Altronix NETWAYSP4P, NETWAYSP4P2 Installation

Power over the Ethernet

Installation Guide

Models Include:

NetWaySP4P

- 4-port Fiber Optic Transceiver with Built-in Power Supply for
Composite Fiber (Powered) Cable

NetWaySP4P2

- 4-port Fiber Optic Transceiver with Power-Limited Outputs for
Composite Fiber (Powered) Cable

DOC#: NETSP Rev. 020217

More than just power.

TM

Table of Contents:

Overview .................................................................................................pg. 3

Features .......................................................................pg. 3

Installation Instructions ..........................................................pg. 3

Recommended Altronix SFP Modules ..............................................pg. 4

Typical Applications ............................................................pg. 5

Technical Specifications ..........................................................pg. 6

Mounting Options ..............................................................pg. 8

- 2 - NetWaySP4P / NetWaySP4P2

Altronix NetWaySP4P/NetWaySP4P2 Fiber Optic Transceivers provide four (4) 1Gb SFP ports and four (4)
ports for up to 120W per port to be transmitted over composite fiber (powered) cable (fiber + copper combined)
to NetWay Spectrum PoE Hardened Switches. NetWaySP4P/NetWaySP4P2 can be used for standard fiber cable
applications as well.

Features:

Overview:

Agency Listings:

• UL/cUL UL 60950-1 (Information
Technology Equipment).

• CE European Conformity.

Input:

• 115VAC, 60Hz, 3.25A or 230VAC, 50/60Hz, 2A.

Power:
NetWaySP4P:

• Four (4) 56VDC non power-limited outputs
up to 120W max. full power per port.
Total power: 240W.

• IEEE 802.3af and IEEE 802.3at compliant
(PoE/PoE+).

• Short circuit protection.

NetWaySP4P2:

• Four (4) 56VDC power-limited outputs up to
60W max. full power per port.
Total power: 240W.

• Short circuit protection.

Fiber Port:

• Four (4) Gigabit SFP ports.

• Use with SFP module 1000Base-X (1Gb),
compliant to Class 1 laser product (not included).

Ethernet:

• Four (4) ports to swtich.

• Wire type: 4-pair CAT5e and higher.

• Connectivity: RJ45, auto-crossover.

• Speed: 10/100/1000Mbps.

• Distance: up to 100m.

Environmental:

• Refer to Environmental Conditions on page 6.

Battery Backup:

• Built-in battery charger
(optional rack mount battery enclosure - RE2).

• Automatic switchover to stand-by battery when
AC fails.

Compatible PoE Hardened Switches and
Accessories:

NetWaySP3WPN: 3-port PoE Hardened Switch
with (1) SFP port.
NetWay4EWPN: 4-port PoE Hardened Switch
with (1) SFP port.
NetWaySP4WPN: 4-port PoE Hardened Switch
with (2) SFP ports.
NetWaySP8WPN: 8-port PoE Hardened Switch
with (2) SFP ports.
RE2: Rack Mount Battery Enclosure
accommodates up to four (4)
12VDC/7AH batteries

Installation Instructions:

Wiring methods shall be in accordance with the National Elec­trical Code (ANSI/NFPA70), local codes, and the authorities
having jurisdiction. NetWaySP4P/NetWaySP4P2 is not in­tended to be connected to outside plant leads. These products
are for indoor use only and must be installed within the pro­tected premises.
NetWaySP4P must be installed in a restricted access area.
NetWaySP4P2, if battery bracket is removed, must be installed
in a restricted access area (Fig. 1b, pg. 3). The outputs are of a
non-limited power source.
For non-limited power sources, additional protective circuitry
and/or an appropriate fire enclosure for the products supplied
by this device are required.

1. Attach mounting brackets to the unit for rack or wall mount installation (Fig. 4 or 5, pg. 8).
Affix rubber pads to the unit for shelf installation (Fig. 6, pg. 8).

2. Secure the unit in a rack or on a wall, or place unit on a shelf as desired.
Note: The following factors should be taken into consideration when installing these rack mount units:
a. The unit is to be installed in a space where the maximum ambient temperature does not exceed
104ºF (40ºC).
b. Take care to ensure that there is sufficient air flow around the unit and that obstructions do not impede it.
c. When mounting units in a rack, take care to avoid uneven loading which can cause a hazardous condition.

3. Plug the grounded AC line cord (included) into the IEC 320 connector of the unit (Fig. 2f, pg. 4). Plug unit
into a reliable earth grounded socket. When using multiple units, the sum of the individual name plate ratings
should not exceed the supply circuit rating. Do not connect to a receptacle controlled by a switch.

NetWaySP4P / NetWaySP4P2 - 3 -

Fig. 1a Fig. 1b

4. Connect structured cable from ethernet switch/NVR (network video server) to RJ45 jack marked

Front Panel

[Ethernet 1-4] (Fig. 2e, pg. 4).
Note: All cabling and wire must be UL Listed and/or Recognized wire suitable for their application.

5. Connect Composite (Powered) Fiber cable: fiber portion to port marked [SFP 1-4], copper portion connects
to output marked [OUT 56VDC, 1-4] (Fig. 2b & 2d, pg. 4).

6. Connect opposite end of Composite (Powered) Fiber cable: fiber portion to SFP port on NetWay Spectrum
Hardened Switch, copper portion connects to power input of NetWay Spectrum Hardened Switch, carefully

observing correct polarity (Refer to NetWaySP3WPN/4WPN/8WPN / NetWay4EWPN Installation Guides).

7. When the use of stand-by batteries is required, they must be sealed lead acid or gel type. Use 14 AWG or
larger for all power connections. Connect four (4) 12VDC batteries in series to terminals marked [+ BAT –]
(Fig. 2h, pg. 4). Note: When batteries are not used, a loss of AC will result in a loss of output voltage.

Altronix P1MM and P1SM10 are hot-pluggable SFP fiber transceiver modules and are readily usable with all

Recommended Altronix SFP Modules:

Altronix Spectrum fiber optic equipment for 1Gb transmission rates.

P1MM - For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 - For use with Single-Mode Fiber for distances up to 10km.

Fig. 2

2b 2d2a 2c

Rear Panel

2a LED indicates AC Power is present.
2b 1Gb SFP port.
2c LED indicates fiber link.
2d 120W max output

2e RJ45 connects to switch

2f IEC 320 Connector: 115/230VAC (grounded line cord included).
2g Built-in battery charger: Charges stand-by batteries for applications requiring back-up.
(Optional rack mount battery enclosure available - RE2)

2e 2f 2g

- 4 - NetWaySP4P / NetWaySP4P2

PoE+

PoE+

Camera

Camera

WiFi Access

PoE Hardened Switch

NetWay Spectrum

Point

Copper

Connections

Stand-by Battery

Fiber

CopperFiber

Typical Application:

Composite (Powered) Fiber Cable

Input

115/230VAC

Data

PoE Hardened Switch

NetWay Spectrum

PoE+

Camera

Point

WiFi Access

Front Panel

Rear Panel

PoE+

Camera

NetWaySP4P / NetWaySP4P2 - 5 -

Fig. 3

Technical Specifications:

Parameter Description

Number of Ports

Power Outputs

Input power requirements

Environmental Conditions

Regulatory Compliance

Four (4) Gigabit SFP Ports. Four (4) ports 10/100/1000Mbps.

NetWaySP4P: Four (4) 56VDC non power-limited outputs 120W max.
NetWaySP4P2: Four (4) 56VDC power-limited outputs @ 60W each.

115VAC, 60Hz, 3.25A or 230VAC, 50/60Hz, 2.0A.

Operating Ambient Temperature (120W): – 40ºC to 50ºC (– 40ºF to 122ºF)
Relative Humidity: 85%, +/– 5%
Storage Temperature: – 40ºC to 85ºC (– 40ºF to 185ºF).
Operating Altitude: – 304.8 to 2,000m.

UL/cUL Listed for Information Technology Equipment
(UL 60950-1).

I.T.E. 43KC

CE European Conformity.

Weights (approx.)

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may
be of sufficient magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.

Product: 3.8 lbs. (1.7kg) | Shipping: 6.0 lbs. (2.7kg)

CAUTION: To reduce the risk of electric shock do not open
enclosure. There are no user serviceable parts inside. Refer servicing
to qualified service personnel.

- 6 - NetWaySP4P / NetWaySP4P2

Notes:

NetWaySP4P / NetWaySP4P2 - 7 -

Mounting Options:

Rack Mount Installation

1. Remove and discard factory installed screws from both sides of rack chassis (Fig. 4a).

2. Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B)
(included) (Fig. 4b).

3. Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 4c).

Fig. 4

Fig. 4a

Fig. 4b

Fig. 4c

Top Top

Front
Left

A

Remove

Front
Left

B

Wall Mount Installation

1. Install mounting brackets (A) on the left and right side of rack chassis using
four (4) flat head screws (B) (included) (Fig. 5a).

2. Place unit at desired location and secure with #6 size screws or larger (not included) (Fig. 5b).
Caution: It is necessary to make sure mounting screws are securely fastened
to a beam when installing the unit vertically.

Fig. 5

Fig. 5a

B

Fig. 5b

A

Top

Front Left

Dotted lines indicate studs behind sheetrock.

Shelf Installation

1- Position and affix rubber pads (C) (included) at each corner on the bottom of the unit (Fig. 6).
2- Place unit in desired location.

Fig. 6

Left Side

C

Rubber
Pad

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [e-mail] | Lifetime Warranty | Made in U.S.A.
IINetWaySP4P/NetWaySP4P2 H06R

- 8 - NetWaySP4P / NetWaySP4P2

Mounting Hardware (Included):

Two (2) mounting brackets

A

Six (6) flat head screws

B

for mounting brackets.

Four (4) rubber pads.

C

MEMBER