Altronix NETWAYSP3B, NETWAYSP3PL, NETWAYSP3WP, NETWAYSP3WPN, NETWAYSP3WPX Installation Guide

3-Port Ethernet over Fiber
PoE+ Hardened Switches

Installation Guide

Models include:

Embedded

™

NetWaySP3WP

- Includes Fiber Optic SFP 1G Link,
3-port PoE+ switch and power supply.

- NEMA4/4X, IP66 rated Outdoor enclosure.

NetWaySP3WPX

- Includes Fiber Optic SFP 1G Link,
3-port PoE+ switch and power supply.

- NEMA4/4X, IP66 rated Outdoor enclosure.

- Accommodates up to four (4)
12VDC/4AH batteries.

NetWaySP3X

- Includes Fiber Optic SFP 1G Link,
3-port PoE+ switch and power supply.

- NEMA1 rated Indoor enclosure.

NetWaySP3WPN

- Includes Fiber Optic SFP 1G Link and
3-port PoE+ switch
(uses external power supply).

- NEMA4/4X, IP66 rated Outdoor enclosure.

NetWaySP3PL

- Includes Fiber Optic SFP 1G Link,
3-port PoE+ switch and power supply.

- Backplane version.

NetWaySP3B

- Fiber Optic SFP 1G Link and
3-port PoE+ switch

- Board only.

I.T.E. 43KC

DOC#: NetWaySP3 Rev. 020917

More than just power.

TM

Altronix NetWay Indoor/Outdoor Ethernet over Fiber PoE+ Hardened Switches provide a 1Gb SFP port and
three (3) PoE+ (30W) ports or up to two (2) Hi-PoE (60W) ports, passing data and power to PoE/PoE+ compliant
devices. Cameras/edge devices may be located up to 100m from the unit. Features also include an integral battery
charger for applications requiring backup and embedded LINQ Technology to monitor, control, and report power
and diagnostics from anywhere.

Features:

Overview:

Input:

• 115VAC, 60 Hz, 2.5A or 230VAC, 50/60 Hz, 1.3A.
NetWaySP3B/NetWaySP3WPN:
48-55V UL Listed ITE power supply (up to 120W).

Power Output:

• Three (3) ports PoE+ (30W) or up to
two (2) Hi-PoE (60W) ports.

• IEEE 802.3at (30W) and IEEE 802.3af (15W)
compliant.

• 120W total power.

• Integral surge protection.

Fiber Port:

• One (1) Gigabit SFP port.

• Use with SFP module 1000Base-X (1Gb),
compliant to Class 1 laser product (not included).

Ethernet:

• Three (3) 10/100/1000 Mbps ports.

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair CAT5e or better structured cable.

• Distance: up to 100m.

• Speed: 10/100/1000Mbps, half/full duplex,
auto negotiation.

Battery Backup:

• Built-in charger for sealed lead acid or
gel type batteries.

• Automatic switch over to stand-by battery when
AC fails.

LEDs:

• Individual PoE On LEDs for each port.

• Individual IP Link status, 10/100Base-T/active
LEDs for each port.

• ALOS LED indicates fiber connection for SFP port.

• Heartbeat LED indicates proper operation of the unit.

Environmental:

• Refer to Technical Specifications Chart on page 4
for Environmental Conditions.

Applications:

• Provides PoE / PoE+ / Hi-PoE for cameras/devices.

LINQ Technology:

• Remote network management allows for camera/
device reset and monitoring.

• Provides local and/or remote access to critical
information via LAN/WAN.

• Email and Windows Dashboard Alert notifications
report real-time diagnostics.

• Event log tracks history.

Accessories:
NetWaySP1A

• Ethernet over Fiber Media Converter/Repeater ­ for applications requiring an additional SFP (Fiber)
port (Fig. 2, pg. 6).

Mechanical:
NetWaySP3WP

• NEMA4/4X, IP66 Rated enclosure for outdoor use.

• Dimensions (H x W x D approx.):

13.31” x 11.31” x 5.59”
(338.1mm x 287.3mm x 142mm).

NetWaySP3WPN

• NEMA4/4X, IP66 Rated enclosure for outdoor use.

• Dimensions (H x W x D approx.):

13.31” x 11.31” x 5.59”
(338.1mm x 287.3mm x 142mm).

NetWaySP3WPX

• NEMA4/4X, IP66 Rated enclosure for outdoor use.

• Accommodates four (4) 12VDC/4AH batteries
(48V of backup).

• Dimensions (H x W x D approx.):

17.53” x 15.3” x 6.67”
(445.3mm x 388.6mm x 169.4mm).

NetWaySP3X

• Dimensions (H x W x D approx.):

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm).

NetWaySP3PL

• Dimensions (H x W x D approx.):

10.75” x 8.875” x 2.375”
(273.1mm x 225.4mm x 60.3mm).

NetWaySP3B

• Dimensions (L x W x D approx.):

5.625” x 4.5” x 0.625”
(158.8mm x 142.9mm x 15.9mm).

• UL/cUL Listed for Information Technology Equipment (UL 60950-1),

Agency Listings:

Information Technology Equipment to Be Installed Outdoors (UL 60950-22).

• CE approved.

- 2 - NetWaySP3 Series

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local

NetWaySP3B

Metal Standoffs

Input:

48V-56VDC

3.3V PWR

+--

codes and authorities having jurisdiction. All units should be installed by a trained service personnel.

NetWaySP3WP/SP3WPN/SP3WPX Enclosure Mounting and Installation:

1. Remove backplane from enclosure prior to drilling. Do not discard hardware.
Note: Make sure that hardware will not interfere with components of the circuit board.

2. Mark and drill desired inlets on the enclosure to facilitate wiring. Maximum NEMA type 4X rated fittings to
be used are 0.5”. Follow manufacturer’s specifications for the appropriate size opening.
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
UL Listed NEMA type 4X rated conduit connector/hubs shall be used for the appropriate size inlets.

3. Clean out the inside of enclosure before remounting circuit board.

4. Mounting NEMA4/4X rated enclosure (Enclosure Dimensions, pgs. 11-12):
Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom holes of
the enclosure flange. Secure enclosure with appropriate fasteners (e. g. screws and anchors;
bolts and locking nuts, etc.) that are compatible with mounting surface and are of sufficient
length/construction to ensure a secure mount (Fig. 4, pg. 8).
Pole Mount: Refer to Figs. 5 - 9, pg. 8.

NetWaySP3WPX only: In order to properly mount NetWaySP3WPX on a pole using Altronix PMK1,
additional holes need to be drilled in the enclosure’s flanges, so the distance between those holes is 10”.

Note: All inlets for conduit fittings should be on the bottom of the enclosure.

5. Mount backplane in enclosure with hardware.

6. To facilitate wire entry utilize weather-tight NEMA rated connectors (supplied), bushings, and cable.

NetWaySP3X Enclosure Mounting and Installation:

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two (2) upper fasteners and screws in the wall with the screw heads protruding.
Place the enclosure’s upper keyholes over the two (2) upper screws; level and secure. Mark the position of
the lower two (2) holes. Remove the enclosure. Drill the lower holes and install two fasteners. Place the
enclosure’s upper keyholes over the two (2) upper screws. Install the two (2) lower screws and make sure to
tighten all screws (Enclosure Dimensions, pg. 9). Secure enclosure to earth ground.

NetWaySP3B/SP3PL Mounting and Installation:

1. Mount board/backplane in the desired location/enclosure
with hardware supplied.

2. NetWaySP3B: Connect 56VDC/120W max power source
to terminal marked [+] and [–].
Note: For proper earth ground connections on NetWaySP3B
fasten metal standoffs (provided) to threaded studs at indicated
board mounting holes (shown on the right).
This is recommended for better environmental immunity.

Installation:

1. For NetWaySP3WP, NetWaySP3WPX, NetWaySP3X, and NetWaySP3PL:
Before powering unit, set input voltage selection switch to proper Input Voltage position (Fig. 2a, pg. 6).
Units are factory set for 115VAC.

2. Secure cabinet to earth ground. Connect AC power from overcurrent protective device circuit breaker
(20A @ 115VAC, 60Hz, 16A @ 230VAC, 50/60Hz) to the terminals marked [L, N] on power supply board
(Fig. 2, pg. 6). Use 14AWG or larger for all power connections (Battery, DC output, AC input).
Connect ground lug to earth or green branch wire (12AWG min.).

Note: For NetWaySP3WPN use external 48-55V UL Listed ITE power supply, carefully observing
correct polarity (Fig. 3, pg. 7).
Keep power-limited wiring separate from non power-limited wiring by utilizing separate knockouts/
inlets. Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing
equipment. There are no user serviceable parts inside. Refer installation and servicing to qualified
service personnel.

3. Connect structured cables from port marked [Port 1], [Port 2] or [Port 3] on NetWay unit to PoE compliant
cameras/edge devices (Fig. 2, pg. 6).
Note: All interconnected devices must be UL Listed.

4. Insert SFP module into port marked [SFP], then connect cable to the SFP module on NetWaySP3B to the
corresponding input of an SFP switch (Fig. 2, pg. 6).

5. Battery Backup (if desired): Connect four (4) 12VDC batteries wired in series to terminals marked
[+ BAT –] (Fig. 2, pg. 6), carefully observing polarity.
When use of stand-by batteries is desired, they must be lead acid or gel type.
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.

6. Please ensure that the cover is secured with:
Key lock and screws for NetWaySP3X,

Installation Instructions:

Security bolt for NetWaySP3WP, NetWaySP3WPN and NetWaySP3WPX.

NetWaySP3 Series - 3 -

Altronix P1MM and P1SM10 are hot-pluggable SFP fiber transceiver modules and are readily usable with all
Altronix Spectrum fiber optic equipment for 1Gb transmission rates.

P1MM - For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 - For use with Single-Mode Fiber for distances up to 10km.

Technical Specifications:

Parameter Description

Recommended Altronix SFP Modules:

Number of Ports

Input Power
Requirements

Environmental
Conditions

Weights (approx.)

Three (3) ports PoE+ (30W) or up to two (2) Hi-PoE (60W) ports.
One (1) Gigabit SFP Port.

115VAC, 60Hz, 2.5A or 230VAC, 50/60Hz, 1.3A.
NetWaySP3B/NetWaySP3WPN: 48-55V UL Listed ITE power supply

Operating Ambient Temperature:
NetWaySP3WP/NetWaySP3WPX: 60W: -40ºC to 75ºC (-40ºF to 167ºF);
75W: -40ºC to 70ºC (-40ºF to 158ºF);
100W: -40ºC to 55ºC (-40ºF to 131ºF);
120W: -40ºC to 45ºC (-40ºF to 113ºF).

NetWaySP3X: 120W: -40ºC to 50ºC (-40ºF to 122ºF).

NetWaySP3B/NetWaySP3WPN: 120W: -40ºC to 75ºC (-40ºF to 167ºF).

Relative Humidity: 85%, +/- 5%
Storage Temperature: -40ºC to 85ºC (-40ºF to 185ºF).
Operating Altitude: -304.8 to 2,000m.

Model Product Weight Shipping Weight

NetWaySP3WP
NetWaySP3WPN
NetWaySP3WPX

NetWaySP3X

NetWaySP3PL

NetWaySP3B

10.32 lbs. (4.68kg)

7.7 lbs. (3.49kg)
15 lbs. (6.8 kg)

6.65 lbs. (3.02 kg)

2.6 lbs. (1.18 kg)

0.25 lbs. (0.11 kg)

11.7 lbs. (5.3kg)

10.0 lbs. (4.54kg)

17.5 lbs. (7.9kg)

7.55 lbs. (3.42kg)

4.0 lbs. (1.81kg)

0.75 lbs. (0.34kg)

Configuring Units for Network Connection

Please be sure to visit altronix.com for latest firmware and

installation instructions

Factory Default Settings

• IP Address: 192.168.168.168

• User Name: admin

• Password: admin

1. Set the static IP address for the laptop to be used for programming to the same network IP address as the
NetwaySP3. The default address of the NetwaySP3 is 192.168.168.168, E.I. 192.168.168.200.

2. Connect one end of the network cable to the network jack on the NetwaySP3 and the other to the network
connection of the laptop.

3. Open a browser on the computer and enter “192.168.168.168” into the address bar.
A dialog box Authentication Required will appear requesting both user name and password.
Enter the default values here. Click on the button labeled Log In.

4. The status page of the NetWaySP3 will appear. Click on the tab labeled Network Settings.
This will open the Network Setting screen. In this screen the MAC Address of the NetWaySP3 module will
be found along with the Network Settings and Email Settings.

Network Settings:

In the IP Address Method field select the method that the IP Address for the NetWaySP3 will be obtained
(STATIC or DHCP), then follow the appropriate steps.

- 4 - NetWaySP3 Series

Static:

A. IP Address: Enter the IP address assigned to the NetWaySP3 by the network administrator.
B. Subnet Mask: Enter the Subnet of the network.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
Gateway configuration is required to properly receive emails from the device.
D. HTTP Port: Enter the HTTP port number assigned to the NetWaySP3 module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not
encrypted and unsecure. Even though HTTP can be used for remote access, it is recommended primarily
for use with LAN connections.
E. HTTPS Port: Enter the HTTPS port number assigned to the NetWaySP3 module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 443.
Being encrypted and more secure, HTTPS is highly recommended for remote access.
F. Click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.

DHCP:

A. After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.
Next, click on the button labeled Reboot Server. After rebooting the NetWaySP3 will be set in the DHCP
mode. The IP address will be assigned by the router when the NetWaySP3 is connected to the network.
It is recommended to have the assigned IP Address reserved to ensure continued access
(see the network administrator).
B. Subnet Mask: When operating in DHCP, the router will assign the subnet mask values.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
D. HTTP Port: Enter the HTTP port number assigned to the NetWaySP3 module by the network administrator
to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and
unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with
LAN connections.
E. HTTPS Port: Enter the HTTPS port number assigned to the NetWaySP3 module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 443.
Being encrypted and more secure, HTTPS is highly recommended for remote access.
F. Click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.

Heartbeat Timer:

The heartbeat timer will send a trap message indicating that the NetWaySP3 is still connected and communicating.

Setting the Heartbeat Timer:

1. Click the button labeled Heartbeat Timer Setting.

2. Select the desired time between heartbeat messaging in the Days, Hours, Minutes and Seconds in
corresponding fields.

3. Click the button labeled Submit to save setting.

Factory Reset Option:

1. Power the unit down. Allow approximately 30 seconds for the unit to power down completely.

2. Depress Factory Reset button on NetWaySP3B while reapplying power to the unit (Fig. 1, pg. 5; Fig. 2b, pg. 6).
Continue holding the button until the LEDs on board go through the start up cycle, then release the button.

3. The unit returns to the original factory settings.

Link

Spd

Factory Reset

NetWaySP3 Series - 5 -

Brooklyn, NY US

www.altronix.com

Altronix Cor

Link

Spd

NetwaySP3B

Factory Reset

Fig. 1

PORT2
Spd: 10/100/1000
PoE: 30W/60W

PoE_Data

PoE_SPR

PoE/PoE+

or Hi-PoE Device

Fig. 2b

Factory Reset

NetwaySP3B

Spd

Link

Altronix Cor

Brooklyn, NY US

www.altronix.com

Switch

Fiber to

PORT3 (Uplink)
Spd: 10/100/1000
PoE: 30W

ALOS

SFP

Spd
Link

PORT1
Spd: 10/100/1000
PoE: 30W/60W

PoE_Data

PoE_SPR

Spd

Link

PoE/PoE+

or Hi-PoE Device

3.3V PWR

Batteries

To Stand-by

--- DC ++ BAT –

Typical Applications:

Power Supply Board Orientation

Factory Reset

+

--

5A 250VA

230VAC 115VAC

Input:

48V-56VDC

PoE

Fig. 2a

230VAC 115VAC

Device or

IP PoE/PoE+

NetWaySP1A

LGN

230VAC 115VAC

Input Voltage

Selection Switch

Fig. 2a

Input Voltage

LGN

230VAC 115VAC

5A 250VA

Selection Switch

--- DC ++ BAT –

board

To Input of

NetWaySP3B

Input

115/230VAC

NetWaySP3X - Power Supply Board Orientation NetWaySP3WP and NetWaySP3WPX

- 6 - NetWaySP3 Series

Fig. 2

Batteries

To Stand-by

Power Requirements Power Cabling Maximum Distance (ft./m)

y

15W 12/2 11,162’ / 3403m

30W 12/2 5,581’ / 1702m

45W 12/2 3,767 / 1,148m

60W 12/2 2,739’ / 835m

75W 12/2 2,249’ / 686m

90W 12/2 1,872’ / 571m

105W 12/2 1,607’ / 490m

120W 12/2 1,408’ / 429m

15W 16/2 4,415’ / 1,346m

30W 16/2 2,207’ / 673m

NetWaySP3WPN – Typical Application with Composite Cable

Power Distance Chart

45W 16/2 1,490’ / 454m

Typical Applications:

NetwaySP3B

PORT2
Spd: 10/100/1000
PoE: 30W/60W

PoE_Data

PoE_SPR

IP PoE/PoE+

or Hi-PoE Device

Spd

Link

Altronix Cor

Brooklyn, NY US

www.altronix.com

60W 16/2 1,083’ / 330m

75W 16/2 889’ / 271m

SFP

Spd
Link

90W 16/2 740’ / 226m

105W 16/2 635’ / 194m

PORT3 (Uplink)
Spd: 10/100/1000
PoE: 30W

Fiber Switch

48-55V UL Listed

ITE Power Supply

Carefully observe polarit

Cable

120W 16/2 557’ / 170m

Estimated distances based on starting voltage of 56VDC and accounts for a 10 volt drop.

ALOS

Composite

All distances are per IEEE 802.3at standard for device power requirements of minimum

44VDC and leave an approximate 2 volts for safety and flexibility.

3.3V PWR

Spd

Link

Factory Reset

PoE

IP PoE/PoE+

Input:

+

--

observe

Carefully

48V-56VDC

polarity

Device or NetWaySP1A

PORT1
Spd: 10/100/1000
PoE: 30W/60W

PoE_Data

PoE_SPR

IP PoE/PoE+

or Hi-PoE Device

NetWaySP3 Series - 7 -

Fig. 3

Wall Mount Installation

1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 4, pg. 8).

Fig. 4

Pole Mounting Using Optional Pole Mount Kit PMK1 (not included):

This installation should be made by qualified service personnel. This product contains no serviceable parts.
PMK1 is intended for use with Altronix outdoor rated power supplies or accessories housed in WP1, WP2, WP3
and WP4 enclosures. Brackets are designed for use with the Wormgear Quick Release Straps (two included).

1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 5, pg. 8).

2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 6, pg. 8 and Fig. 8, pg. 8).

Fig. 7

Fig. 9a
5” (127mm) square pole

Fig. 8

Fig. 6

Fig. 9
2” to 8”(50.8mm to 203.2mm)
diameter round pole

Fig. 5

3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 7, pg. 8).

4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting bracket
(Fig. 5, pg. 8).

5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 7, pg. 8).

6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 5, pg. 8).

7. Clip excess straps.

- 8 - NetWaySP3 Series

1.40”

(

)

(

)

(

)

(36mm)

NetWaySP3X

Mechanical Drawing and Dimensions (H x W x D approx.):

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)

1.20”

(31mm)

0.75”

(19mm)

1.40”

(36mm)

4.85”

(123mm)

12.5”

(318mm)

11.0”

(279mm)

4.85”

(123mm)

(36mm)

1.40”

0.75”

(19mm)

1.20”

(31mm)

0.9375”
(24mm)

3.25”

(83mm)

1.20”

(31mm)

1.40”

(36mm)

5.10”

(130mm)

5.10”

(130mm)

3.25”

(83mm)

(330mm)

1.0”

(25mm)

5.10”

(130mm)

13.0”

6.5625”

(167mm)

0.9375”
(24mm)

3.25”

(83mm)

3.25”

(83mm)

1.0”

(25mm)

1.0”

25mm

10.5”

267mm

1.0”

25mm

- 9 - NetWaySP3 Series

NetWaySP3PL

Mechanical Drawing and Dimensions (H x W x D approx.):

10.75” x 8.875” x 2.375” (273.1mm x 225.4mm x 60.3mm)

8.875” (225.4mm)

8.25” (209.5mm)

0.25”

(6.4mm)

10.25”

(260.3mm)

10.75”

(273.1mm)

- 10 - NetWaySP3 Series

NetWaySP3WP and NetWaySP3WPN

Mechanical Drawing and Dimensions (H x W x D approx.):

13.31” x 11.31” x 5.59” (338.1mm x 287.3mm x 142mm)

10.25”
(260.4mm)

10-32 X 0.25” (6.4mm)

8.25” (209.6mm)

10.75” (273.1mm)

10.00”
(254mm)

12.00”
(304.8mm)

13.50”
(342.9mm)

12.75”
(323.9mm)

10-32 X 0.375” (9.6mm)

BRASS INSERT (X4)

BRASS INSERT (X2)

3.96”
(100.6mm)

PADLOCK LATCH ATTACHED WITH RIVETS

1.61”
(40.9mm)

11.31”
(287.3mm)

13.31”
(338.1mm)

STAINLESS STEEL PIANO HINGE

(Ø 0.375” (9.5mm) PADLOCK EYE).

5.59”
(142mm)

- 11 - NetWaySP3 Series

Ø 0.32 (8.1mm) MOUNTING HOLE

TYP. 4 PLACES

8.00” (203.2mm)

FRONT VIEW COVER REMOVEDRIGHT SIDE VIEWFRONT VIEW

END VIEW

SECTION A-A

AA

316 STAINLESS STEEL

PADLOCK LATCH ATTACHED

WITH RIVETS. Ø.375 PADLOCK EYE

17.36”

441 mm

12.00”

304.8mm

6.41”

162.8mm

10-32 X .250

BRASS INSERT

4 PLCS.

14.54” (369.3mm)

16.74”

425.2mm

0.125” (3.2mm)

14.25”

362mm

14.00” (355.6mm)

12.23” (310.6mm)

17.53”

445.3mm

16.00”

406.4mm

1.67”

42.4mm

5.00”
127mm

16.73”

425mm

15.3”

388.6mm

6.67”

169.4mm

4.94”

125.5mm

5.77”

146.6mm

0.75”

19.1mm
MOUNTING PLATE

Ø.32” (8.1mm)

WALL MOUNTING HOLE X 4

NetWaySP3WPX

Mechanical Drawing and Dimensions (H x W x D approx.):

17.53” x 15.3” x 6.67” (445.3mm x 388.6mm x 169.4mm)

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [e-mail] | Lifetime Warranty | Made in U.S.A.
IINetWaySP3 Series E02R

- 12 - NetWaySP3 Series

MEMBER