UV 72IP
User Instructions
©2017 ADJ Products, LLC all rights reserved. Information, specications,
diagrams, images, and instructions herein are subject to change without
notice. ADJ Products, LLC logo and identifying product names and numbers
herein are trademarks of ADJ Products, LLC. Copyright protection claimed
includes all forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted. Product
names used in this document may be trademarks or registered trademarks
of their respective companies and are hereby acknowledged. All non-ADJ
Products, LLC brands and product names are trademarks or registered
trademarks of their respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries
to any persons, and direct or indirect economic loss associated with the use
or reliance of any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation of this product.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This device uses and can radiate radio frequency energy and, if not
installed and used in accordance with the included instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to radio or television recep-
tion, which can be determined by turning the device o and on, the user is encouraged to try to
correct the interference by one or more of the following methods:
· Reorient or relocate the device and/or antenna.
· Increase the separation between the device and the receiver.
· Connect the device into an electrical outlet on a circuit dierent from that which the radio
receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn
o all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in
use. Thank you!
DOCUMENT VERSION
Please check www.adj.com for the latest revision/update of this guide.
Date
Document
Version
Software
Version
>
DMX
Channel
Mode
Notes
7/17
07/13/17
1
1.00
1/2/3 Initial Release
UV 72IP Introduction
UV 72IP Features
Unpacking: Thank you for purchasing the UV 72IP by ADJ Products,
LLC. Every UV 72IP has been thoroughly tested and has been shipped
in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect your xture for any damage and be
sure all accessories necessary to operate the unit has arrived intact. In
the case damage has been found or parts are missing, please contact
our toll free customer support number for further instructions. Do not
return this unit to your dealer without rst contacting customer support.
Introduction: The UV 72IP is an IP65 outdoor rated, DMX intelligent,
UV LED par fixture with ADJ’s WiFly TransCeiver with wireless DMX
built-in. This xture can be used in a stand alone mode or connected
in a Master/Slave conguration. This wash has three operating modes:
Auto Fade mode, UV Dimmer mode, and DMX control mode.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@AmericanDJ.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
• Electronic Dimming 0-100%
• DMX-512 protocol
• 3-Pin DMX Connections
• 3 DMX Channel Modes
• Built-In ADJ’s WiFly EXR Wireless DMX Up to 2,500 feet/760M
• IP 65 Rated Power Connection locking system
• UC IR Compatible & Airstream IR Comptiable
• Multiple Unit Power Linking (See page 18)
Incuded Accessories:
1 x powerCON TRUE1 power cable
1 x Dual Yoke/Stand
1 x UC IR Remote Control + 1 x Airstream IR Transmitter
UV 72IP Warranty Registration
The UV 72IP carries a 2 year (730 Days) limited warranty. Please fill
out the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
UV 72IP Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-
ping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 2
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 3
UV 72IP Safety Precautions
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 19 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
CAUTION: This unit like any wireless device is highly susceptible
to static electricity. Static electricity can severly damage the unit.
UV 72IP Safety Precautions
RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!
FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT
AT A WAVELENGTH OF 390NM - 410NM.
WEAR PROPER EYE AND SKIN PROTECTION.
AVOID PROLONGED PERIODS OF EXPOSURE.
AVOID WEARING WHITE COLOR CLOTHING AND/OR
USING (UV) PAINTS ON SKIN.
AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES
SHORTER THAN 11 feet (3.3m).
DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL
COVER PROTECTIVE LENS.
DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV)
LIGHT DIRECTLY WITH OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.
INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE DISCOMFORT IF EXPOSED TO THE
ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 4
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 5
IP65 RATED
An IP rated lighting fixture is one, which is commonly installed in outdoor
environments and has been designed with an enclosure that effectively
protects the ingress (entry) of external foreign objects such as dust and water.
The International Protection (IP) rating system is commonly expressed as "IP"
(Ingress Protection) followed by two numbers (i.e. IP65) where the numbers
define the degree of protection. The first digit (Foreign Bodies Protection)
indicates the extent of protection against particles entering the fixture and
the second digit (Water Protection) indicates the extent of protection against
water entering the fixture. An IP65 rated lighting fixture is one, which has been
designed and tested to protect against the ingress of dust (6) and highpressure water jets from any direction (5).
MARINE/COASTAL ENVIRONMENT INSTALLATIONS!
Please note although this fixture is IP rated, the fixture is NOT suitable for
marine and/or coastal environment installations. Installing this fixture in a
marine and/or coastal environment may cause corrosion and/or excessive
wear to the interior and/or exterior components of the fixture. Damages
and/or performance issues resulting from installation in a marine and/or
coastal environment will void the manufactures warranty and will NOT be
subject to any warranty claims and/or repairs.
Ensure ALL connections and end caps are properly sealed with a non-
conductive dielectric grease (available at most electrical suppliers) to
prevent water ingress/condensation and/or corrosion.
UV 72IP Protective Valve UV 72IP IP Notice
OPTIONAL CORROSION- RESISTANT COATING
Optional Corrosion-Resistant Coatings may be available for this fixture.
Please consult your ADJ Products, LLC sales representative for details.
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 6
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 7
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
UV 72IP Set Up
UV 72IP Set Up
Power Supply: The ADJ UV 72IP contains an automatic voltage
switch, which will auto sense the voltage when it is plugged into the
power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
DMX Cable Requirements: The UV 72IP can be controlled via DMX-
512 protocol. The UV 72IP has 3 DMX channel modes, please see pages
9-10 for the dierent modes. The DMX address is set on the back panel
of the UV 72IP.
Cable Requirements: This xture powered by powerCON TRUE1 power
cables. These cables are specically designed to maintain the integrity
of the IP rating. When using this xture outdoors be sure to ONLY use
the ADJ cables that have been manufactured to meet the IP rating.
“First” DMX Cables - Special DMX “First” cable may be purchased
from ADJ to provide a means of data communication with standard DMX
xtures for indoor use. These cables will come with the IP rated connector on one end and either a 3-pin XLR male or female connector on the
other depending on model. Be sure to only use these cables for intergrading this xture in a standard DMX chain.
“First” Power Cable – A special power “First” cable is included with
every xture. This cable is used to provide power to your xture. This
cable comes with the IP rated twist lock connector on one end and a
standard Edison 3-prong, grounded prong on the other end. Be sure to
only use this cable for power distribution and never attempt to connect
this cable to the DMX lines.
You can chain multiple xtures together through serial linking. Using the
IP rated signal cables provided through ADJ (part# TRU113). Always
be sure to daisy-chain your in and out data connections, never split
or “Y” your DMX connections unless you are using an approved DMX
splitter such as the ADJ WiFly D6 Branch or the original D6 Branch
(Both not IP rated).
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
5-Pin XLR DMX Connectors.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 8
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 9
UV 72IP 1 Channel Mode
Channel Value Function
UV 72IP 3 Channel Mode
Channel Value Function
1 UV DIMMER
0 - 255 0% - 100%
UV 72IP 2 Channel Mode
Channel Value Function
1 UV DIMMER
0 - 255 0% - 100%
2 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
1 UV DIMMER
0 - 255 0% - 100%
2 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
3 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATER
101 - 255 DEFAULT TO UNIT CURVE SETTING
UV 72IP Dimensional Drawing
11.50”/292mm
8.2”/208.5mm
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 10
8.46”/215mm
9.17”/233mm
3”/77.5mm
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 11
UV 72IP Operating Instructions
UV 72IP Operating Instructions
LED Display On/Off:
To set the LED display to turn off 60 seconds, press the MODE button
until “don” is displayed, press the UP button to display “doff”. Now the
display will disappear after 60s. Press any button to turn the display on
again. Be advised though that the display will turn off automatically after
10 seconds.
To set the display press the MODE button until “dXX” is displayed. Use
the UP or DOWN buttons to select either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 60 seconds.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The UV
72IP has 3 DMX modes. See pages 9-10 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
“d.XXX” is displayed. “XXX” represents the current displayed ad dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button so that “Ch.XX” is displayed.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 1 Channel Mode, press the UP or DOWN buttons until
“Ch01” is displayed. This is the 1 Channel DMX Mode.
• To run the 2 Channel Mode, press the UP or DOWN buttons until
“Ch02” is displayed. This is the 2 Channel DMX Mode.
• To run the 3 Channel Mode, press the UP or DOWN buttons until
“Ch03” is displayed. This is the 3 Channel DMX Mode.
4. Please see pages 9-10 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control ler.
Slave Setting:
1. Plug the fixture in and press the MODE button until “SLAv” is
displayed. The unit now designate a “Slave” unit in a Master-Slave
set up.
UV Dimmer Mode:
1. Plug the fixture in and press the MODE button until “u: XXX” is
displayed. You are now in UV dimming mode. Press the UP and
DOWN buttons to adjust intensity.
2. After you have adjusted the output intensity you can then activate
strobing by pressing the SET UP button to enter the strobe mode.
3. “FS: XX” will be displayed, this is strobe mode. The strobe
can be adjusted between “00” (flash off) to “15” (fastest flash).
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See
page 17 for the different dimming curves.
1. Plug the fixture in and press the MODE button until the current
DMX address is displayed.
2. Press the SET UP button until “dr-X” is displayed. “X” represents
the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your
desired dimming curve.
Auto Fade Mode:
1. Plug the fixture in and press the MODE button until “Fd.XX” is
displayed. This is Auto Fade mode.
2. Use the UP and DOWN buttons to adjust the fade speed. “1”
being the slowest fade speed, and “16” being the fastest.
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 13ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 12
UV 72IP Operating Instructions
UV 72IP Master-Slave Configuration
ADJ Remote Activation:
This function is used to activate and deactivate the IR sensor. When
this function is activated you can control the fixture using either the
ADJ UC IR or Airstream App. Please see page 16 for the controls and
functions.
1. Plug the fixture in and press the MODE button until “dXX” is dis played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “IrXX” is displayed. “XX” represents
either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func tion (On) or deactivate it (Off).
WiFly On/Off and Wireless Addressing:
This function is used to activate the WiFly control and set the WiFly
address.
NOTE: The address must match the address that is set to WiFly
TransCeiver or WiFly controller.
1. Plug the fixture in and press the MODE button until “rCXX” is
displayed. You are in wireless set up mode.
2. Press the UP or DOWN buttons the UP or DOWN buttons to turn
the Wireless “On” or “Off”.
3. Press the SET UP button to enter the Wireless address menu. Use
the UP or DOWN buttons to select your desired Wireless address.
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con nector is the ouput. The first unit in the chain (master) will use the
female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” units press the MODE button until “SLAv” is
displayed. The unit is now set as the “Slave” unit. Each slave unit
must be set to the same setting.
4. Connect the rst “Slave” unit to the “Master”, and the “Slave” unit
should now start to fall in line and follow the “Master”.
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings and a Auto program will run.
1. Plug the fixture in and press the MODE button until “dXX” is dis played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “dEFA” is displayed.
3. Press the UP and DOWN buttons at the same time.
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 15ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 14
UV 72IP WiFly Set Up
UV 72IP
UC IR & Airstream App Control
With this feature you are able to control the unit with DMX without the
need of XLR cables. Your DMX controller must be connected to a ADJ
WiFly TransCeiver to use this function. You are able to communicate
up to 2500 feet/760 meters (open line of sight).
1. Turn on the WiFly function using the instructions on page 14.
2. Follow the instructions on page 14 to set the Wireless address.
The address must match the address set on the WiFly Transceiver.
3. After you have set the WiFly address, follow the DMX instructions
on page 12 to select your desired DMX Channel mode and set
your DMX address.
4. Apply power to the ADJ WiFly Transceiver. The fixture must be set
up first before you apply power to WiFly Transceiver.
Note: If the sync does not work, switch the WiFly power off then on
again.
UV 72IP WiFly Master-Slave Set Up
This feature will let you link units to run in a master-slave mode without the use of XLR cables.
1. Follow the instructions on page 14 to set the Wireless address.
The addresses on each fixture must be the same.
2. After you have set the WiFly address, select your master unit and
set your desired operating mode.
3. Turn on the WiFly function using the instructions on page 14.
4. For the Slave units, put the unit in Slave mode. See page 15
Master-Slave configuration when setting the unit as a Slave. Then
switch ON the WiFly power.
NOTE: If they do not sync up master-slave, switch the Master fixtures WiFly off then on again.
The UC IR infrared remote gives you control of various functions. To
control the fixture you must aim the remote at the front of the fixture
and be no more than 30 feet away. To use the ADJ UC IR you must
first activate the fixtures infrared sensor, to activate the sensor please
see the instructions on page 13.
The Airstream IR remote transmitter plugs into the headphone jack
of your iOS phone or tablet. To control your IR fixture you must raise
the volume to the maximum on your iOS phone or tablet and aim the
transmitter at the fixture sensor and be no more than 15 feet away.
After you have purchased the Airstream IR transmitters, the app is a
free download from the app store for your iOS phone or tablet. The
app comes with 3 pages of control depending on the fixture you are
using. Please see below for IR functions including the corresponding
app page.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture.
FULL ON - Pressing this button will fully light up the unit.
FADE/GOBO - Press this button to activate fade mode. Use but-
tons 1-4 to select your desired fade speed. 1 being the slowest fade
speed and 4 being the fastest fade speed.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity.
STROBE - Press this button to activate strobe mode. Use buttons
1-4 to select your desired strobe speed. 1 being the slowest strobe
speed and 4 being the fastest strobe speed.
COLOR - Press this button to activate UV Dimmer mode. Adjust the
output intensity using the “DIMMER +” and “DIMMER -” buttons.
1-4 - When in either fade mode or strobe mode, these buttons will
allow you to adjust the fade speed and strobe speed.
SHOW 0 - This button is invalid for this fixture.
SOUND ON & OFF - These button’s are invalid for this fixture.
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 17ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 16
DIMMER
UV 72IP
UC IR Remote & Airstream IR Receiver
UV 72IP Dimmer Curve Chart
100%
50%
10%
0%
0 Sec
Dimming Curve
Ramp Effect
Rise Time Down Time
0 sec Fade Time 1 sec Fade Time
255 255
Time (ms)
UV 72IP Power Linking
With this feature you can connect the xtures to one another
using a IP rated connector cable (sold separately). The quantity
that can be connected is 14 xtures maximum @ 120V and 24
xtures maximum @ 240V. After the maximum amount of xtures
have been reached you will need to use a new power outlet.
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES
TO THE UV 72IP AS THE POWER CONSUMPTION OF OTHER
LIGHTING FIXTURES WILL VARY!
UV 72IP Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
UV 72IP Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
0 0
Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)
Standard (default) 0 0 0 0
Stage 780 1100 1540 1660
TV 1180 1520 1860 1940
Architectural 1380 1730 2040 2120
Theatre 1580 1940 2230 2280
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 18 ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 19
UV 72IP Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect
Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par
Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
•LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-
ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
•StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited warranty).
•ADJDMXControllers=2Year(730Days)LimitedWarranty
UV 72IP Notes
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 20 ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 21
UV 72IP Specifications
Model:
Voltage: 100V ~ 240V/50~60Hz
LEDs: 24 x 3W UV LEDs
IP Rating: 65
Wavelength: 390-410nm
Beam Angle: 60 Degrees
Working Position: Any safe working position
Power Draw: 84W
Multiple Unit Power Link: 14 Fixtures Max. (120V)
24 Fixtures Max. (240V)
Weight: 12lbs./ 5.5 Kgs.
Dimensions: 10.5” (L) x 13.75” (W) x 15” (H)
270 x 350 x 380mm
Colors: UV
DMX Channels: 3 DMX Modes: 1/2/3
Warranty: 2 Year (730 days)
UV 72IP
Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC - www.adj.com - UV 72IP User Manual Page 22
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...