American DJ MEGA BAR RGBA User manual

Mega Bar RGBA Introduction

Unpacking: Thank you for purchasing the Mega Bar RGBA by ADJ
Products, LLC. Every Mega Bar RGBA has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.

If the carton appears to be damaged, carefully inspect your xture for

any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are
missing, please contact our toll free customer support number for fur­ther instructions. Do not return this unit to your dealer without rst con­tacting customer support.

Introduction: The ADJ Mega Bar RGBA is a rechargeable lithium bat-

tery powered, DMX intelligent, LED bar fixture. This unit give you the
freedom to set up your fixture where ever you wish without the restric-

tions of power. The built-in battery will keep charge for up to 8 hours
(full on) from a full, single charge. This xture can be used in a stand
alone mode or connected in a Master/Slave conguration. This wash
has five operating modes: Sound Active mode, Auto mode, RGB mode,
Static Color mode, and DMX control mode.

Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or sugges­tions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.

Pacic Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]

1/13

User Instructions

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 2

Mega Bar RGBA Features

Mega Bar RGBA Safety Precautions

• Mulit-Colors

• Six Operating Modes

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• Seven DMX Modes: 4 Channel Mode, 6 Channel Mode, 7 Channel
Mode, 9 Channel Mode, 10 Channel Mode, 18 Channel Mode, and

34 Channel Mode.

• ADJ RFC compatiable (Not Included)

• Power Cord Daisy Chain (See page 23)

Mega Bar RGBA Warranty Registration

The Mega Bar RGBA carries a 3 year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All pack­ages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.

Mega Bar RGBA Installation

The unit should be mounted using a mounting clamp (not provided),

afxing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slip-

ping while operating. Always ensure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.

The equipment must be installed by a professional, and it must be

installed in a place where it is out of the reach of people’s grasp.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

t he manufacturer. See page 23 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (inclu­ d ing amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a

marked change in performance.

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 4ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 3

Mega Bar RGBA Set Up

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

Mega Bar RGBA Set Up

Power Supply: The ADJ Mega Bar RGBA contains a automatic volt­age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the fixture. DMX data is sent as serial data that trav­els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter­minals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compli­ant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):

The Mega Bar RGBA can be controlled via DMX-512 protocol. The
Mega Bar RGBA has 7 DMX channel modes, please see pages 9-10

for the different modes. The DMX address is set on the back panel of
the Mega Bar RGBA. Your unit and your DMX con­troller require a standard 3-pin XLR connector for
data input and data output (Figure 1). We recom­mend Accu-Cable DMX cables. If you are making

your own cables, be sure to use standard 110-120
Ohm shielded cable (This cable may be purchased

at almost all pro lighting stores). Your cables should
be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 5 ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 6

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

1 Ground

3 Hot

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

When longer runs of cable are

Figure 4

Pin 1

Pin 2

Pin 3

Do Not Use

Do Not Use

XLR Male Socket

1 Ground

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

DMX +

DMX -

XLR Female Socket

2 Cold

Figure 3

Special Note: Line Termination.

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

5-Pin XLR DMX Connectors.

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

Some manufactures use 5-pin DMX-

3-Pin XLR to 5-Pin XLR Conversion

Pin 1

Pin 2

Pin 3

Mega Bar RGBA Operating Instructions

Mega Bar RGBA Operating Instructions

LED Display On/Off:

To set the LED display to turn off after 20 seconds, press the MODE
and DOWN buttons at the same time. Now the display will disappear

after 20s. Press any button to turn the display on again. To allow the

display to stay On at all times, press the MODE and UP buttons at

the same time.

Operating Modes:

The Mega Bar RGBA has six operating modes:

• Sound-Active mode - The unit will react to sound, chasing through

the built in programs.

• Built-In Program - There are 22 built-in programs to choose from.

• Static Color Mode - There are 15 colors to choose from.

• Auto Mode - A auto program will run with adjustable fade speed.

• RGBA Mode - Choose one of the four colors to remain static or

adjust the intensity of each color to make your desired color.

• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.

Static Color Mode:

1. Plug the fixture in and press the MODE button until “C0.XX” is

displayed.

2. There are 15 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected

your desired color you can activate strobing by pressing the SET
UP button to enter the Flash (strobe) mode.

3. “FS.XX” will now be displayed, this is Flash mode. The Flash can
be adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).

RGBA Dimmer Mode:

1. Plug the fixture in and press the MODE button until “rgbA” is dis-

played. Then press the SET UP button to adjust intensity of the
individual colors.

2. When “r.XXX” is displayed you are in Red dimming mode. Press
the UP and DOWN buttons to adjust intensity.

3. When “G.XXX” is displayed you are in Green dimming mode.
Press the UP and DOWN buttons to adjust intensity.

4. When “b.XXX” is displayed you are in Blue dimming mode. Press
the UP and DOWN buttons to adjust intensity.

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 7

5. When “A.XXX” is displayed you are in Amber dimming mode.
Press the UP and DOWN buttons to adjust intensity.

6. After you have adjusted the RGBA colors to make your desired
color you can then activate strobing by pressing the SET UP but­ ton to enter the Flash (strobe) mode.

7. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).

Built-In Program Mode:

1. Plug the fixture in and press the MODE button until “Pr.XX” is dis­ played. “XX” represents a number from 1-22. Use the UP or DOWN
buttons to scroll through the 22 programs. Programs 21 and 22
have adjustable colors. Once you have found your desired program

press the SET UP button.

2. Pressing the SET UP button will display “SP.XX”. When this is dis-

played you can adjust the running speed of your desired program.

Use the UP or DOWN button to adjust the speed between “SP.01”
(slowest) and “SP.99” (fastest). Once you have set your desired run-

ning speed, you can press the SET UP button to to enter the Fade
adjustment mode.

2. Pressing the SET UP button will display “Fd.XX”. When this is dis-

played you can adjust the fade speed of your desired program.

Use the UP or DOWN button to adjust the speed between “Fd.01”
(fastest) and “Fd.99” (slowest) or “Fd.00” (Off). Once you have set

your desired fade speed, you can press the SET UP button to to
enter the Flash (Strobe) mode.

3. After pressing SET UP, “FS.XX” will be displayed, this is Flash mode.
The Flash can be adjusted between “FS.00” (flash off) to “FS.99”

(fastest flash).

• PROGRAMS 21 & 22 - If you have chosen programs 21 or 22, after
the Flash mode, press the SET UP button. “C1.XX” will be displayed.
This is the base color, use the UP and DOWN buttons to scroll
through the 15 colors. Once you have chosen your base color, press
the SET UP button again so that“C2.XX” is displayed. This is the
moving color, use the UP and DOWN buttons to scroll through the 15

colors.

Sound Active Mode:

In this mode the Mega Bar RGBA will react to sound, and chase
through the different colors.

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 8

Mega Bar RGBA Operating Instructions

Mega Bar RGBA Operating Instructions

1. Plug the fixture in and press the MODE button until “SU.XX” is
displayed. “XX” represents the sound sensitivity level.

2. Use the UP or DOWN buttons to adjust the sound sensitivity.
“SU.00” is off, “SU.01 is the lowest sensitivity, and “SU.31” is the

highest. After adjusting the sound sensitivity, press SET UP if you
wish to activate the Flash mode.

3. “FS.XX” will now be displayed, this is Flash mode. The Flash can
be adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).

Auto Run Mode:

In this mode the Mega Bar RGBA will run a auto program.

1. Plug the fixture in and press the MODE button until “AUTO” is dis-

played.

2. After you have activated Auto Run mode, press the SET UP but­ ton to adjust the fade time.

3. Once you press SET UP “Fd.XX” should be displayed. Use the UP
or DOWN buttons to set the fade speed to either “Fd.00” (fade
off) or between “Fd.01” (fastest speed) and “Fd.99” (slowest

speed). After adjusting the fade speed, press SET UP if you
wish to activate the Flash mode.

4. “FS.XX” will now be displayed, this is Flash mode. The Flash can
be adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).

DMX Mode:

Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Mega
Bar RGBA has 7 DMX modes: 4 Channel mode, 6 Channel mode,

7 Channel mode, 9 Channel mode, 10 Channel mode, 18 Channel
mode, and a 34 Channel mode. See pages 13-22 for each modes’

DMX traits.

1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.

2. To run your fixture in DMX mode press the MODE button until
“d.XXX” is displayed. “XXX” represents the current displayed ad­ dress. Use the UP or DOWN buttons to select your desired DMX

address, then press the SETUP button to select your DMX
Channel mode.

3. Use the UP or DOWN buttons to scroll through the DMX Channel

modes. The Channel modes are listed below:

To run the 4 Channel Mode, press the MODE button until “Ch.01”

is displayed. This is the 4 Channel DMX Mode.

To run the 6 Channel Mode, press the MODE button until “Ch.02”

is displayed. This is the 2 Channel DMX Mode.

To run the 7 Channel Mode, press the MODE button until “Ch.03”

is displayed. This is the 7 Channel DMX Mode.

To run the 9 Channel Mode, press the MODE button until “Ch.04”
is displayed. This is the 9 Channel DMX Mode.
To run the 10 Channel Mode, press the MODE button until
“Ch.05” is displayed. This is the 10 Channel DMX Mode.
To run the 18 Channel Mode, press the MODE button until
“Ch.06” is displayed. This is the 18 Channel DMX Mode.
To run the 34 Channel Mode, press the MODE button until
“Ch.07” is displayed. This is the 34 Channel DMX Mode.

4. Please see pages 13-22 for DMX values and traits.

5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-

ler.

Default Running Mode:

This is a default running mode. When this mode is activated all modes
will return to their default settings and a Auto program will run.

1. Plug the fixture in and press the MODE and SET UP buttons at the

same time.

ADJ RFC:

This function is used to activate and deactivate the ADJ RFC (Remote

Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see the next page for ADJ RFC controls

and functions.

1. Plug the fixture in and press the MODE button until “Auto” is dis-

played.

2. Press the SET UP button until “rF.XX” is displayed. “XX” repre­ sents either “on” or “oF”.

3. Press the UP or DOWN buttons to either activate the remote func­ tion (On) or deactivate it (Off).

ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 10ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 9