Amana NGD4700YQ, NGD4500VQ Dimension Guide

29" and 27" Dryers

3"*

Gas (U.S.A. and Canada)

PRODUCT MODEL NUMBERS

NGD4500V, NGD4600Y, NGD4700Y, NGD5100T

Installation clearances:

The location must be large enough to allow the dryer door to open fully.

Most installations require a minimum 5½" (140 mm) clearance behind the dryer for the exhaust vent with elbow.

29" Wide Models Dryer Dimensions

27" Wide Models Dryer Dimensions

43"

(1092 mm)

23¾"

(603 mm)

43"

(1092 mm)

13¾"

(349 mm)

A. Large opening side-swing door B. Large opening side-swing door C. Wide opening side-swing door D. Wide opening hamper door

Installation Spacing

18"* (457 mm)

1" (25 mm)

29"

(737 mm)

1" (25 mm)

A. Recessed area B. Side view – closet or conned area C. Closet door with vents

1"* (25 mm)

14" max.* (356 mm)

27¾"

(705 mm)

48 in. (310 cm )

24 in.

(155 cm )

*291/2"

(749 mm)

(687 mm)

27"

*291/2"

(749 mm)

(687 mm)

27"

A. Large opening side-swing door B. Large opening side-swing door

Installation Spacing

14" max.* (356 mm)

18"*

48 in.

(310 cm )

(457 mm)

24 in.

(155 cm )

1" (25 mm)

27"

(686 mm)

1"*

(25 mm)

¼"

(743 mm)

5½"*

(140 mm)

A. Recessed area B. Side view – closet or conned area C. Closet door with vents

3"* (76 mm)

Installation spacing for recessed area or closet

The dimensions shown are for the minimum spacing allowed.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door, and

oor moldings.

3"* (76 mm)

■ Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

■ Companion appliance spacing should also be considered.

(76 mm)

3"*

(76 mm)

*Required spacing

W10115228C

02/2012

INSTALLATION REQUIREMENTS

GAS SUPPLY REQUIREMENTS

Gas supply: This dryer is equipped for use with Natural gas. Dryer can be converted to L.P. gas. When rigid pipe is used it should be 1/2" IPS. When acceptable to the gas supplier and local codes, 3/8" approved tubing may be used for lengths under 20 ft (6.1 m). For lengths over 20 ft (6.1 m), larger tubing should be used. Pipe-joint compounds resistant to the action of L.P. gas must be used. An individual manual shutoff valve must be installed within 6 ft (1.8 m) of the dryer in accordance with the National Fuel Gas Code ANSI Z223.1.

ELECTRICAL REQUIREMENTS

A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required. A time-delay fuse or circuit breaker and a separate circuit are recommended.

VENTING REQUIREMENTS

Exhaust venting: Exhaust your dryer to the outside. 4" (102 mm) diameter vent is required. Rigid or exible metal exhaust vent must be used. Do not use plastic or metal foil vet. Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust.

Exhaust hoods:

Recommended Styles:

Louvered Hood

Box Hood

Acceptable Style:

Angled Hood

Determine vent path:

■ Select route that will provide straightest and most direct

path outdoors.

■ Plan installation to use fewest number of elbows and turns.

■ When using elbows or making turns, allow as much room

as possible.

■ Bend vent gradually to avoid kinking.

■ Use as few 90° turns as possible.

Determine vent length and elbows needed for best drying performance:

■ Use following Vent System Chart to determine type of vent

material and hood combinations acceptable to use.

The “Vent System Chart” provides venting requirements that will help achieve best drying performance.

Vent System Chart

Number of 90° turns or elbows

NOTE: Side and bottom exhaust installations for 27" wide

models have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart.

Type

of vent

Rigid metal

Box/louvered

hoods

64 ft. (20 m)

54 ft. (16.5 m)

44 ft. (13.4 m)

35 ft. (10.7 m)

27 ft. (8.2 m)

Angled

hoods

58 ft. (17.7 m)

48 ft. (14.6 m)

38 ft. (11.6 m)

29 ft. (8.8 m)

21 ft. (6.4 m)

Vent System Chart

(29" Wide Long Vent Models Only)

Number of

90° turns

or elbows

0 Rigid metal 120 ft. (36.6 m)

Type

of vent

Rigid metal

Box/louvered, or

Angled hoods

110 ft. (33.5 m)

100 ft. (30.5 m)

NOTE: Do not use vent runs longer than those specied in Vent System Chart. Exhaust systems longer than those specied will:

■ Shorten life of dryer.

■ Reduce performance, resulting in longer drying times

and increased energy usage.

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.

Rigid metal

90 ft. (27.4 m)

80 ft. (24.4 m)

70 ft. (21.3 m)Rigid metal