Altronix NETWAYSP1BT Installation Guide

NetWaySP1BT

802.3bt Media Converter/Injector

Rev. 081319

Installation Guide

Altronix NetWaySP1BT 802.3bt media converter/injector provides a single 802.3bt (4PPoE) port up to 90W
and accommodates Fiber (1000Base-X/SX/LX) or structured cable to transmit data. Units can be deployed with
structured cable, conventional single/multimode fiber or composite cable (fiber + copper combined).

Features:

Overview:

Agency Listings:

• CE European Conformity.

Input:

• 48-56VDC @ 1.9A (95W).

Fiber Port:

• One (1) 1Gb SFP port.

Refer below for recommended SFP modules.

PoE Port:

• Single port rated up to 90W max.

• IEEE 802.3af, 802.3at and 802.3bt compliant.

Data Port:

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair CAT5e and higher.

• Speed: 10/100/1000 Mbps.

• Distance: up to 100m.

LED Indicators (Refer to Fig. 1, Pg. 2):

• Yellow and Green LEDs (RJ45 jacks):
Yellow (left) LED: 10/100 Mbps.
Green (right) LED: 1000 Mbps.

• Green PoE LEDs:
Indicate PoE present.

• Green SFP (Fiber) LED:
Indicates SFP connection.

Environmental:

• Refer to Environmental Conditions on page 2.

Dimensions (W x L x H approx.):

3.375” x 3.8” x 1” (85.7mm x 96.5mm x 25.4mm).

Installation Instructions:

Unit is powered via 48VDC-56VDC. NetWaySP1BT is not intended to be connected to outside plant leads and
should be installed indoors within the protected premises.

1. Mount NetWaySP1BT in desired location utilizing the mounting hole (Fig. 1a, pg. 2). Use a proper
fastener and/or wall anchor when securing NetWaySP1BT with screw through its mounting hole to the wall.

2. Connect 48VDC-56VDC power source to terminals marked [48-56VDC – Input +].
Terminals accommodate up to 12AWG wires. Caution: Make sure to observe polarity.

3. Input Connections:
a. Connect structured cable from port marked [PoE Signal] on NetWaySP1BT to a PoE midspan/endspan
(Fig. 2, pg. 2).
b. Connect fiber optic cable to a fiber SFP module. Connect the module to the port marked [SFP] on the
NetWaySP1BT. Connect the other end of fiber cable to an SFP module of a remote device.
SFP LED will illuminate indicating data connection (Fig. 2, pg. 2).

4. Using 4-pair CAT5e or higher cable connect PoE load device to be powered to the port marked
[802.3bt Output] on NetWaySP1BT. After authentication and classification have been established,
[PoE Signal] LED will illuminate indicating PoE presence.

Altronix P1MM, P1SM10, P1AB2K and P1GCE are hot-pluggable SFP fiber transceiver modules and are readily

Recommended Altronix SFP Modules:

usable with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates.

P1MM - For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 - For use with Single-Mode Fiber for distances up to 10km.
P1AB2K - For use with Single Strand Single-Mode Fiber for distances up to 2km.
P1GCE - For use with CAT5e or better for distances up to 100m.

Fig. 1
Fig. 1a

NetWaySP1BT

802.3bt Converter/Injector

Input: 48–56VDC

Output: IEEE 802.3bt (90W)

48-56VDC

802.3bt

PoE

-- Input +

Output

Data

Signal SFP

Port

Fiber

Signal

IEEE 802.3af, 802.3at and 802.3bt

compliant port rated up to 90W max

48VDC to

56VDC

Input

Yellow LED

10/100 Mbps

-- +

Green LED
1000 Mbps

PoE LED indicates

PoE present

Ethernet Data Port

data connection

One (1) Gb

SFP port
for Fiber

SFP LED
Indicates

Fig. 2

48-56VDC Input from

UL Listed supply

PoE+ (90W) PTZ Data from Midspan/Endspan

CAT5e/6 CAT5e/6

Parameter Description

Ports

Input Power
Requirements

Indicators

Evironmental
Conditions

Regulatory
Compliance

Weights (approx.)

One (1) 1Gb SFP port, one (1) Data port.
One (1) IEEE 802.3af, 802.3at and 802.3bt compliant output port rated up to 90W max.

48-56VDC @ 1.9A (95W).

Yellow and Green LEDs (RJ45 jacks): IP Link status, 10/100/1000 Base-T/active.
PoE Green LED: Indicates PoE present.
Fiber Signal Green LED: Indicates SFP connection.

Temperature:
Operating (90W): – 40ºC to 75ºC (– 40ºF to 167ºF).
Storage: – 40ºC to 75ºC (– 40ºF to 167ºF).
Relative Humidity: 85% +/–5%.
Operating Altitude: – 304.8 to 2,000m.

Product: 0.25 lb. (0.11 kg) | Shipping: 0.3 lb. (0.14 kg).

Typical Application:

48-56VDC

-- Input +

NetWaySP1BT

802.3bt Converter/Injector

Input: 48–56VDC

Output: IEEE 802.3bt (90W)

802.3bt

Data

PoE

Output

Port

Signal SFP

NetWaySP1BT

Converts Ethernet or Fiber to

802.3bt PoE port

Fiber
Signal

Fiber

Technical Specifications:

CE European Conformity.

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [e-mail] | Lifetime Warranty | Made in U.S.A.
NetWaySP1BT H13S

MEMBER