American audio RACK COLOR LED User Manual
American Audio - www.AmericanAudio.us
LOS ANDELES,CA.90058
Rack Color LED
User Instructions
Descriptions:
Congratulations with your purchase of this product.
Read this manual carefully before using our American Audio Rack Color LED. The is a 19''/1U RGB LED Bar
with rainbow effect, providing 24 in color RGB LEDs, designed for the Working DJ. All parameters and work modes can be set
up by LED remote operation.
Delivery Packet:
Check for transport damage.
You should be in possession of the following items:
Rack Color LED
1
1 Manual
1 LED Remote Control(Infrared Remote Control)
Rack Color LED
Should you discover transport damage after unpacking the equipment, inform the hauler immediately.
Never connect a damaged device. You may also contact your supplier.
Main Features:
- Easy-to-use 19'' LED bar used to light up your DJ rack(24 LEDs)
-LED Advantages: NO heat output, low power draw, long life LED operation
-3-pin XLR IN/OUT
-Master/Slave operation
-RC-1 infrared remote control included
-Control: color range, brightness & rainbow effect with pattern, speed and fadetime control
-LED Colors: Red, Cyan, Green, Magenta, Blue, Yellow, White & Amber
-Power Supply:DC12V, 500mA min included
-Dimensions(LxWxH): 3''x19x2''/76x482x50mm- 1 rack space
Weight: 1.5lbs/ 0.8kg
Notice Information:
*Please Note:
Improvements and specifications in the design of the unit and the manual are subject to change without any prior written notice.
*Special Note:
For reducing signal errors and avoiding signal transmission problems and interference, it is always advisable to connect 120 ohm
impedance DMX signal cable and DMX terminator for signal connection.
Customer Support:
American Audio provides a toll free customer support line, to provide set up help and to answer any question should you encounter
problems during you set up or initial operation. You may also visit us on the web at www.AmericanAudio.us for any comments or
suggestions.
Service Hours are Monday through Friday 9:00 a.m. To 5:30 p.m. Pacific Standard Time.
Voice:(800) 322-6337
Fax:(323) 582-2610
E-mail:support@AmericanAudio.us
-Page 1-
P/N:24-004-2108-00Rev1.1
Operating Instructions:
All work modes and parameters can be set up by a combination with Infrared remote control operation.
1. Before operation, make sure the batteries(3V, CR2025) have been installed properly.
2. Operation Instructions
There are 8 dedicated color brightness pushbuttons(marked Red, Green, Blue, White,
Cyan, Magenta, Yellow, Amber). There are also the "AUTO" and the "UNIT SETTING"
pushbuttons, as well as Raise&Lower keys(marked for "raise" and for "lower")
on the remote unit.
For further information, please refer to the following table;
Pushbuttons&Keys Functions
RED pushbutton
GREEN pushbutton
BLUE pushbutton
CYAN pushbutton
MAGENTA pushbutton
YELLOW pushbutton
WHITE pushbutton
AMBER pushbutton
AUTO pushbutton
PATTERN/RED key
Red, 100% brightness
Green, 100% brightness
Blue, 100% brightness
Cyan, 100% brightness
Magenta, 100% brightness
Yellow, 100% brightness
White, 100% brightness
Amber, 100% brightness
The color is changing automatically, and the brightness is 100%.
To select the next pattern or increase the red brightness, and holding it down,
the brightness will increase continuously until up to the maximum.
Remote Control
PATTERN/RED key
SPEED/GREEN key
SPEED/GREEN key
FADE/BLUE key
FADE/BLUE key
BRIGHTNESS key
BRIGHTNESS key
UNIT SETTING pushbutton
To select the previous pattern or decrease the red brightness, and holding it down,
the brightness will increase continuously until up to the minimum.
To increase the speed or the green brightness, and holding it down, it will
increase continuously until up to the maximum.
To decrease the speed or the green brightness, and holding it down, it will
increase continuously until up to the minimum.
To increase the fade time or the blue brightness, and holding it down, it will
increase continuously until up to the maximum.
To decrease the fade time or the blue brightness, and holding it down, it will
decrease continuously until up to the minimum.
To increase the overall brightness, and holding it down, it will increase
continuously until up to the maximum.
To decrease the overall brightness, and holding it down, it will increase
continuously until up to the minimum.
1. DMX address is set ''1" by default, and with 24 DMX Channels in total.
The Red effect is controlled by Ch1,
The Green effect is controlled by Ch2,
The Blue effect is controlled by Ch3.
2. In Master-Slave operation, one unit will act as the Master unit and the
others will act as the Slave units after Daisy chain your units via the
XLR connector.
3. The Brightness is 100%.
-Page 2-
Loading...