American DJ Torch Light User Instructions

Rev 10/01

Los Angeles Ca. 90058

www.americandj.com

4295 Charter Street

American DJ

User Instructions

The shipping carton and packing materials are constructed of

recyclable material, please recycle when ever possible.

©American DJ Supply® - www.americandj.com - Torch Light™ Instruction Manual Page 2

your nearest American DJ

® dealer.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

Warning! To prevent or reduce the risk of electrical shock or fi re, do

not expose this unit to rain or moisture.

3-6 month of use to maintain the orginal effect.

Customer Support: American DJ

® provides a toll free customer sup-

without the heat. The simulated flame effect is further enhanced by the

case design that is designed to look like an ancient torch. This unit uses

a silk drape cut out in the shape of a flame that must be replace every

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may also

visit us on the web at www.americandj.com for any comments or sug-

gestions. Service Hours are Monday through Friday 9:00 a.m. to 5:00

p.m. Pacifi c Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]

for future reference. The Torch Light™ produces a unique flame effect

Torch Light™ General Introduction

Unpacking: Thank you for purchasing the Torch Light™ by American

DJ®. Every Torch Light™ has been thoroughly tested and has been

shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton

appears to be damaged, carefully inspect your unit for any damage

and be sure all equipment necessary to operate the unit has arrived

intact. In the event damage has been found or parts are missing, please

contact our toll free customer support number for further instructions.

Please do not return the unit to your dealer without fi rst contacting cus-

tomer support.

Introduction: Please carefully read and understand the instructions in

this manual thoroughly before attempting to operate this unit. These

instructions contain important safety information regarding the proper

use and maintenance of this unit. Please keep this manual with the unit,

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall

• Do not attempt to operate this unit, if it becomes damaged

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties

• During long periods of non-use, disconnect the unit’s main power

• Always mount this unit in safe and stable matter

• Power cords should be routed so they are not likely to be walked on,

pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 7 for cleaning details

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a

marked change in performance.

• Never plug this unit in to a dimmer pack

wise instructed by an authorized American DJ

® service technician. Use

of a different type fuse from that which is recommended may cause fire

or electric shock and will void the manufactures warranty.

• To reduce the risk of electrical shock or fi re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit

• Do not attempt to operate this unit if the power cord has been frayed

or broken

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and fi re in case of an internal short

• Disconnect from main power before making any type of connection

• Do not remove the cover under any conditions. There are no user

serviceable parts inside

Safety Issues: This unit may blow a fuse if the maximum allotted

load of 3 amps is reached. If the fuse needs replacement, always

replace the fuse with same exact type that was remove, unless other-

Torch Light™ Safety Warnings

Silk Flame:

Your silk fl ame has been specially designed and hand cut from the fi nest

silk to interact with the airfl ow and lights to create the illusion of a fl ame.

Each silk drape is applied prior to shipment and should be in the cor-

rect position. The silk drape has a life of approximately one month when

used continuously in a clean environment. Additional silk drapes may be

purchased through your dealer (part number z-torch/silk).

©American DJ Supply® - www.americandj.com - Torch Light™ Instruction Manual Page 4©American DJ Supply® - www.americandj.com - Torch Light™ Instruction Manual Page 3

1. Remove all packing materials from the Torch Light.

2. Place the Torch Light™ on a fl at level surface.

3. Optional wall mount brackets are available for this unit. These

bracket allow the unit to mounted in almost any location. Please

contact American DJ or see your dealer for more information.

4. Plug the power cord into a grounded electrical outlet with a match-

ing power supply.

5. Turn the power switch on rear of unit to “ON” position.

Lamps:

The positioning of the lamps is pre-set and does not require any type of

adjustment. Improperly positioned lamps will create deep spots of color

in the fl ame. Should the lamps need adjustment due shifting during

transit or after the replacement of a lamp, the lamps may be angled

slightly to overcome any heavy color wash. Should the lamps position-

ing become incorrectly, adjust them as follows:

1. To properly position the lamp the unit must be on. Use an insulated

screwdriver to make any adjustment to the lamps position.

2. The amber lamps should be angled to focused on the lower half of

the silk drape.

3. Position the blue lamp to shine directly in the center of silk drape.

4. All lamps will eventually fade or fail. Replacements lamps are avail-

able from your dealer.

and do not attempt to use. Please contact your dealer for assistance.

Torch Light™ Set-Up/Operation

Unit Preparation:

Before beginning initial setup of your Torch Light Flame Machine, make

sure there is no evident damage caused during transportation. In the

event that the unit’s housing or cable is damaged, do not plug the unit in