Altronix NETWAY4ES Installation Guide

PoE Solutions

Installation Guide

Models Include:

NetWay4ES

- 4-Port PoE/PoE+ Switch

NetWay4ESK

- Kit includes: NetWay4ES and NetWay1D (60W Midspan Injector, 115VAC / 230VAC input)

I.T.E. 43KC

Rev. 120913

More than just power.

TM

Table of Contents:

Overview .................................................................................................pg. 3

Features .......................................................................pg. 3

Installation Instructions ..........................................................pg. 3

Technical Specifications ..........................................................pg. 4

Typical Applications

NetWay4ES powered by NetWay midspan/endspan ...................................pg. 5

NetWay4ES powered by NetWay1D midspan injector .................................pg. 6

NetWay4ES Chassis Mechanical Drawing & Dimensions ..............................pg. 8

Shelf Installation ................................................................pg. 8

- 2 - NetWay4ES / NetWay4ESK

NetWay4ES is a 4-Port PoE/PoE+ switch which is designed for installation at the IDF (Intermediate Distribution
Frame). NetWay4ES allows for system expansion by accommodating up to four (4) IP cameras/devices over
a single CAT-5e or higher structured cable. Power up to 60W is provided by NetWay1D midspan injector
(included in NetWay4ESK Kit), or 30W by NetWay midspan/endspan, or any IEEE 802.3at standard midspan/
endspan typically located at the MDF (Main Distribution Frame).

Features:

Overview:

Agency Listings:

• UL 60950-1 Information Technology Equipment.

• CE European Conformity.

Input:

• Up to 60W is provided by NetWay1D midspan
injector or 30W by NetWay midspan/endspan or
any IEEE 802.3at standard midspan/endspan.

Power Output:

• Maximum power per port: PoE+ (30W).

• Total maximum power:
NetWay4ES - PoE+ (30W).
NetWay4ESK - 60W from Netway1D.

Ethernet:

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair CAT5e or higher
structured cable.

• Distance: up to 100m.

• Speed: 10/100BaseT, half/full duplex,
auto negotiation.

LED Indicators:

• Yellow - IP Link status,
Green - 10/100Base-T/active.

Environmental:

• Operating Ambient Temperature:

NetWay1D: 30W: -30ºC to 50ºC (-22ºF to 122ºF).
60W: -30ºC to 40ºC (-22ºF to 104ºF).
NetWay4ES: 60W: -40ºC to 75ºC (-40ºF to 167ºF).

• Storage Temperature:
NetWay1D: -30ºC to 85ºC (-22ºF to 185ºF).
NetWay4ES: -40ºC to 75ºC (-40ºF to 167ºF).

• Humidity: 20 to 85%, non-condensing.

Applications:

• Remote installation and powering of a
4-port PoE+ switch.
Star expansion of remote node to 4-PoE+
cameras/devices.

Mechanical:

• Dimensions (H x W x D approx.):
NetWay1D: 1.75” x 4.125” x 7.25”
(44.4mm x 104.8mm x 184.1mm).
NetWay4ES: 1.7” x 5.23” x 8.42”
(43.18mm x 132.8mm x 213.9mm).

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local
codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the
application. Midspan or endspan and NetWay4ES/NetWay4ESK is not intended to be connected to outside
plant leads and should be installed indoors within the protected premises. The midspan or endspan injector and
NetWay4ES/NetWay4ESK are intended for indoor use only.

1. Midspan or Endspan installation: Please refer to the corresponding installation instructions.

2. NetWay1D installation (Fig. 1, pg. 4):
a. Affix rubber pads to NetWay1D for shelf installation (Fig. 4, pg. 8).
b. Plug the grounded AC line cord (included) into the IEC 320 connector of the NetWay1D unit.
Plug unit into a reliable earth grounded socket.
When using multiple units the sum of the individual name plate ratings should not exceed the supply
circuit rating.
Note: Do not connect to a receptacle controlled by a switch.
c. Connect structured cable from UL Listed ethernet switch or video server to RJ45 jack marked [IN] on
NetWay1D (Fig. 2, pg. 6).

3. NetWay4ES installation:
a. Mounting: Affix rubber pads to NetWay4ES for shelf installation (Fig. 4, pg. 8).
b. Connect structured cable from NetWay4ES to RJ45 jack marked [OUT] to NetWay1D (Fig. 2, pg. 6) or
midspan or endspan (Fig. 1, pg. 5).
c. PoE ON LED of the NetWay1D will illuminate indicating PoE device is turned on (Fig. 2, pg. 6).
d. Connect IP cameras/devices to RJ45 jacks marked [1-4 PoE Output 10/100BaseT] (Figs. 1, 2, pgs. 5, 6).

NetWay4ES / NetWay4ESK - 3 -

Parameter Description

Input Power
Requirements

Output

Indicators

Environmental
Conditions

Regulatory
Compliance

Weights (approx.)

NetWay1D: 115VAC, 60Hz, 1.2A or 230VAC, 50/60Hz, 0.75A.
NetWay4ES: Powered by NetWay1D.

Maximum power per port: PoE+ (30W)
Total maximum power: Dependent on power from midspan or endspan.

NetWay1D:

Red LED: PoE ON.
Red LED: Power ON.

NetWay1D and NetWay4ES:

Yellow (RJ45 connector): On - Linked, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.

Operating Ambient Temperature (UL60950-1):
NetWay1D: 30W: -30ºC to 50ºC (-22ºF to 122ºF).

60W: -30ºC to 40ºC (-22ºF to 104ºF).
NetWay4ES: 60W: -40ºC to 75ºC (-40ºF to 167ºF).
Relative humidity: 85%, +/- 5%

Storage Temperature:
NetWay1D: -30ºC to 85ºC (-22ºF to 185ºF).
NetWay4ES: -40ºC to 75ºC (-40ºF to 167ºF).

Operating Altitude: 304.8 to 2,000m (-1,000 to 6,561.679 ft.).

UL 60950-1 Information Technology Equipment.
CE European Conformity

Product: 2.9 lb. (1.32 kg) | Shipping: 3.9 lb. (1.77 kg).

Technical Specifications:

- 4 - NetWay4ES / NetWay4ESK

Typical Applications:

NetWay midspan (MDF)

1 + 2 = maximum CAT-5e or higher structured cable distance 100m.

(Head End

Equipment)

Video Server

NVR Network

Switch

Ethernet

2

Up to

100m

1

IP Camera

max.

IP Camera

Note: Maximum 30W from NetWay4ES

INPUT

PoE

10/100

Output

NetWay4ES (IDF)

NetWay4ES / NetWay4ESK - 5 -

Fig. 1 - NetWay4ES powered by NetWay midspan/endspan

Base-T

NetWay1D

NetWay4ES

Aux.

ON

PoE

(Head End

Equipment)

Video Server

+ ---

NVR Network

(MDF)

Typical Application:

INOUT

INPUT

21

Switch

Ethernet

1 + 2 = maximum CAT5e or high structured cable distance 100m.

IP Camera

max.

Up to

100m

IP CameraIP Camera

max.

Up to

100m

max.

Up to

Up to

100m

max.

100m

IP Camera

(IDF)

PoE

10/100

Output

Base-T

- 6 - NetWay4ES / NetWay4ESK

Fig. 2 - NetWay4ESK (Kit). NetWay4ES powered by NetWay1D midspan injector.

Notes:

NetWay4ES / NetWay4ESK - 7 -

B

A

C

NetWay4ES Chassis Mechanical Drawing & Dimensions

(H x W x D approx.):

1.7” x 5.23” x 8.42” (43.2mm x 132.8mm x 213.9mm)

Fig. 3

5.23”

(132.84mm)

(213.87mm)

8.42”

(43.18mm)

1.7”

Output

10/100

Base-T

PoE

INPUT

Shelf Installation

1- Position and affix rubber pads (C) (included) at each corner on the bottom of the unit (Fig. 4).
2- Place unit in desired location.

Mounting Hardware (Included):

Four (4) rubber pads

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [e-mail] | Lifetime Warranty | Made in U.S.A.
IINetWay4ES D27R

- 8 - NetWay4ES / NetWay4ESK

Fig. 4

C

Left side

Rubber Feet

MEMBER