Page 1
FULLY RECESSED ELECTRIC FIREPLACE
Model#: BEF-50BIF03 (Linear 50)
OWNER’S MANUAL
BEF-72BIF03 (Linear72)
WARNING
CAUTION
Rev_1
50”/ 72” - Built-in Electric Fireplace
AC 220-240V 50Hz 1400-1600W
Read and understand this entire owner’s manual, including all safety
information, before plugging in or using this product. Failure to do so could
result in fire, electric shock, or serious personal injury.
Keep this owner’s manual for future reference. If you sell or give this
product away, make sure this manual accompanies this product.
Page 2
IMPORTANT SAFETY INFORMATION!
WARNING
When using electrical appliances basic precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
Read all instructions before using this heater.
This heater is hot when in use. To avoid burning, do not touch hot surface. If provided, use
handles when moving this heater. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least 1 m from the front of the heater and keep them
away from the sides and rear. In order to avoid overheating, do not cover the heater.
Extreme caution is necessary when any heater is used near children or the infirm and
whenever the heater is left operating and unattended.
Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has
been dropped damaged in any manner, return heater to authorized service facility for
examination, electrical or mechanical adjustment, or repair.
Indoor use only, do not use outdoors.
This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
Never locate heater where it may fall into a bathtub or other water container.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. Arrange cord away from traffic area and where it will not be tipped over.
To disconnect heater, turn controls to off, then remove plug from outlet.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock or fire, or damage the heater.
To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.
A heater has hot surfaces and arcing or sparking parts inside. Do not use it in areas where
gasoline, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons.
DANGER-HIGH Temperatures may be generated under certain abnormal conditions. Do not
partially or fully cover or obstruct the front of this heater.
Replacement of the LEDs should only be done by a qualified technician or service agency while
the heater is disconnected from the supply circuit.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they do not play with the appliance.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by the utility.
Do not use outdoors.
Do not use in immediate surroundings of water, bath, shower, or pool etc.
Page 3
Preparation
This product includes a GLASS panel! Always use extreme caution when handling
glass. Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts
and assembly steps are grouped for free-standing or wall-hanging use. Check the parts list to make
sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.
You will need the following tools (not included): Phillips screwdriver; stud finder; level; tape
measure; electric drill; 1/4” wood drill bit, hammer.
Parts and Hardware
A – Fireplace
F – Decorative Clear Crystals
(Big & Small)
B – Wood Screws
D - Decorative Pebbles
RC - Remote Control
C – Drywall Anchors
E – Decorative Black Crystals
Page 4
Installation and Assembly
Front View of Fireplace
Minimum
clearance to
flooring: 30 cm
Step 1. Find a safe location.
Minimum clearance
Choose a location near an outlet so
an extension cord is not required.
DO NOT position the unit directly
below a power outlet.
See Safety Information on pages 2
and 3 for warnings about safe
placement, safe installation, and
proper use of this product.
to flooring: 30 cm
ALWAYS unplug this fireplace before assembly or cleaning, or before relocating.
Failure to do so could result in electric shock, fire, or personal injury.
Page 5
Installation
Model No. W H
T
BEF- 50BIF03
BEF- 72BIF03
STEP 1. Select a dry wall to open a hole for fireplace box. Size of cavity as below chart
1215mm 432mm 170mm
1775mm 432mm 170mm
Figure ( A )
Page 6
Figure ( B )
STEP 2. Place the fireplace in a clean dry place. Use the screw driver to take off the TWO
screws in both sides. Figure (B)
Figure ( C )
Page 7
STEP 3. Have two people pull the trim up, and then take them out of the fireplace box. Figure (C)
Figure ( D )
STEP 4. Use the screw driver to take off the 8 screws as above Figure (D). Have two people take out
the glass panel Figure (E) and move it to a clean area taking care to avoid scratching.
Figure ( E )
Page 8
STEP 5. Have two people lift the fireplace box and put it into the hole. Fix the FOUR wall screws in
each side of the fireplace box. Figure (F)
Figure ( F )
STEP 6. Place the Decorative Crystals and Drift Log pieces on the designed slot and keep them even.
Figure (G)
Figure ( G )
STEP 7. After placing the Decorative Crystals or Pebbles on the designed slot, fasten screws back on
the glass panel and metal trim.
(Repeat as Fig B,C,D,E)
Page 9
Operation
Read and understand this entire owner’s manual, including all safety information,
before plugging in or using this product. Failure to do so could result in electric shock,
fire, serious injury, or death.
Power
Plug the power cord into an outlet or hard wire the appliance. If you choose to hard wire the appliance,
it MUST have a dedicated isolation switch accessible after installation.
Warning: do not attempt to wire your own new outlets or circuits. Always use a licensed electrician.
Methods of Operation
This electric fireplace can be operated by the TOUCH PANEL, located on the right side panel of the
fireplace (see figure below), or by the battery-powered REMOTE CONTROL.
The operation and functions of the two methods are the same.
Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3,
and heed all warnings.
Touch Panel
Page 10
Remote Control &Touch Panel Operation
BUTTON FUNCTION ACTION & INDICATION
POWER
TIMER
FLAME
ON: Enables control panel functions and
remote control. Turns on flame effect.
OFF: Disables control panel functions and
remote control. Turns off flame effect.
TIMER button: Controls timer settings to
turn off fireplace at selected time.
Settings range from 0.5 hours to 8 hours.
FLAME button: Makes flame effect
dimmer and brighter.
NOTE: Flame effect stays on until power
button is turned off. Flame effect must be
on for heater to turn on.
COLOR button: Changes the color of
the flame effect.
1.
Press once. Indicator light turns on.
Power turns on. All functions
enabled.
2.
Press again. Flame effect turns off. Unit
goes to standby. All functions turn off.
1.
Press once. Indicator light turns on.
Timer is set to 0.5 hours.
2.
Press again until desired setting is
reached. Indicator lights show setting.
1.
Press once. Flame brightness effect
gets changing.
2.
Press again. until desired setting is
reached.
1.
Press once. Flame color changes.
COLOR
HEATER
NOTE: color effect stays on until power
button is turned off. Color flame effect
must be on for heater to turn on.
NOTE: The fireplace will remember
color selection.
HEATER button: Turns heater on and off.
NOTE: The heater only works when the
flame effect is on. If the flame effect is off,
the heater will not turn on.
NOTE: To prevent overheating, the heater
fan will blow cool air for 8-10 seconds
before the heater turns on, and after the
heater turns off.
2.
Press again until des
reached.
1.
Press once. Indicator lights up.
Fan blows cool air for 10 seconds. 750W
heater turns on and blows warm air.
2.
Press again. Indicator lights up.
1500W heater turns on and blows hot air.
3.
Press again. Heaters turn off.
The fan blows cool air for 10 seconds to
allow heater to cool down, then turns off.
ired setting is
Page 11
TEMPERATURE button: Turns heater
When the fireplace is first turned on, a slight odor may be present. This is normal
eriod of
on and off.
NOTE: Press the button for 5 seconds, the
temperature setting will switch from ℃ to
℉. Same way from ℉ to ℃。
1.
Press once: Touch panel indicator
becomes active.
2.
Press again: until desired setting is
‘ Reached. Digital display shows
setting circles as below:
LED Ember light button ( 1 ): Changes
the color of the bottom (ember) lighting.
NOTE: Ember color effect stays on until
power button is turned off.
LED Bottom light button ( 2 ): Makes the
color on bottom (ember) lighting effect
automatically cycle (flash) through color
options.
NOTE: Ember color effect stays on until
power button is turned off.
NOTICE
NOTICE
1.
Press once. Ember color effect is
changed.
2.
Press again. until desired setting is
reached, in total a cycle of 10 colors.
1.
Press once. Ember color effect is
changed automatically.
2.
Press again. Ember color effect
flashes and is changed automatically.
and should not occur again unless the fireplace is not used for a long p
time.
To improve operation, aim the remote control at the front of the fireplace. DO NOT
press the buttons too quickly. Give the unit time to respond to each command.
Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe
temperature, the heater will automatically turn OFF. To reset:
1.
Unplug the power cord from the outlet.
2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.
3.
Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are,
use a vacuum to clean the vent areas.
4.
With the POWER switch in the OFF position, plug the power cord back into theoutlet.
5. If the problem continues, have your outlet and wiring inspected by a professional.
Remote Control Battery Information
•
This remote control uses CR2025 battery (included).
•
Instructions for battery installation are on the Remote Control batterycompartment.
NEVER dispose of batteries in fire. Failure to observe this precaution may result in an
explosion. Dispose of batteries at your local hazardous material processingcenter.
Page 12
Care and Maintenance
serviceable parts
before
cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in
electric shock, fire, or personal injury
before
moving this fireplace. Failure to do so could result in
electric shock,
Cleaning
ALWAYS turn the fireplace OFF and unplug the power cord from the outlet
cleaning, performing maintenance, or
electric shock, fire, or personal injury.
NEVER immerse in water or spray with water. Doing so could result in
fire, or personal injury.
Metal:
•
Buff using a soft cloth, slightly dampened with a citrus oil-based product.
•
DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Glass:
•
Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper
towel or lint-free cloth.
•
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch thesurface.
Vents:
•
Use a vacuum or duster to remove dust and dirt from the fireplace and ventareas.
Plastic:
•
Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
•
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch thesurface.
Main
Electrical and Moving Parts:
Storage:
tenance
Risk of electric shock! DO NOT OPEN any panels ! No userinside!
ALWAYS turn the fireplace OFF and unplug the power cord from the outlet
•
The fan motors are lubricated at the factory and will not requirelubrication.
•
Electrical components are integrated in the fireplace and are not serviceable by the consumer.
•
Store fireplace in a clean dry place when not in use.
WARNING! NO SERVICING of the internal or electrical parts should be performed by the
consumer. Do not service the unit yourself.
.
Page 13
Troubleshooting
! WARNING
DISCONNECT THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. ONLY A
QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
Problem
1.
Fireplace turns off 1. Fireplace has overheated
and will not turn on.
2.
Flame is not moving. 1. Loose wiring.
3.
Flame is not visible. 1. Wiring is loose.
4.
Log set and/or
ember is not
glowing.
5.
Remote control
does not work.
6.
Fireplace will not
come on when
switch is flipped to
ON.
Possible Cause Solution
and safety device has caused
thermal switch to disconnect
or home circuit breaker has
opened.
2. Flame motor defective.
3. Flame rod out of place.
1.Wiring is loose.
2.Ember is in off mode.
1.
Low batteries.
2.
Not aiming control correctly.
3.
Defective remote control and
/or sensor.
1.
Fireplace is not plugged in to
an electrical outlet.
2.
Control failure.
3.
Breaker tripped.
1. Reset switch by turning main
power switch off and waiting 10
minutes then turning it back on
or reset circuit breaker.
1.
Inspect wiring for loose con-
nections.
2.
Call a qualified service techni-
cian to replace flame motor.
3."Flame Rod" out of place due to
rough transit/handling of
product. This issue
corrected as simple as removing
the glass, flipping the fireplace
upside down, removing a set of
screws that are
bottom frame plate and placing
the flame rod back into place.
1. Disconnect from power source
and inspect wiring for loose
connections and repair or
replace if
2. Push the flame button to high.
1.
Disconnect from power source
and inspect wiring for loose
connections and repair or replace
if necessary.
2.
Ensure the ember button is
pressed until on high.
1.
remote control.
2.
Aim control at sensor located
directly behind glass screen in
center of unit just above logs.
3.
Replace remote control and/or
sensor.
1.
Check plug.
2.
Call a qualified service techni-
cian.
3.
Reset breaker.
necessary.
Replace batteries in
holding
the
can be
the
Page 14
7.
Heater does not
provide heat when
turned on.
1.
Thermal switch has been
tripped.
2.
Wiring is loose.
3.
Heater is defective.
1.
Turn unit off and unplug unit
for 10 minutes. Plug back in and
turn unit on. If plug cannot be
reached, follow directions for
tripped circuit breaker.
2.
Disconnect from power source
and inspect wiring for loose
connections and repair or
replace if necessary.
3.
Replace heater.
Touch panel /
8.
Remote Control do
not work.
The front glass is moved or
not secured properly.
Unplug the appliance, if the appliance is
recessed to the wall, shut off house circuit
breaker. Ensure the front glass is in the
correct location and is sitting flat to the
appliance touch panel. after 15 seconds,
plug or turn on the appliance to reset it.
CAUTION:To remove the glass, you will notice two screws on front both sides (right and left) of the
fireplace. Once the screws are removed, slide the glass up and away from the fireplace. Once the
bottom frame plate is removed, you will notice one flame motor on right side where the rod should be
in place with the rubber plugs.
Please remember to always have the unit disconnected prior to any work, always lay glass as well
as the unit on a towel or other material not to damage parts/frame.
This entire process should not take longer than 20-30 minutes.
Loading...