American DJ Star Winder User Instructions
Star Winder™ Introduction
General Instructions: Thank you for purchasing the American
DJ® Star Winder.™ The Star Winder™ is an intelligent moon-ower effect
with a twist. This unit uses a multi-colored dichroic dish overlapped
with a slotted dish. The two dish rotate against each other to create an
unique cross effect. To optimize the performance of this product, please
read these operating instructions carefully to familiarize yourself with
the basic operations of this unit. This unit is sound-active and may be
operated with or without an universal DMX controller such as the American DJ® DMX Operator™ or Show Designer.™ The unit can be linked
with several other units to run in a Master/Slave orientation. For best
result use this xture with fog to enhance the beam output.
Customer Support: American DJ® provides a toll free customer
support line, to provide set up and installation help and to answer any
question should you encounter problems during your set up or initial
operation. You may also visit us on the web at www.americandj.com
for any comments or suggestions. Toll free customer service hours are
Monday through Friday 9:00 a.m. to 5:00 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2610
E-mail: support@americandj.com
User Instructions
American DJ
4295 Charter Street
Los Angeles Ca. 90058
www.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any type of repair yourself without the manufactures consent,
doing so will void your manufactures warranty. In the unlikely event your
unit may require service, contact American DJ® customer support.
Warning! The 1/4” phone plug on the unit is for the optional
MINI/C. Do not attempt to connect an audio signal to this jack, this
will damage the PC board and void your manufactures warranty!
Star Winder™ Halogen Lamp War ning
This xture is tted with a halogen lamp which is highly susceptible to
damage if improperly handled. Never touch the lamp with your bare
ngers as the oil from your hands will shorten the lamp life. Never
install, mount, or place this xture in areas prone to heavy vibration.
Also, never move the xture until the lamp has had ample time to cool.
Remember, lamps are not covered under warranty conditions.
©American DJ Supply® - www.americandj.com - Star Winder™ Instruction Manual Page 2
Star Winder™ Contents
Star Winder™ Safety Precautions
Introduction...................................................................................2
Unpacking....................................................................................3
Features..................................................................................3
Safety Precautions.......................................................................4
Set-Up................................................................................5
DMX Addressing.............................................................6
Linking...............................................................................7
Controls & Functions..........................................................8
Operation..............................................................................9
Lamp Replacement..............................................................11
Foc usi ng. ... ....... ... ... ... ....... ... ... ... .... ... ... ... ... .... ... ..1 2
Cleani ng ...... ....... .. ...... ....... .. ...... ...... ....... .. ...... ....... 12
Dip Switch Charts...............................................................13
Warranty.........................................................................15
Star Winder™ Unpacking
Every Star Winder™ has been thoroughly tested and has been shipped
in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect your xture for any damage and be
sure all equipment necessary to operate the unit has arrived intact. In
case damage has been found or parts are missing, please contact our
toll free customer support number for further instructions, please do not
return the unit to your dealer.
Star Winder™ Features
• Vibrant Color Wheel.
• Linkable.
• Audio Sensitivity Knob.
• Uses One DMX Channels.
• Sound-Active.
• DMX-512 Protocol Compatible.
• Full Focusing.
• Master/Slave Built-In Programs.
• Fan Cooled.
• Optional MINI/C Blackout Controller.
©American DJ Supply® www.americandj.com Star Winder™ Instruction Manual Page 3
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required voltage
for your unit.
• Do not attempt to operate this unit if the power cord has been frayed
or broken.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the top cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged in any way.
• Never operate this unit when it’s cover is removed.
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product outdoors
voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power Cord Protection - Power supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the appliance.
• Cleaning -The xture should be cleaned only as recommended by
the manufacturer.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (includ ing ampliers) that produce heat.
• The xture should be serviced by qualied service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
©American DJ Supply® www.americandj.com Star Winder™ Instruction Manual Page 4
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal erro rs and
avo ids signa l tran smi ssi on problems
and interference. It is always advis able
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Star Winder™ Set Up
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
1
2
3
Termination reduces signal erro rs and
avo ids signa l tran smi ssi on problems
and interference. It is always advis able
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Star Winder™ Set Up
Power Supply: Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ®
Star Winder.™ The American DJ® Star Winder™ is available in a 120v
and 220v version. Because line voltage may vary from venue to venue,
be sure to plug your unit into a matching wall outlet before attempting
to operate.
Data Cable (DMX Cable) Requirements (For DMX Operation
Only and Master-Slave): The Star Winder can be controlled via
DMX-512 protocol. The American DJ® Star Winder™ is a three channel
DMX unit. The DMX address is set on the front panel of the Star Winder.
Your unit and your DMX controller require a standard 3-pin XLR connector for data input and data
output (Figure 1). If you are making your own
cables, be sure to use standard two conductor
shielded cable (This cable may be purchased at
almost all pro sound and lighting stores). Your
cables should be made with a male and female
XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained
Figure 1
and can not be split.
Notice: Be sure to follow gure three when making your own cables.
Do not use the ground lug on the XLR connector. Do not connect the
cable’s shield conductor to the ground lug or allow the shield conductor
to come in contact with the XLR’s outer casing. Grounding the shield
could cause a short circuit and erratic behavior.
XLR Male Socket
1 Ground
2 Cold
3 Hot
XLR Female Socket
2 Cold
1 Ground
3 Hot
XLR Pin Conguration
Pin 1 = Shield
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last unit
in your daisy chain to terminate the line. Using a cable terminator (ADJ
part number ZDMX/T) will decrease the possibilities of erratic behavior.
Figure 4
Star Winder™ DMX Addressing
DMX is short for Digital Multiplex. This is a universal binary language
used as a form of communication between intelligent fixtures. Each dip
switch represents a binary value.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
ON
DMX CHANNEL
2 8 32 128
1 2 3 54 7 986
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
1 4 16 64 256
Each dip switch has a preset value, a desired DMX address is set by
combining the dip switches that will create your desired value. For
example: To achieve a DMX address of 21, combine dip switches 1, 3,
and 5. Sense dip switch 1 has a value of 1, dip switch 3 has a value
of 4, and dip switch 5 has a value of 16, the combination of the create
a DMX value of 21.
©American DJ Supply® - www.americandj.com - Star Winder™ Instruction Manual Page 5 ©American DJ Supply® - www.americandj.com - Star Winder™ Instruction Manual Page 6
Figure 2
Figure 3
Set DMX address 21: Set DMX address 201:
Dipswitches # 1 = 1 Dipswitches # 1 = 1
3 = 4 4 = 8
5 = 16 7 = 64
= 21 8 = 128
= 201
Loading...