American DJ Starball II User Manual

Revised 02/02

Los Angeles Ca. 90058

www.americandj.com

4295 Charter Street

American DJ®

American DJ®

Starball II

User Instructions

cian. Use of a different type fuse from that which is recommended may

cause fire or electric shock and will void the manufactures warranty.

otherwise instructed by an authorized American DJ

©American DJ Supply® - www.americandj.com - Starball II™ Instruction Manual Page 2

® service techni-

Safety Issues: This unit may blow a fuse if the maximum allotted

load of 2 amps is reached. If the fuse needs replacement, always

replace the fuse with same exact type that was remove, unless

PLEASE do not discard the shipping carton in the trash. Please

recycle when ever possible.

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

your nearest American DJ dealer.

Caution! There are no user serviceable parts inside this unit. Do not

Warning! To prevent or reduce the risk of electrical shock or fi re, do

not expose this unit to rain or moisture.

related issue please contact American DJ®. Service Hours are Monday

through Friday 9:00 a.m. to 5:00 p.m. Pacifi c Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]

American DJ® provides a toll free customer support line, to provide set

Customer Support:

return the unit to your dealer without fi rst contacting customer support.

all equipment necessary to operate the system has arrived intact. In the

event damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Please do not

perfect operating condition. Carefully check the shipping carton for

damage that may have occurred during shipping. If the carton appears

to be damaged, carefully inspect your unit for any damage and be sure

up help and to answer any question should you encounter problems

during your set up or initial operation. You may also visit us on the web

at www.americandj.com for any comments or suggestions. For service

Unpacking:

Thank you for purchasing the Starball II™ by American DJ®. Every

Starball II™ has been thoroughly tested and has been shipped in

Starball II™ Introduction

• Power-Cord Protection - Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to cords at

plugs, convenience receptacles, and the point where they exit from

the fixture.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer.

• The fixture should be serviced by qualified service personnel when:

A. The power cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

©American DJ Supply® - www.americandj.com - Starball II™ Instruction Manual Page 3

marked change in performance.

rain or moisture.

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

• During long periods of non use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• To reduce the risk of electrical shock or fi re, do not expose this unit

shock and fi re in case of an internal short.

for your unit.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

regarding the use and maintenance of this unit. Please keep this

• Be sure that the local power outlet match that of the required voltage

manual with the unit, for future reference.

Starball II™ Safety Precautions

To optimize the performance of this product, please read these operat-

ing instructions carefully to familiarize yourself with the basic operations

of this unit. These instructions contain important safety information

Starball II™ General Instructions

• Do not remove the unit cover under any conditions. There are no

user serviceable parts inside.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

out fi rst contacting customer support.

©American DJ Supply® - www.americandj.com - Starball II™ Instruction Manual Page 4

120v and 220v version. Because line voltage may vary from venue to

venue, be sure to plug your fi xture into a wall outlet with a matching

power supply before attempting to operate.

General Operation:

Simplicity! Just plug this fixture in, and watch it go. This fixture is

designed to operate as a stand alone unit, there is no need of a con-

troller. It has been tested and the lamp has been installed at the fac-

tory there is no assembly necessary. The Starball II™ is ready to be

plugged in, out of the box. There is no power switch, after plugging the

unit the unit will light up and begin to slowly rotate in a single direction.

If there is no lamp output check the fuse and bulb. If the fuse and bulb

are good, please contact our toll free customer support number for

further instructions. Please do not return the unit to your dealer with-

Power Supply: Before plugging your unit in, be sure the source

voltage in your area matches the required voltage for your American

DJ® Starball II.™ The American DJ® Starball II

™

Starball II™ Operation

• Built-In Mounting Plate

• Bright ZB-64514 (300w/120v) or ZB-64516 (300w/220v)

• Low Power Consumption (about 2 amps)

is available in a

• Air Cooled

Starball II™ Features

copy of your proof of purchase invoice. You may obtain a R.A. number

by contacting customer support at [phone].

• 235 Clear Beams

• 10 RPM Motor

• Easy Lamp Replacement

shipping container. If the unit is under warranty, you must provide a

Starball II™ Warranty Registration

The Starball II™ carries a one year (365 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase.

All returned service items whether under warranty or not, must be

freight pre-paid and accompany a return authorization (R.A.) number.

The R.A. number must be clearly written on the outside of the return

package. A brief description of the problem as well as the R.A. number

must also be written down on a piece of paper and included in the