HRV 700SDD/700SFD
HEAT RECOVERY VENTILATOR
PRODUCT
SPECIFICATIONS AND ENGINEERING
INFORMATION
-----
SUBMITTAL DATA
|
|
496 - 4-03 |
ALDES Model HRV 700SFD or |
ALDES HRV 700SDD and |
|
700SDD is a compact heat recov- |
||
stale indoor air and supply fresh air |
700SFD |
|
ery ventilator designed to exhaust |
|
|
from outdoors. It is intended for |
Heat Recovery Ventilator |
|
small commercial and institutional |
|
|
applications, such as office build- |
|
|
ings, classrooms, dormitories, res- |
|
|
taurants, health clubs, etc. |
|
|
It is a technically advanced con- |
|
|
trolled mechanical ventilation sys- |
|
|
tem to meet the requirements of |
|
Optional Damper Defrost |
modern, tightly built and highly in- |
|
on Model 700 SDD |
|
|
|
sulated buildings. It provides a |
|
|
consistent supply of fresh air while |
|
PART NO. 700SFD / 28 105 |
lowering heating costs during the |
|
700SDD / 28 106 |
|
|
|
winter by transferring heat from the |
|
|
exhaust air to the fresh air stream. |
The Model 700 is available with two |
temperatures rise above 23 °F. |
During the summer it also reduces |
defrost options. The Model 700SFD |
The Model 700SDD blocks out- |
the load on the air conditioner by |
begins the defrost cycle at tempera- |
side air during defrost and draws |
lowering the temperature of the |
tures below 23 °F (-5 °C) by shutting |
indoor air through the supply (with |
fresh outdoor air. The system pro- |
off the supply fan for 4-1/2 minutes, |
the same temperature and defrost |
vides an economical solution for |
then resumes normal operation for |
time schedule as the fan defrost |
excessive indoor humidity, odors, |
17 minutes, repeating the cycle until |
system). |
stuffiness, and other indoor air pol- |
|
|
lutants. |
GENERAL FEATURES |
|
|
||
As the two air streams pass through |
Thermally conductive aluminum heat exchange core, cross- |
|
the HRV, they are separated by thin |
flow design, easily removed for cleaning or service. |
|
plates of aluminum in the core. The |
Insulated 20 gauge powder coated galvanized steel cabinet. |
|
air streams do not mix, so there is |
Direct drive centrifugal forward curve blowers, Multi-speed |
|
no recontamination of the fresh air |
providing 400 to 650 cfm. one in each air stream. |
|
Two efficient three speed PSC double shafted motors 120 V, |
||
by stale air. Heat passes through |
||
the thermally conductive aluminum |
2.75 Amps each (5.5 Amps total on high speed), |
|
1 ph. 1/10 HP, 1625 RPM. Watts - total on high speed - 648. |
||
from the warmer air stream to the |
||
Washable filters, one in each air stream protect the core. Easy |
||
colder air stream, recovering most |
||
to access and clean. |
||
of the energy otherwise lost to the |
Installation accessories and controls make installation simple. |
|
outdoors. |
|
PERFORMANCE
OPTIONS AND ACCESSORIES 28 998: 60 MIN. REMOTE TIMER (2 Wire)
28 882 DEHUMIDISTAT - Activates high speed when indoor humidity rises above set point on control (2 Wire)
Note: Manufacturer |
WARRANTY |
reserves the right to change |
Units carry a 15 year warranty on |
specifications without notice. |
the heat recovery core and a 2 |
year replacement parts warranty. |
All units conform to CSA and UL Standards
SPECIFICATIONS
General: Unit shall be completely wired and includes blowers, filters, heat exchange cores and control panel.
Cabinet: 29 5/8” x 28 3/4” x by 24 5/8” H. Constructed of 20 gauge satin white powder coated galvanized steel (G60) for superior corrosion resistance. Insulated with foil faced fiberglass duct liner to prevent condensation.
Heat Exchange Core: Two modules, aluminum plate heat exchange core assembly held in stainless steel frame.
Air filter: Four washable filters.
Motors: Two efficient three speed PSC double shafted motors 120V, 2.75 Amps each (5.5 Amps total on high speed), 1 ph.
1/10 HP, 1625 RPM. Watts - total on high speed - 648.
Blowers: Centrifugal type rated at 700 CFM (329 L/s) free air delivery. Each air stream has one double shafted motor driving a centrifugal blower. Rubber isolated mounts.
Controls: Illuminated power switch, 3 speed blower control, low voltage (24 VAC) terminals for connection of remote controls and defrost light indicating automatic operation.
Defrost: Model 700SDD: Supply bypass routes indoor air to defrost core.
Model 700SFD: Supply fan shuts off while exhaust continues to defrost core. (Defrost light indicates defrost modePreset 27° F (-3°C)).
Duct Connections: Four 14" X 8" (356mm X 200mm). Model 700SDD has fifth 14" x 8" duct connection on top surface.
Drain Connections: Two 1/2" O.D.
Mounting: Unit to be set in support brackets hung by threaded rod type apparatus. (Brackets and rod not provided).
Weight: 142 lbs (64.4 Kg)
Shipping Weight: 167 lbs (75.8 Kg)
Manufacturer: American ALDES Ventilation Corp.
4537 Northgate Court, Sarasota, FL 34234
DIMENSIONS 700SDD / 700SFD
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROJECT |
|
DATE |
|
SUBMITTED BY |
|
CONTRACTOR |
|
|
|
|||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4537 NORTHGATE COURT SARASOTA, FL 34234-2124, USA Tel: 941 • 3513441
Fax: 941 • 3513442 www.aldes-us.com e-mail: info@aldes-us.com
BY MATHEWS GRAPHIC DESIGN
496HRV4-03
HRV 700SDD/700SFD PLUS
HEAT RECOVERY VENTILATOR
PRODUCT
SPECIFICATIIONS AND ENGINEERING INFORMATION
SPECIFICATIONS
CORES - Modular (2 section) patented aluminum heat recovery cores arranged for efficient cross-flow ventilation.
MOTORS - Two PSC, 3 speed single shafted, 120 VAC, 4.5 Amps each (9 total on high speed). HP - 1/4, 1450 RPM. Watts - total on high speed - 1032.
FILTERS - Washable air filters in exhaust and supply air streams.
BLOWERS - Centrifugal type rated at 329 L/s (700 CFM) free air delivery. Each air stream has one single shafted motor driving a centrifugal blower.
CONNECTION DUCT SIZES - Four - 14” x 8” (356 mm x 200 mm). MOUNTING - Unit to be set on support brackets hung by threaded rod type apparatus (brackets and rods not provided). CASE - 20 gauge prepainted galvanized steel (G60) for superior corrosion resistance. Insulated with foil faced insulation where required to prevent exterior condensation. Drain connections, 2 - 1/2” (12 mm) O.D.
CONTROLS & FUNCTION - Integrated microprocessor circuit board. Built-in interlock contacts. Automatic Self Test. Optional remote speed control.
DEFROST CONTROLS
Model 700SFD PLUS - Interrupts supply air while exhaust air defrosts core.
Model 700SDD PLUS - Supply bypass routes indoor air to defrost core.
WEIGHT - 155 lbs. (70 kg) SHIPPING WEIGHT - 180 lbs. (81.4 kg)
HIGH SPEED MED. SPEED
LOW SPEED
DIMENSIONS 700SFD/700SDD PLUS inches (mm)
OPTIONS
28 998 Sixty Minute Timer (2 Wire)
28 883 Dehumidistat Ventilation Control (DVC) Remote dehumidistat and on/off control (3 Wire)
28 882 Dehumidistat Control - Remote Wall Mount, Low Voltage 20-80% RH (2 Wire)
28 885 3 Speed Control (4 Wire)
All units conform to CSA and UL standards.
WARRANTY
Units carry a 15 year warranty on the heat recovery core and a 2 year replacement parts warranty.
6
HRV P700SDD
HEAT RECOVERY VENTILATOR
POOL MODEL
PRODUCT
SPECIFICATIONS
AND ENGINEERING
INFORMATION
-----
SUBMITTAL DATA 497HRV70-4-03
ALDES Pool Model Heat Recover Ventilators are designed to exhaust humid air from indoor swimming pools and spa area and to supply tempered fresh air from outdoors. It incorporates an efficient aluminum core for heat recovery of waste heat to temper the fresh outdoor air, to provide and economical solution to excessive humidity, odor, stuffiness, and other indoor air pollutants. The model P700SDD is intended for small commercial, institutional, and residential applications for pool and wetted deck areas up to 700 square feet.
The pool model has three modes of operation to meet the unique needs of pools. The normal ventilation mode provides exhaust of humid air and supply of fresh outdoor air, with heat recovery in the efficient aluminum cores. This mode is controlled by an adjustable dehumidistat that opens the fresh air damper to the outdoor air intake, and operates both the supply and exhaust fans. (A duct heater or hot water coil may be installed in the supply duct to provide additional heat to the incoming air or recirculating air. This heater would be controlled by a duct mounted thermostat.)
The second mode of operation occurs when the humidity level falls below the setpoint of the dehumidistat. The exhaust fan shuts off, the supply air damper closes off outdoor air, and opens
ALDES HRV P700SDD |
Heat Recovery Ventilator |
for Swimming Pools |
Standard Damper |
Defrost |
PART NO. 28 110 |
the recirculation air circuit. This mode maintains constant air circulation in the conditioned space, and a means of heating the conditioned space if a duct heater or hot water coil is installed in the supply duct.
The third mode of operation provides automatic defrost by shutting off fresh air intake in a cycle of 4.5 minutes off, 17 minutes on. The defrost cycle occurs when outdoor temperatures are below 27°F (-3°C)
GENERAL FEATURES
Thermally conductive aluminum heat exchange core, crossflow design, easily removed for cleaning or service.
Insulated 20 gauge white powder coated galvanized steel cabinet.
Direct drive centrifugal forward curve blowers, Multi-speed providing 400 to 650 cfm. one in each air stream.
Two efficient three speed PSC double shafted motors 120 V, 2.75 Amps each (5.5 Amps total on high speed),
1 ph. 1/10 HP, 1625 RPM. Watts - total on high speed - 648
Washable filters, one in each air stream protect the core. Easy to access and clean.
Installation accessories and controls make installation simple.
PERFORMANCE
OPTIONS AND ACCESSORIES 28 998: 60 MIN. REMOTE TIMER
28 882 DEHUMIDISTAT - Activates high speed when indoor humidity rises above set point on control
Note: Manufacturer |
WARRANTY |
|
|
reserves the right to change |
Units carry a 15 year warranty on |
||
specifications without notice. |
the heat recovery core and a 2 |
||
year replacement parts warranty. |
|||
|
|||
All units conform to CSA and UL Standards
SPECIFICATIONS
General: Unit shall be completely wired and includes blowers, filters, heat exchange cores and control panel.
Cabinet: 29 5/8” x 283/4” x by 245/8” H (753 x 730 x 625 mmH). Constructed of 20 gauge prepainted galvanized steel (G60). Interior lined with foil faced Insulation where surface is exposed to cold air. Access door is hinged and latch. Disconnect switch engaged by door panel. Condensate pan has drain connections.
Heat Exchange Core: Two modules, aluminum plate heat exchange core assembly.
Air filter: Four washable filters.
Motors: Two efficient three speed PSC double shafted motors 120 VAC, 2.75 Amps each (5.5 Amps total on high speed), 1/10 HP, 1625 RPM. Watts - total on high speed - 648.
Blowers: Centrifugal type rated at 700 CFM (329 L/s) free air delivery. Each air stream has one double shafted motor driving a centrifugal blower. Rubber isolated mounts.
Controls: Illuminated power switch, 3 speed blower control, low voltage (24 VAC) terminals for connection of remote controls and defrost light indicating automatic operation.
Defrost: Pool and Defrost air bypass routes air to defrost core. Light indicates when automatic damper defrost occurs (preset at 27°F (-3°C).
Duct Connections: Five 14" X 8" (356mm X 200mm H).
Drain Connections: Two 1/2" O.D.
Mounting: Unit to be set in support brackets hung by threaded rod type apparatus. (Brackets and rod not provided).
Weight: 142 lbs (64.4 kg)
Shipping Weight: 167 lbs (75.8 kg)
Manufacturer: American ALDES Ventilation Corp.
4537 Northgate Court, Sarasota, FL 34234
DIMENSIONS
P700SDD
|
|
|
|
|
BY MATHEWS GRAPHIC DESIGN |
PROJECT |
DATE |
SUBMITTED BY |
CONTRACTOR |
||
|
|
|
|
|
VENTILATION |
4537 NORTHGATE COURT |
|
|
|
||
SARASOTA, FL 34234-2124, USA |
|
|
|
||
Tel: |
941 |
• 3513441 |
|
|
|
Fax: |
941 |
• 3513442 |
|
|
497HVP70.4-3 |
www.americanaldes.com |
|
|
|||
e-mail: info@aldes-us.com
HRV850DFD/850DDD
HEATRECOVERYVENTILATOR
PRODUCT
SPECIFICATIONS
AND ENGINEERING
INFORMATION
-----
SUBMITTAL DATA
|
|
378-850-4-03 |
|
ALDES Model HRV 850DFD, |
ALDES HRV 850DFD and |
||
ery ventilator designed to exhaust |
|||
850DDD is a compact heat recov- |
850DDD |
||
from outdoors. |
It is intended for |
||
stale indoor air and supply fresh air |
Heat Recovery Ventilator |
||
applications, such as office build- |
|||
small commercial and institutional |
|
||
ings, classrooms, dormitories, res- |
PART NO: 850 DFD / 28 107 |
||
taurants, health clubs, etc. |
850 DDD / 28 108 |
||
It is a technically advanced con- |
|
||
trolled mechanical ventilation sys- |
|
||
tem designed to meet the require- |
|
||
ments of modern, tightly built and |
|
||
highly insulated buildings. It pro- |
|
||
vides a consistent supply of fresh |
|
||
air while lowering heating costs |
|
||
during the winter by transferring |
|
||
heat from the exhaust air to the |
|
||
fresh air stream. During the sum- |
|
||
mer it also reduces the load on the |
|
||
air conditioner by lowering the tem- |
|
||
perature of the fresh outdoor air. |
|
||
(For southern climates, where air |
|
||
conditioning costs are the major |
|
||
concern, it can be provided with an |
|
||
enthalpy core, on special order, to |
|
||
reduce the humidity of the fresh air |
|
||
as well as lower the temperature.) |
|
||
The system provides an economi- |
|
||
cal solution for excessive indoor |
|
||
humidity, odors, |
stuffiness, and |
|
|
other indoor air pollutants. |
|
||
As the two air streams pass through |
|
||
the HRV, they are separated by thin |
GENERAL FEATURES |
||
plates of aluminum in the core. The |
|||
Thermally conductive aluminum heat exchange core, cross-flow design, |
|||
air streams do not mix, so there is |
|||
no recontamination of the fresh air |
easily removed for cleaning or service. |
||
by stale air. Heat passes through |
Two efficient three speed PSC motors drive dual centrifugal blowers. 120 |
||
the thermally conductive aluminum |
V. 3.95 Amps each (7.9 Amps total on high speed), 1/4 HP, 1625 RPM, 848 |
||
from the warmer air stream to the |
Watts (total) on high speed |
||
colder air stream, recovering most |
Washable filters on each air stream protect the core. Easy to access and |
||
of the energy otherwise lost to the |
|||
clean. |
|||
outdoors. |
|
||
|
Defrost: Model 850DFD Interrupts supply air while exhaust air defrosts |
||
|
|
||
Equally important to providing air |
core. |
||
Model 850DDD Recirculating defrost. Internal damper closes |
|||
change from outdoors to indoors is |
|||
fresh air intake and draws indoor air through heat exchange |
|||
a means of distributing the fresh air |
|||
cores. |
|||
to all parts of the building, through a |
|||
Both models: Defrost light indicates when defrost cycle operates |
|||
ducting system. Often, the ducting |
|||
(at temperatures below 27 °F (-3 °C). |
|||
of a central forced air system can |
Installation accessories and controls make installation simple. |
||
be used. |
|
||
|
|
||
Loading...