Altronix ALTV1224DCCB220, ALTV1224DC1CB220, ALTV1224DC2CB220, ALTV1224DCCB, ALTV1224DC1 Installation Manual
...
ALTV1224DC220 Series
CCTV Power Supplies
Installation Guide
Models Include:
• ALTV1224DC220 • ALTV1224DCCB220
- 12VDC or 24VDC @ 4A. - 12VDC or 24VDC @ 4A.
- Eight (8) Fuse Protected Outputs. - Eight (8) PTC Protected Outputs.
• ALTV1224DC1220 • ALTV1224DC1CB220
- 12VDC or 24VDC @ 4A. - 12VDC or 24VDC @ 4A.
- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
• ALTV1224DC2220 • ALTV1224DC2CB220
- 12VDC or 24VDC @ 6A. - 12VDC or 24VDC @ 6A.
- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
Rev. 022505
Overview:
D1
INPUT
R1
LED
Used on PTC Models
(example: ALTV1224DCCB220)
220VAC
power
mains
Divider
ALTV1224DC220 Series DC CCTV power supplies are designed to power CCTV Cameras and accessories. Units provide
12VDC or 24VDC distributed via eight (8) or sixteen (16) fused or PTC protected outputs with a total of 4A or 6A total
continuous supply current.
Eight (8) or Sixteen (16) Output ALTV1224DC Reference Chart:
Altronix
Model Number
ALTV1224DC220
ALTV1224DCCB220
ALTV1224DC1220
ALTV1224DC1CB220
ALTV1224DC2220
ALTV1224DC2CB220
Output
Voltage
12VDC
or
24VDC
Total
Output
Current
(Power)
4A
6A 16
Number
of
Outputs
8
16
PTC
Protected
Outputs
-----
P
-----
P
-----
P
Fuse
Protected
Outputs
P
----- 2.5A
P
----- 2.5A
P
----- 2.5A
Output
Current
(max per
output)
3.5A
3.5A
3.5A
220VAC
50/60Hz
Input
Current
0.9A
1.5A
Input:
• Input 220VAC (working range 198VAC-256VAC),
50/60 Hz.
Output:
• Eight (8) or sixteen (16) fuse or PTC protected outputs.
• 12VDC or 24VDC.
• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
• Filtered and electronically regulated outputs.
Specifications:
Features:
• AC input and DC output LED indicators.
• Power ON/OFF switch.
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates
costly labor.
Enclosure Dimensions (H x W x D approx.):
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm).
Installation Instructions:
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install two fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 6).
Secure enclosure to earth ground.
2. Slide switch to OFF position (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).
3. Set the unit to desired DC output voltage range by setting switch (SW1) on the power supply board to the appropriate
position. Use trimpot to adjust voltage if necessary (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).
4. Connect AC circuit (220VAC, 50/60Hz) as follows: Green branch wire connects to earth (safety) ground lug .
Line and Neutral to the connector on power supply board marked [L, N] respectively
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).
5. Measure output voltage before connecting devices. This helps avoiding potential damage.
6. Connect each DC device to the output terminals 1 through 8 (Fig. 1, pg. 3) or terminals 1 through 16
(Fig. 2, pg. 4 or Fig. 3, pg. 5).
Note: Be careful to observe camera polarity.
7. When batteries are being used, the DC output voltage must be adjusted by turning the trim pot VR1
(Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5) clockwise to increase the output voltage to 13.7VDC for 12VDC
operation and 27.1VDC for 24VDC operation.
Connect battery to theterminals marked [-- BAT + ] (battery leads included) (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).
Use two (2) 12VDC batteries connected in series for 24VDC operation.
8. Slide switch to ON position (Fig. 1, pg. 3, Fig. 2, pg. 4 or Fig. 3, pg. 5).
9. Green LED on the PD8/PD8CB or PD16W/PD16WCB board will illuminate when power is present.
10. Upon completion of the wiring, secure enclosure door with screws (supplied).
WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.
- 2 - ALTV1224DC220 Series
ALTV1224DC/CB Terminal Identification:
CAUTION: De-energize unit prior to servicing. For continued protection against
OLS127220 - Power Supply
Terminal Legend Function/Description
L, N 220VAC power mains connection.
– DC + 12VDC or 24VDC @ 4A total continuous output.
– BAT + Stand-by battery connections. Maximum charge rate 0.5A.
PD8/PD8CB - Power Distribution Module
Terminal Legend Function/Description
1P - 8P Positive DC power outputs.
1N - 8N Negative DC power outputs.
Fig. 1
fire hazard replace fuse with the same type and rating. Do not expose unit to rain or moisture.
Divider
LED
Door
Wire Strap
(from
Enclosure
to Door)
Ground
Lug
220VAC
power
mains
OFF - 24V
ON - 12V
1 2 3 4 5 6 7 8
OFF ON
ON
ON
OFF - 24V
ON - 12V
Switch disables power mains
line voltage input.
If stand-by battery (batteries) are
connected the DC output remains on.
SW1
24VDC output - OFF
12VDC output - ON
INPUT
D1
R1
FUSED POWER OUTPUTS
COMMON POWER OUTPUTS
N
P
Used on PTC Models
(example: ALTV1224DCCB220)
Trimpot
Adjusts output voltage
on power supply
ALTV1224DC220 Series - 3 -
Loading...