS
INSIDE. REFER ALL SERVICE TO YOUR
AUTHORIZED AMERICAN AUDIO® DEALER.
The lightning flash with an arrow triangular
symbol is intended to alert the user to the
presence of non insulated “dangerous voltage” within the products enclosure, and
may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point triangular symbol is
intended to alert the user to the presence
of important operating and maintenance
(servicing) instructions in the user manual
accompanying the amplifier.
FOR OPTIMUM PERFORMANCE AND
RELIABILITY DO NOT PRESENT THE
AMPLIFIER WITH A SPEAKER LOAD
OF LESS THAN 2 OHMS OR ANY
COMBINATION OF SPEAKERS THAT
TOGETHER ARE LESS THAN 2 OHMS!
USING ONE SPEAKER, IT MUST BE
RATED AT 4 OR MORE OHMS.
USING TWO SPEAKERS, THEY MUST
RATED EACH AT 4 OR MORE OHMS.
USI NG THR EE SPE AK ERS , T HEY
MUST BE RATED EACH AT 8 OR MORE
OHMS.
P O U R A S S U R E R L A F I A B I L E T E E T
OBTENIT UNE PERFORMANCE OPTIMALE,
NESOUMET TE JAM A IS L’AMPLIFICATEUR
A U NE C HARG E D’I MPEDANCE TOTAL E
INFERIEURE A 2 OHMS, NI AVEC UN H.P. NI
EN COMBINAISON DES H.P.
AV EC UN H . P., I L FAUT UNE CHA RGE
D’IMPEDANCE MINIMUM DE 2 OHMS.
AVEC DEUX H.P., FAUT POUR CHAOUN UNE
CHARGE D’IMPEDANCE MIN I MUM D E 4
OHMS.
AVEC TROIS H.P., FAUT POUR CHAOUN UNE
CHURGE D’IMPEDANCE M I NIMUM D E 8
OHMS.
CONTENTS:
Safety Precautions.......................................................................................................................................................................................4
Introduction...............................................................................................................................................................................................4
Front Panel...................................................................................................................................................................................................5
Rear Panels..................................................................................................................................................................................................6
Inputs...........................................................................................................................................................................................................11
Outputs............................................................................................................................................................................................................11
Speakon Output Connector Assembly.......................................................................................................................................................13
Operating Modes........................................................................................................................................................................................14
Protection Circuitry
Limiter.................................................................................................................................................................................................15
Short Circuit Protection...................................................................................................................................................................15
Thermal Protection..........................................................................................................................................................................16
Amplier Features.......................................................................................................................................................................................16
Subwoofer and Speaker Setup..............................................................................................................................................................17-18
Warranty.................................................................................................................................................................................................19
Specications...............................................................................................................................................................................................20
©American Audio® - www.americanaudio.com - V-01 Series™ Power Amplifier User Manual Page 3
Important Precautions
Introduction
• To reduce the risk of electrical shock or re, do not expose this
unit rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of elec-
trical shock and re in case of an internal short.
• Disconnect main power before making any type of connection
• Do not remove the cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack.
• Always be sure to mount this unit in an area that will allow
proper ventilation. Allow about 6” (15cm) between this device
and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main
power.
• Always mount this unit in a safe and stable manner.
• Power cords should be routed so they are not likely to be
walked on, pinched by items placed upon or against them.
• Cleaning -The outside of the unit should be wipe down with a
soft cloth and mild cleaner when needed.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel
when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen on, or liquid has been spilled into the unit.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
©American Audio® - www.americanaudio.com - V-01 Series™ Power Amplifier User Manual Page 4
Introduction: Congratulations and thank you for purchasing
the American Audio® V-01 Series™ amplifier. This amplifier is a
representation of American Audio’s continuing commitment to
produce the best and highest quality products all at an affordable
price. Please read and understand this manual completely before
attempting to operate your new amplifier. This booklet contains
important information concerning the proper and safe operation of
your new amplifier.
Unpacking: Every V-01 Series™ amplier has been thoroughly
tested and has been shipped in perfect operating condition.
Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged,
carefully inspect your unit for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the event
damage has been found or parts are missing, please contact our
toll free customer support number for further instructions. Please
do not return the amplier to your dealer without contacting customer support rst.
Installation: This amplifier is designed to mount into a standard
19” rack. The front panel provides four holes used to screw the
unit into a rack. The unit also provides a way to rear mount the
unit into a rack for added security. Rear mounting the unit is especially recommended for this amplifier if the unit is to mounted into
a mobile rack.
Customer Support: American Audio® provides a toll free custom-
er support line, to provide set up help and to answer any question
should you encounter problems during your set up or initial opera-
tion. You may also visit us on the web at www.americanaudio.com
for any comments or suggestions. For service related issue please
contact American Audio®. Service Hours are Monday through
Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice: (800) 322-6337 E-mail: support@americanaudio.com
Fax: (323) 582-2610
POWE R
ON
OFF
PROFESSIONAL POWER AMPLIFIER
STEREO
-20dB
SIGNAL
-10dB
CLIP
PROTEC T
0
10
0
10
Front Panel Control
All ampliers in the
series.
1
876432 5
Figure 1
10
9
1. Power Switch - This switch is used to control the units main power.
2. Channel 1 Gain Control - This rotary knob is used to control the output signal of channel one. Turning the knob in a clockwise direction will in-
crease signal output.
3. Channel 1 Clip Indicator - This red LED will begin to ash when channel one begins to overload (clip). At this point channel one will begin to
distort. Under heavy clipping activity lower the channel one gain control to reduce the risk of damage to your speakers and amplier. This LED may
glow when the unit has been turned off, this is normal.
4. Channel 1 Protect Indicator - The red Protect LED will begin to glow when the channel goes into protect mode. When the channel goes into
protect mode all output for that channel will turn off. This is to protect any speakers connected to the channel.
5. Function Indicators - This indicator details the operating mode of the amplier. This LED also functions as a power indicator.
6. Channel 2 Protect Indicator - The red Protect LED will begin to glow when the channel goes into protect mode. When the channel goes into
protect mode all output for that channel will turn off. This is to protect any speakers connected to the channel.
7. Channel 2 Clip Indicator - This red LED will begin to ash when channel one begins to overload (clip). At this point channel one will begin to
distort. Under heavy clipping activity lower the channel one gain control to reduce the risk of damage to your speakers and amplier. This LED may
glow when the unit has been turned off, this is normal.
8. Channel 2 Gain Control - This rotary knob is used to control the output signal of channel two. Turning the knob in a clockwise direction will increase signal output.
9. Channel 2 Signal Indicators - These green and yellow LED’s will glow according to the average signal output.
10. Channel 1 Signal Indicators - These green and yellow LED’s will glow according to the average signal output.
Note: When using the V-6001 at maximum power you must use 12 gauge speaker cables.
©American Audio® - www.americanaudio.com - V-01 Series™ Power Amplifier User Manual Page 5
V6001 & V5001
13 1320191817161514 232221
Rear Panel
Figure 2
33 32343536 30
Note: When using the V-6001 at maximum power you must use 12 gauge speaker cable.
13. Cooling Fans - Dual variable speed cooling fans
14. Channel 1 XLR THRU Jack - This jack is used to send a parallel signal from the channel one input jacks to another device or amplifier.
15. Channel 1 XLR input - Channel one balanced input jack. This combo jack will accept a standard 1/4 plug or XLR 3-pin balanced male
plug.
29 28 27 26 25 2431
16. Channel 1 Limiter Switch - This is used to activate the channels built-in limiter. The limiter reduces the average input level when the signal
begins to distort, this process is designed to reduce distortion and protect the speakers. See limiter page 15.
17. Channel 1 HPF (High Pass Filter) Switch - When this function is activated it removes all frequencies below 40Hz. Therefore the reproduction
of the signal’s bass portion is optimized, since all ultra-low frequencies are eliminated.
18. Channel 1 Frequency Adjustment - This knob is used to adjust the frequency level sent to your speaker on channel one when running the
channel in subwoofer mode.
19. Channel 1 Subwoofer Mode On/Off Switch - Turns the subwoofer mode for channel one on and off.
20. Channel 1 Rear Gain Control - This rotary knob is used to control the output signal of channel one. Turning the knob in a clockwise direction
will increase signal output. You must have the VOLUME CONTROL SWITCH in the “Rear” position to use this gain control.
21. Channel 1 Output Jack/5 way Binding Post - Connect to your speaker’s input jack. Red is positive signal and Black is negative signal.
22. Channel 1 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your
speaker’s Speakon input jack. In Mono Bridge mode, use pins 1+ and 2+ of this 4-pole Speakon connector.
23. Reset Button - This button is used to reset the breaker.
24. AC Cord - Plug this cable into a standard 110~120v wall outlet. Check that the voltage in your area matches the ampliers required voltage.
©American Audio® - www.americanaudio.com - V-01 Series™ Power Amplifier User Manual Page 6
25. Channel 2 Speakon Output - Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your
speaker’s Speakon input jack.
26. Ground Switch - If hear a hum or any interference, put the Ground switch in the “On” postion .
27. Channel 2 Output Jack/5 way Binding Post - Connect to your speaker’s input jack. Red is positive signal and Black is negative signal.
28. Mode Switch - This switch controls the amplier’s operating mode. The amplier can operate in three different modes; Mono Bridge, Parallel
Mono, or Stereo. The amplier is shipped in stereo mode.
29. Channel 2 Limiter Switch - This is used to activate the channels built-in limiter. The limiter reduces the average input level when the signal
begins to distort, this process is designed to reduce distortion and protect the speakers. See limiter page 15.
30. Channel 2 Rear Gain Control - This rotary knob is used to control the output signal of channel two. Turning the knob in a clockwise direction
will increase signal output. You must have the VOLUME CONTROL SWITCH in the “Rear” position to use this gain control.
31. Channel 2 Subwoofer Mode On/Off Switch - Turns the subwoofer mode for channel two on and off.
32. Channel 2 Frequency Adjustment - This knob is used to adjust the frequency level sent to your speaker on channel two when running the
channel in subwoofer mode.
33. Channel 2 HPF (High Pass Filter) Switch - When this function is activated it removes all frequencies below 40Hz. Therefore the reproduction
of the signal’s bass portion is optimized, since all ultra-low frequencies are eliminated.
34. Volume Control Switch “Contractor Smart” - This switchs control of the amplier’s volume control. The amplier’s volume can be either con-
trolled from the rear of the unit or the front. If the switch is in the “Rear” position, the volume control located in the rear is used to control the volume.
In this same postion the volume controls in the front of the unit will be disabled and cannot be used to adjust the volume.
35. Channel 2 XLR THRU Jack - This jack is used to send a parallel signal from the channel two input jacks to another device or amplifier.
36. Channel 2 XLR Input - Channel two balanced input jack. This combo jack will accept a standard 1/4 plug or XLR 3-pin balanced male
plug.
Note: When using the V-6001 at maximum power you must use 12 gauge speaker cable.
©American Audio® - www.americanaudio.com - V-01 Series™ Power Amplifier User Manual Page 7
Loading...