Utopia 250S™ General Information
American DJ®
User Instructions
Unpacking: Thank you for purchasing the Utopia 250S™ by Ameri-
can DJ
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fi xture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without fi rst contacting customer support.
Introduction: This unit use a single color/gobo wheel combination for
vibrant colors and extravagant gobo patterns. The Utopia 250S™ is an
intelligent fixture that can run In DMX mode, as a stand alone sound
active piece, or in a Master/Slave configuration. The Utopia 250S™
comes with several build in programs and is best used in multiples of
four. This piece is best used with a fog or haze machine to enhance
the beam output. When used in DMX mode channel 4 access a special strobe function. When used as a stand alone unit or when used
in multiples linked in a master/slave configuration an optional Utopia/C
controller may be used. The optional controller will access different programs and control a blackout function.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacifi c Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2610
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or fi re, do
not expose this unit to rain or moisture.
®. Every Utopia 250S™ has been thoroughly tested and has
Revised 9/01
American DJ
4295 Charter Street
Los Angeles CA. 90058
www.americandj.com
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
your nearest American DJ® dealer.
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 2
Utopia 250S™ General Instructions
Utopia 250S™ Safety Precautions
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this
manual with the unit, for future reference.
Utopia 250S™ Product Registration
The Utopia 250S™ carries a one year (365 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
If the unit is under warranty, you must provide a copy of your proof
of purchase invoice. Please contact American DJ® customer support
for a R.A. number.
Utopia 250S™ Features
• Micro-Stepping Motors for Smooth Color and Gobo Transitions
• DMX-512 Protocol Compatible (Uses Four DMX Channels)
• Full Manual Focusing
• Fan Cooled.
• 17 Color/Gobo Combinations Plus Spot.
• Master/Slave Operation
• Internal Microphone with Volume Sensitivity Knob
• Easy Lamp Replacement
• ZB-ELC 24v/250w Lamp
• Variable Speed Strobe Function
• Optional Utopia/C Remote Controller
Utopia 250S™ Halogen Lamp Warning
This fixture is fitted with halogen lamps which are
highly susceptible to damage if improperly handled.
Never touch the lamps with your bare fingers as
the oil from your hands will shorten lamp life. Also,
never move the fixture until the lamps have had
ample time to cool. Remember, lamps are not covered under warranty conditions.
• To reduce the risk of electrical shock or fi re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required voltage
for your unit.
• Do not attempt to operate this unit if the power cord has been frayed
or broken.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fi re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product outdoors
voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 7 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (includ ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 3
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 4
Utopia 250S™ Controls and Functions
REAR
1
2
3
4
5
1 2 3 4
ON
1 2 3 4 5 6 7 8 9
ON
7
6
7
8
9
10
11
FRONT
12
Utopia 250S™ Controls and Functions
1. Thumb Screw - This thumb screw holds the lamp socket assembly
cover (16) into place.
2. Microphone - This microphone receives external low frequencies
to trigger the unit in Sound-Active and Master/Slave mode.
3. Audio Sensitivity Knob - This adjust audio sensitivity of the
internal microphone (3). Turning the sensitivity knob in the clockwise
direction will increase the sensitivity to sound. Turning the knob in
the counter clockwise direction will decrease the fi xture’s sensitivity
to sound.
4. Option Switches - These switches will activate one of four
options:
Switch 1: Focus - When activated this switch will center the mirror
with a white spot. This will allow you to focus the beam
properly.
Switch 2: Sound Active - Turning this switch to the on position will
activate sound-active mode.
Switch 3: Inverted Pan - When activated this switch will invert the
PAN value. Left will become right and vice versa.
Switch 4: Inverted Tilt - When activated this switch will invert the
TILT value. Up will become down and vice versa.
13
14
1
15
5. Dip Switches - These switches serve two functions. In master
slave mode these switches are used to assign a specifi c head
address. In DMX mode these switches are used to assign a DMX
address to the unit. In DMX mode each switch corresponds to a
specifi c value based on binary code. See page 7 for a detailed
explanation of DMX binary code.
6. Power Indicator - This light will fl ash when the unit is in use.
7. Utopia/C Controller Jack - This jack is for use with the optional
Utopia/C Blackout controller only. Do not attempt to connect an audio
signal this jack, this will damage the PC board and void your manufactures warranty!
8. XLR Input Jack - This jack is used to accept an incoming DMX
signal or Master/Slave signal.
9. XLR Output Jack - This jack is used to transmit the incoming
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 6©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 5
Utopia 250S™ Controls and Functions Utopia 250S™ Operation
DMX signal to another DMX fi xture, or transmit a Master/Slave signal
to the nest Utopia 250S™ in the chain. For best results in DMX or
Master/Slave mode terminate this jack if it is the last unit in the
chain. See “Terminator” on page 7.
10. Fuse Holder - This housing stores the 3 amp GMA protective
fuse. Always replace with the exact same type fuse, unless other
wise instructed, by an authorized American DJ
® service technician.
11. Power Cord - Connect only to a matching power outlet. Never use
this fi xture is the ground prong has been removed or broken off.
12. Mirror - This is a highly refl ective surface mirror specifi cally
designed to optimize and enhance beam output. Never use glass
cleaner that contain ammonia to clean the surface of the mirror (such
as Windex).
13. Lens - This is a fully focusing high quality lens. Focus the lens by
manually turning the lens in a clockwise or counter-clockwise direction.
14. Lamp Socket Assembly - This assembly holds a ZB-ELC
(24v/250w) lamp. A long life version of lamp may be used in place of
the original lamp (ZB-ELC3 300 hours).
15. Lamp Socket Assembly Plate - This plate accesses the lamp
socket assembly.
Utopia 250S™ Operation
on pages 5 - 7 as well as the set-up specifications that are included
with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. When using a DMX controller and setting up for DMX operation
follow the dip switch settings on page 14.
6. For help operating in DMX operation consult the manual included
with your DMX controller.
7. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
Stand-Alone Operation (Sound Active): This function allows a
single unit to run to the beat of the music. Only use this function when
running a single unit, or when running several units as individuals.
1. To activate the Sound-Active mode be sure the number 2 function
switch is set to the “ON” position and refer to “Master Unit” on the
Master-Slave DIP SWITCH chart on page 14).
2. The unit will now react to the low frequencies of music via the inter nal microphone.
3. Adjust the audio sensitivity knob on the top of the unit to make the
unit more or less sensitive to sound. Turning the sensitivity knob in
the clockwise direction will increase the sensitivity, turning the knob
in the counter-clockwise direction will decrease the fi xture’s sensi tivity to sound.
4. The optional Utopia/C Blackout Controller may be used with this
function for blackout.
Universal DMX Control: This function allows you to use a universal
DMX 512 controller as the American DJ® DMX Operator™ or Show
Designer.™ to control mirror movement and the color/gobo wheel. The
use of a DMX controller will allow you to customize the use of fixtures
allowing you to control the rotation direction as well as the rotation
speed. Operating through a DMX controller allows the freedom to
create unique programs tailored to one’s individual needs.
1. The Utopia 250S™ uses four DMX channels. Channel 1 controls
pan, channel 2 controls tilt, channel 3 controls the color/gobo
wheel, and channel 4 controls the strobe function. See page 14 for
detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
Master-Slave Operation (Sound Active): This function will allow
you to link up to 4 units together and operate without a controller. The
units will be sound activated. In Master-Slave operation one unit will act
as the controlling unit and the others will react to the controlling units
programs. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connector on the rear of the units. Remember
the Male XLR connector is the input and the Female XLR connector
is the output. The fi rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a terminator
at the last fixture.
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 8©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 7
Utopia 250S™ Operation
2. Follow the chart on page 14 for proper unit dip switch settings.
3. The optional Utopia/C Blackout Mini-Controller may be used with
this function for blackout.
4. After all the units settings have been set and are plugged in, adjust
the sensitivity knob on the rear of the master unit to make them
react to sound.
Note: In Stand-Alone and Master-Slave operation the units will blackout
to conserve bulb life when a sound source is not received.
Utopia 250S™ Set Up
Power Supply: Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ®
Utopia 250S.™ The American DJ® Utopia 250S™ is available in a 120v
and 220v version. Because line voltage may vary from venue to venue,
you should be sure your unit voltages matches the wall outlet voltage
before attempting to operate you fi xture.
DMX-512: DMX is short for Digital Multiplex. This is a universal
protocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that
travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR
terminals located on all DMX fixtures (most controllers only have a
DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fi xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX
fixtures try to use the shortest cable path possible. The order in which
fixtures are connected in a DMX line does not influence the DMX
addressing. For example; a fixture assigned a DMX address of 1 may
be placed anywhere in a DMX line, at the beginning, at the end, or
anywhere in the middle. When a fixture is assigned a DMX address of
1, the DMX controller knows to send DATA assigned to address 1 to
that unit, no matter where it is located in the DMX chain.
Dip-switches in DMX mode: This unit uses dip switches to assign a
DMX address. Each dip switch represents a binary value.
Utopia 250S™ Set Up
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
DMX CHANNEL
12828 32
SP
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
ON
198765432 10
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
256651641
Dip Switch 10 - Some unit omit dip switch 10, when a unit does
included dip switch 10 it is used for special functions such as sound
activation.
Each dip switch has a preset value. A specific DMX address is set by
combining the dip switches that sum your desired value. For example:
To achieve a DMX address of 21, combine dip switches 1, 3, and 5.
Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4,
and dip switch 5 has a value of 16, the combination of the create a
DMX value of 21.
Set DMX address 21: Set DMX address 201:
Dip-switches # 1 = 1 Dip-switches # 1 = 1
3 = 4 4 = 8
5 = 16 7 = 64
= 21 8 = 128
= 201
Data Cable (DMX Cable) Requirements (For DMX and Master/
Slave Operation): The Utopia 250S™ can be controlled via DMX-512
protocol. The American DJ® Utopia 250S™ is a four channel DMX unit.
The DMX address is set on the front panel of the Utopia 250S™. Your
unit and your DMX controller require a standard
3-pin XLR connector for data input and data output
(Figure 1). If you are making your own cables, be
sure to use standard two conductor shielded cable
(This cable may be purchased at almost all pro
sound and lighting stores). Your cables should be
made with a male and female XLR connector on
either end of the cable. Also remember that DMX
cable must be daisy chained and can not be split.
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 10©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 9
Figure 1
Utopia 250S™ Set Up
Utopia 250S™ Fuse & Lamp Replacement
Notice: Be sure to follow fi gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
1
DMX512 IN
3
3-PIN XLR
2
Figure 2
XLR Pin Confi guration
1 Ground
3 Hot
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
XLR Male Socket
1 Ground
Figure 3
DMX512 OUT
3-PIN XLR
2 Cold
3 Hot
1
3
2
DMX +
DMX -
XLR Female Socket
2 Cold
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
5-Pin XLR DMX Connectors.
connectors for DATA transmission in place of 3-pin. 5-pin XLR fi xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Some manufactures use 5-pin XLR
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
Caution: Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ® technician.
Replace with anything other than the specified part can damage your
unit and will void your manufactures warranty.
Warning: If, after replacing the lamp or fuse either one continues
to blow, STOP using the unit. Contact customer support for further
instructions, you may have to return the unit for servicing. Continuing
to use the unit may cause serious damage.
Fuse Replacement: Disconnect the unit’s main power supply. Insert
a standard flat head screw driver in to the fuse holder housing. Turn
the screwdriver in counter-clockwise direction to remove the fuse
holder. Remove the fuse holder to expose the fuse. Remove the old
fuse and discard it. Replace the fuse with the same type. Insert the
fuse holder back into it’s housing and turn it in clockwise direction to
lock the holder in place.
Lamp Replacement: Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power and
allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up front cover that is retained by thumb screws.
1. Be sure to follow the proper handling procedures that deal
with halogen lamps.
2. Remove the thumb screw on the top/rear of the unit that holds the
lamp socket assembly cover in place.
3. After removing the thumb screw, slide out the cove from the rear of
the unit to expose the lamp socket assembly.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble in reverse
order.
Lamp Socket
Assembly
Thumb Screws
Lamp Cover
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 11 ©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 12
Utopia 250S™ Cleaning
Utopia 250S™ DMX Traits
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside
casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft
cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
Utopia 250S™ Trouble Shooting
Trouble Shooting: Listed below are a few common problems that you
may encounter, with solutions.
No light output from the unit;
This chart below details the DMX traits. The individual trait can only be
accessed an universal DMX controller.
DMX CHANNEL
12
PAN TILT COLOR/GOBO STROBE
145˚255
73˚128
0˚
0
90˚255
45˚128
0
0˚
3
White/Lg Spot 248-255
Strobe 8fps 247
Strobe 2fps 208
Fast Rotation 207
Slow Rotation 160
Gobo 17/Ylw-Lt Blue
Gobo 16/Purple 144-151
Gobo 15/Blue 136-143
Gobo 14/Lt Blue 128-135
Gobo 13/Green 120-127
Gobo 12/Yellow 112-119
Gobo 11/Red 104-111
Gobo 10/White 96-103
Gobo 9/4-Colors 88-95
Gobo 8/Purple-Wht 80-87
Gobo 7/Red-Green 72-79
Gobo 6/Purple 64-71
Gobo 5/Blue 56-63
Gobo 4/Lt Blue 48-55
Gobo 3/Green 40-47
Gobo 2/Yellow 32-39
Gobo 1/Red 24-31
Blackout 16-23
Lrg Spot/White 08-15
Blackout 01-07
Lamp Off 00
152-159
Strobe 1fps 255
Strobe 7fps 129
Strobe 7fps 128
Strobe 1fps 01
Stop 00
This chart details the gobo pattern as well
as the gobo wheel placement.
4
Strobe Step Up
Strobe Step Down
1. Be sure you have connected your unit into a standard 120V wall
outlet.
2. Be sure the external fuse has not blown. The fuse is located on the
bottom panel of the unit.
3. Remove the lamp cover and be sure the lamp is seated in its
socket properly. Occasionally lamps become loose during shipping
be sure the lamp is push in to its socket all the way.
4. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Ta p pin g on t h e microphone, quiet or high pitched sounds may not
activate the unit.
2. Be sure the SENSITIVITY KNOB (5) is not set to the minimum
position
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 13
Utopia 250S™ Master/Slave Settings
This chart details the Master/Slave dip switch setting for Master/Slave
configuration. Use this configuration only when you will be using your
fixtures in a Master/Slave configuration. Be sure the number 2 function
switch is set to the on position for sound-active operation.
ON
ON
1432
Function Switch
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 14
198765432
Master - Head 1
ON
198765432
Head 3
ON
198765432
Head 2
ON
198765432
Head 4
Utopia 250S™ DMX Dip Switch Chart
Technical Specifications:
This chart list the DMX dip switch setting for DMX address 1 through
511. Follow the instructions below to configure fixture dip switches with
your desired DMX address.
DMX Address Quick Reference Chart
DIP SWITCHES
Dip Switch Position
DMX DIP Switch Settings
X = OFF
O = ON
#1 #2 #3 #4 #5
XXXX
O XXXX
XOXXX
OOXXX
XXOXX
OXOX X
X OOX X
OOOXX
XXXOX
O XXOX
XOXOX
OOXOX
XXOOX
OXOOX
X OOOX
OOOOX
XXXXO
O XXXO
XOXXO
OOXXO
XXOXO
Dip Switch Position
OXOX O
X OOX O
OOOXO
XXXOO
O XXOO
XOXOO
OOXOO
XXOOO
OXOOO
X OOOO
OOOOO
#9
#8
#7
#6
X
36496128160192224 256 28832035 2 384 416 448 480
1336597129161193225 257 289321353 385 417 449 481
2346698130 162 194 2 26 258 290 322 354 386 4 18 450 482
3356799131163195227 259 291323355 387 419 451 483
43668100132 164 196 228 260 292 324 356 388 420 452 484
53769101 133 165 197 229 261 293 325 35 7 389 421 453 485
63870102134 166 198 230 262 294 326 358 390 422 454 486
73971103135 167 199 231 263 295 327 359 391 423 455 487
84072104 136 168 200 232 264 296 328 36 0 392 424 456 488
94173105137 169 201 233 265 297 329 361 393 425 457 489
10 42 74 106 138 170 202 234 266 298 330 362 394 4 26 458 490
11 4 3 7 5 107 139 17 1 203 235 267 299 331 36 3 395 427 459 491
12 44 76 108 140 172 204 236 268 300 332 364 396 4 28 460 492
13 45 77 109 141 173 205 237 269 301 333 365 397 4 29 461 493
14 46 78 110 142 174 206 238 270 302 334 366 398 430 4 62 494
15 47 79 111 143 175 207 239 271 303 335 367 399 4 31 463 495
16 48 80 112 144 176 208 240 272 304 336 368 400 4 32 464 496
17 49 81 113 145 177 209 241 273 305 337 369 401 433 4 65 497
18 50 82 114 146 178 210 242 274 306 338 370 402 4 34 466 498
19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499
20 52 84 116 148 180 212 244 276 308 340 372 404 436 4 68 500
21 53 85 117 149 181 213 245 277 309 341 373 405 4 37 469 501
22 54 86 118 150 182 214 246 278 310 342 374 406 4 38 470 502
23 55 87 119 151 183 215 247 279 311 343 375 407 439 4 71 503
24 56 88 120 152 184 216 248 280 312 344 376 408 4 40 472 504
25 57 89 121 153 185 217 249 281 313 345 377 409 4 41 473 505
26 58 90 122 154 186 21 8 2 50 282 314 346 378 410 4 42 474 506
27 59 91 123 155 187 219 251 283 315 347 379 411 4 43 475 507
28 60 92 124 156 188 220 252 284 316 348 380 412 4 44 476 508
29 61 93 125 157 189 22 1 2 53 285 317 349 381 413 4 45 477 509
30 62 94 126 158 190 222 254 286 318 350 382 414 4 46 478 510
31 63 95 127 159 191 223 255 287 319 351 383 415 447 4 79 51
O
DMX Address
The center numbers of this chart (1-511) represent a DMX address. The "X"'s
and "O"'s along the top and side of the chart represent dip switch poistion ("X"
for off and "O" for on). Find your desired DMX address from the center chart.
Identify the position for dip switches 1-5 from the chart on the left and dip
switches 6-9 from the chart on the top. Adjust the dip switches on your fixture to
match the position settings of the chart. For fixtures with 10 dip switches; dip
switch 10 is reserved for special functions.
©American DJ® - www.americandj.com - Utopia 250S™ Instruction Manual Page 15
OOOOOXOOOXXXXXXX
OOOOOOOOXXXXXX XX
OXOXOOXXOOXX XXOO
XOXXOOOXOXXOXOX
DMX Address
1
Model: Utopia 250S™
Lamps: ZB-ELC, 24v/250w
Voltage: 120v/60Hz or 220v/50Hz
Dimensions: 20”(H) x 8.5”(W) x 9.25”(D)
with yoke collapsed
Colors Multiple
Gobos: 17, plus spot
Weight: 25 Lbs.
Fuse: 5A GMA (120v)/3A GMA (220v)
Duty Cycle: 30 min on / 5 min off
DMX: 4 Channels
Sound Active: Yes
Working Position: Any Safe, Secure Position
Warranty: 1 Year (365 days)
Please Note: Specifi cations and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
A Division of the American DJ® Group of Companies
©American DJ® World Headquarters:
4295 Charter Street Los Angeles, CA 90058 USA
Tel: 323-582-2650 Fax: 323-582-2610
Web: www.americandj.com E-mail: info@americandj.com
Loading...