Altronix ALTV2432350, ALTV2432350CB, ALTV2432600, ALTV2432600CB Installation Guide

ALTV2432 Series

CCTV Power Supplies

Installation Guide

Models Include:

• ALTV2432 • ALTV2432CB

- 24VAC @ 8A (200VA) - 24VAC @ 8A (200VA)
or 28VAC @ 7A (200VA). or 28VAC @ 7A (200VA).

- Thirty-two (32) Fuse Protected Outputs. - Thirty-two (32) PTC Protected Outputs.

• ALTV2432350 • ALTV2432350CB

- 24VAC @ 14A (350VA) - 24VAC @ 14A (350VA)
or 28VAC @ 12.5A (350VA). or 28VAC @ 12.5A (350VA).

- Thirty-two (32) Fuse Protected Outputs. - Thirty-two (32) PTC Protected Outputs.

• ALTV2432600 • ALTV2432600CB

- 24VAC @ 28A (700VA) - 24VAC @ 28A (700VA)
or 28VAC @ 25A (700VA). or 28VAC @ 25A (700VA).

- Thirty-two (32) Fuse Protected Outputs. - Thirty-two (32) PTC Protected Outputs.

Rev. 021704

Overview:

ALTV2432 Series CCTV Power Supplies provide 24VAC/28VAC distributed via thirty-two (32) fuse or PTC protected
outputs for powering CCTV Cameras, heaters and other video accessories.

Thirty-two (32) Output ALTV2432 Reference Chart:

Total

Output
Altronix
Model Number

ALTV2432

ALTV2432CB

ALTV2432350

ALTV2432350CB

ALTV2432600

ALTV2432600CB

Output

Voltage

24VAC 8A
28VAC 7A
24VAC 8A
28VAC 7A
24VAC 14A
28VAC 12.5A
24VAC 14A
28VAC 12.5A
24VAC 28A
28VAC 25A
24VAC 28A
28VAC 25A

Current
(Power)

Input:

• 115VAC, 50/60Hz.

Output:

• Thirty-Two (32) fuse or PTC protected outputs.

• 24VAC or 28VAC supply current

• Outputs are rated @ 3.5A (fuse) or 2.5A (PTC).

• Surge suppression.

PTC

Number of

Outputs

32

Protected

Outputs

Specifications:

Features:

• Secondary fuse rated @ 10A/250V.

• AC power LED.

• Power ON/OFF switch.

• Spare fuses provided.
(all models w/primary and/or secondary fuses).

Mechanical:

• Enclosure Dimensions (H x W x D approx.):

13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)

P

P

P

Output

Fuse

Protected

Outputs

-

-

-

P

- 2.5A

P

- 2.5A

P

- 2.5A

Current

(max per

output)

3.5A

3.5A

3.5A

115VAC

50/60Hz Input

Current

2.9A

2.7A

5.4A

Installation Instructions:

1. Mount unit in the desired location.

2. Turn main switch on the unit OFF (Figs. 1-3, pgs. 4-6).

3. All units are factory set for 24VAC operation.
For 28VAC operation, adjust unit prior to mounting and applying power as follows:
Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and the yellow wire
[24V] is connected to the terminal marked [S].

4. Connect AC power to the black and white flying leads of the transformer(s) (Figs. 1-3, pgs. 4-6), secure green lead
to earth ground. Use 18 AWG or larger for all power connections.

5. Measure output voltage before connecting devices. This helps avoiding potential damage.
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting
the output voltage.

6. Connect devices to the terminals marked [1P - 1N] through [16P - 16N] on PD16W/PD16WCB board
(Figs. 1-3, pgs. 4-6), carefully observing polarity. Terminals marked [1P - 16P] are of the same polarity.

7. Turn main switch on the unit to the ON (RESET) position (Figs. 1-3, pgs. 4-6).

8. Green LED(s) will illuminate when unit is powered.

9. Upon completion of the wiring secure enclosure door with screws (supplied).
CAUTION: Equipment to be installed/serviced by authorized / trained personnel only.
Shut branch circuit power before installing/servicing equipment.

- 2 - ALTV2432 Series

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes. Use 75 C or higher rated UL insulated wiring for connecting the unit
to the mains.

Terminal Identification:

PD16W - Power Distribution Module

1P - 16P AC output.
1N - 16N AC output.

ALTV2432 Series - 3 -