Amana AGR5330BA Dimension Guide

30"(76.2 cm) Freestanding Gas Ranges

PRODUCT MODEL NUMBERS

AGR5330BA

ELECTRICAL REQUIREMENTS

A 120-volt, 60 Hz., AC-only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided.

GAS REQUIREMENTS

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 latest edition or CAN/CGA B149 - latest edition.

IMPORTANT: Leak testing of the range must be conducted according to the manufacturer’s instructions. See “Complete Connection” in the “Make Gas Connection” section.

Type of Gas

Natural gas:

■ This range is factory set for use with Natural gas. The model/serial

rating plate located on the left side of the bottom of the broiler has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualiﬁed service technician. No attempt shall be made to convert the appliance from the gas speciﬁed on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See “Gas Conversions” section.

Gas Supply Line

■ Provide a gas supply line of

location. A smaller size pipe on longer runs may result in insufﬁcient gas supply. With LP gas, piping or tubing size can be 1/2" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape.

Flexible metal appliance connector:

■ If local codes permit, a new CSA design-certiﬁed, 4 to 5 ft (122

to 152.4 cm) long, 1/2" (1.3 cm) or 3/4" (1.9 cm) I.D., ﬂexible metal appliance connector may be used for connecting range to the gas supply line.

/4" (1.9 cm) rigid pipe to the range

PRODUCT DIMENSIONS

A. 36" (91.4 cm) B. 297⁄8" (75.9 cm) C. 257⁄64" (63.8 cm) D. 475⁄64" (119.6 cm)

■ A

/2" (1.3 cm) male pipe thread is needed for connection to the

female pipe threads of the inlet to the appliance pressure regulator.

■ Do not kink or damage the ﬂexible metal tubing when moving the

range.

■ Must include a shut-off valve:

The supply line must be equipped with a manual shut-off valve. This valve should be located in the same room but external to the range opening, such as an adjacent cabinet. It should be in a location that allows ease of opening and closing. Do not block access to shut-off valve. The valve is for turning on or shutting off gas to the range.

A. Gas supply line B. Shut-off valve “open” position C. To range

Page 1 of 2

Because Whirlpool Corporation includes a continuous commitment to improve our products, we reserve the right to change materials and speciﬁcations without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Speciﬁcations subject to change without notice.

Ref. W10860789A

12/19/16

CABINET DIMENSIONS

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth, and 36" (91.4 cm) countertop height.

If the cabinet depth is greater than 24" (61.0 cm), oven frame must extend beyond cabinet fronts by 1/2" (1.3 cm) minimum.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

A. 18" (45.7 cm) min. clearance upper side cabinet to countertop B. 13" (33.0 cm) max. upper cabinet depth C. 30" (76.2 cm) min. cabinet opening width D. For minimum clearance to top of cooktop, see NOTE*. E. 301⁄8" (76.5 cm) min. opening width F. This shaded area recommended for installation of electrical outlet. G. This shaded area recommended for installation of rigid gas pipe. H. 2" (5.1 cm) min. countertop space to side wall or other combustible

material I. 24" (61.0 cm) J. 10" (25.4 cm) K. 8" (20.3 cm) L. 5" (12.7 cm) M. 2" (5.1 cm) N. 3" (7.6 cm)

* NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet

is covered by not less than 1/4" (0.64 cm) ﬂame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum, or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking

platform and the bottom of an uncovered wood or metal cabinet.

Because Whirlpool Corporation includes a continuous commitment to improve our products, we reserve the right to change materials and speciﬁcations without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Speciﬁcations subject to change without notice.

Page 2 of 2

Ref. W10860789A

12/19/16