Altronix PACE1PRMT, PACE1PTM User Manual

Installation Guide
Rev. 111413
Pace1PRMT - IP and PoE+ over extended
Z1409
distance UTP or CAT5e
Pace1PRM Receiver and Pace1PTM Transceiver kit
Overview:
Pace1PRMT is a long range Ethernet adapter kit which transmits data at 100mbps full duplex and power via a single twisted pair (UTP) or Cat5e or higher cable in a PoE(+) compliant format. The Pace1PRM receiver is powered via a PoE midspan such as the Altronix Netway series or by an endspan. The receiver passes the PoE(+) compliant power over the cable to the Pace1PTM transceiver which in turn passes this power to an enabled IP camera/device. These plug and play units facilitate cost effective solutions for IP devices that need to be installed at distances greater than 100m. They also provide a simple way to replace legacy analog products with new IP devices over single twisted pair (UTP) or structured cable.
Agency Listings:
• UL/CUL Listed for Information Technology Equipment (UL 60950-1).
• CE approved.
• C-Tick compliant.
Input (Pace1PRM):
• Powered by midspan or endspan. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W).
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 or 1 pair UTP structured cable.
• Distance: up to 457m (1,500 ft.).
• Speed: 10/100BaseT, half/full duplex, auto negotiation. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W) delivered to camera by Pace1PTM. Power provided by Pace1PRM to Pace1PTM by PoE protocol.*
• Throughput is rated to pass 100mbps of data at distances up to 1,500 ft. With proper headend equipment, this supports Megapixel, HD720, HD1080.
CAT5e or higher:
• Distance: up to 1,500 ft. @ 100mbps (see Maximum Length of CAT5e Type vs. Camera Power/PoE Class, pg. 4).
UTP (single pair):
• Distance: up to 1,000 ft. @ 100mbps, up to 1,500 ft. @ 10mbps (see Max. Length of UTP Type vs. Camera Power/PoE Class, pg. 4).
LED Indicators:
• Pace1PRM/Pace1PTM: Green - PoE ON (by respective RJ45 jack).
• Pace1PRM and Pace1PTM (RJ45 jack): Yellow and Green LED IP Link status, 10/100Base-T/active.
Environmental:
Operating Temperature Pace1PRM/ Pace1PTM:
-- 4ºF to 120.2ºF (-- 20ºC to +49ºC).
Storage Temperature:
-- 22º to 158ºF (-- 30º to +70ºC) Storage.
• Humidity: 20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy non-PoE cameras/devices.
Applications:
• Extend Network link distance in an industrial environment over 610m (2000 ft.) (see note, pg. 2).
• Retrofit digital IP cameras in an analog CCTV CAT5e wired installations.
• Works with Megapixel, HD720, HD1080 and VGA (SD) cameras (see note, pg. 2).
Mechanical:
• Dimensions (W x L x H approx.): Pace1PRM/Pace1PTM:
3.5” x 3.5” x 1” (88.89mm x 88.89mm x 25.4mm)
I.T.E. 43KC
*See note on page 2.
Pace1PRMT - 1 -
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. Pace1PTM and Pace1PRM are not intended to be connected to outside plant leads and should be installed indoors within the protected premises. Pace1PRM and Pace1PTM are intended for indoor use only.
1. Pace1PRM installation: a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet switch/network, NVR or video server. b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked [PoE Input] (Fig. 2, pg. 3). c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 OUT] (Fig. 2, pg. 3). UTP: Connect UTP to connector marked [UTP OUT] (Fig. 2, pg. 3).
2. Pace1PTM installation: a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity of camera/device. b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3). c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 IN] (Fig. 2, pg. 3). UTP: Connect UTP to connector marked [UTP IN] (Fig. 2, pg. 3).
Technical Specifications:
Parameter Description
Connections RJ45 for ethernet link or single pair UTP.
Input power requirements
Indicators
Environmental Conditions
Regulatory Compliance
Weights (approx.) Product: 3.88 oz. (0.11 kg.), Shipping: 6.70 oz. (0.19 kg.)
Midspan or endspan port connected. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W)
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity. Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T. Green: PoE Active.
Operating Ambient Temperature: UL60950-1
Pace1PRM: --- 4ºF to 120.2ºF (-- 20ºC to +49ºC). Pace1PTM: -- 4ºF to 120.2ºF (-- 20ºC to +49ºC).
Relative humidity: 20 to 85%, non-condensing. Storage Temperature: -- 22º to 158ºF (-- 30º to +70ºC) Storage Operating Altitude: -- 1000 to 6,561.679 ft. (-- 304.8 to 2000m).
UL/CUL Listed for Information Technology Equipment (UL 60950-1). CE approved. C-Tick compliant.
Fig. 1 Pace1PRM Pace1PTM
Single UTP
from
Pace1PTM
CAT5 or higher
from Pace1PTM
Green LED
indicates
PoE being
transmitted
to Pace1PTM
Green LED
indicates
PoE Present
from Midspan/
Endspan
Structured
Cable to
Midspan/
Endspan
Single UTP
from
Pace1PRM
CAT5 or higher
from Pace
receiver
Green LED
indicates
PoE received
from Pace1PRM
Green LED
indicates
PoE transmitted
to Camera/Device
Structured
Cable from
Camera/Device
*Note: Caution, once PoE connection is established between Pace1PRM and Pace1PTM, disconnection from Pace1PTM will not disable the PoE output voltage on the Pace1PRM, although the Pace1PTM can be reconnected, caution should be taken not to connect the CAT5e or single UTP wiring from Pace1PRM to any non-PoE device.
- 2 - Pace1PRMT
Single PoE camera connection:
Pace1PTM
Pace1PRM
Fig. 2 Fig. 2a
Mounting Hole
Pace1PRM - Receiver
IP-UTP Receiver
RJ45 LEDs Yellow - Activity Green - Speed Green LED Power and PoE
I.T.E. 43KC
UTP Link
Passes PoE/PoE+
Z1409
Output
RJ45
PoE
Link
LED
www.altronix.com
Input
100m max.
Powered Switch or NetWay MidSpan
Fig. 3
100m (328 ft.) max.
Pace1PTM - Transceiver
IP-UTP Transceiver
RJ45 LEDs Yellow - Activity Green - Speed Green LED Power and PoE
Input
PoE
PoE LED
I.T.E. 43KC
UTP Link
Passes PoE/PoE+
Z1409
Input
RJ45
PoE
Link
LED
www.altronix.com
Output PoE Out
PoE Camera
PoE LED
PoE+ over CAT5e up to 500m max.
or
Single UTP up to 152.4m max.
PoE compliant
100m max.
Legend:
Structured Cable or Single UTP
Multiple PoE camera connection:
Pace1PRM
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
Pace1PTM
PoE compliant
100m (328 ft.) max.
PoE Camera
Powered Switch or
100m (328 ft.) max.
100m (328 ft.) max.
100m (328 ft.) max.
NetWay MidSpan
Pace1PRM
Pace1PRM
Pace1PRM
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
Pace1PTM
Pace1PTM
Pace1PTM
PoE compliant
100m (328 ft.) max.
PoE compliant
100m (328 ft.) max.
PoE compliant
100m (328 ft.) max.
Legend:
Structured Cable or Single UTP
PoE Camera
PoE Camera
PoE Camera
Pace1PRMT - 3 -
Maximum Length of CAT5e Type vs. Camera Power/PoE Class:
Camera Power/PoE Class
Single UTP - 23AWG CAT5 or Higher
Max. Length (ft./meters)
13W/0 500/500 1,500/335.28 4W/1 500/500 1,500+/457.20+
6.5W/2 500/500 1,500+/457.20+ 13W/3 500/500 1,500/335.28 19W 500/500 1,000/335.28 25W 500/500 700/335.28
Note: Higher gauge wiring will allow for longer distances.
Notes:
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail: info@altronix.com, Lifetime Warranty, Made in U.S.A. IIPace1PRMT A27O
- 4 - Pace1PRMT
MEMBER
Loading...