Page 1
Jeep Wrangler
WRANGLER 1/22
Jeep Wrangler
X209-WRA-OR
X209-WRA-ORSXM
9” Restyle In-Dash System
Installation Manual
Model: Wrangler
Model Year: 2011-2018
Jeep
* The specified vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is
not guaranteed if the manufacturer has made production changes to the listed vehicles above.
Warning: Before you begin wiring, remove the ground wire from the negative
terminal of the battery. Failing to do so can lead to electric shock, injury or damage
to equipment.
Model Year
Wrangler 2011 - 2018
Introduction
Congratulations on purchasing the X209-WRA-OR. This installation manual is designed to take you through the
step-by-step installation of X209-WRA-OR into a 2011-2018 Jeep Wrangler. Please familiarize yourself with the
owners manual and if you still have additional questions please call 1-800-TECH-101.
Note
Design and specifications are subject to change without notice for improvement.
To Ensure Safe Use, Always Follow These Precautions
The installation of this product requires specialized skills and experience. We recommend that you have the
product installed by an Alpine authorized dealer.
Before you use this product, be sure to carefully read this installation manual and the separate user's manual
so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as
a result of failure to follow the instructions in the manuals.
This manual includes a number of symbols that are intended to help you use the product safely, to prevent
harm to you and others, and to protect against damage to property. These symbols and their meanings are
listed below. Make sure you fully understand these symbols before you begin reading the main text.
Explanations of Injury and Damage That May Result from Incorrect Use
Warning
Caution
Ignoring the content marked by this indication and using the product incorrectly is
expected to lead to death or serious injury.
Ignoring the content marked by this indication and using the product incorrectly is only
expected to lead to injury or property damage.
Page 2
Types of Precautions
Forbidden
Mandatory
Forbidden
Forbidden
Forbidden
Mandatory
Mandatory
Forbidden
Forbidden
Jeep Wrangler
WRANGLER 2/22
Indicates actions that are forbidden
(must not be performed)
Indicates that disassembly is
forbidden.
Indicates actions that are
mandatory (must be performed)
Marks content that should receive
your full attention.
Warning
Do not disassemble or modify the product. Doing so could lead to an accident, fire,
or electric shock.
Store screws and other small objects where small children cannot reach them. If one of these
small objects is swallowed, consult with a doctor immediately.
When replacing fuses, be sure to use fuses with the specified current rating. Failing to do so could
lead to an accident or fire.
Only connect the product to a 12 VDC negative ground car. Failing to do so could lead to
an accident or fire.
Before you begin wiring, remove the ground wire from the negative terminal of the battery.
Failing to do so could lead to electric shock or injury.
Do not cut the insulation on a cord and take power from another device. Doing so could
lead to fire or electric shock.
Do not install the product in a location where it will obstruct the driver’s forward view;
interfere with the operation of the steering wheel, gearshift, or the like; or pose a
threat to passengers. Doing so could lead to an accident or injury.
When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank,
electrical wiring, and the like. This kind of damage could lead to an accident or fire.
Page 3
Jeep Wrangler
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
WRANGLER 3/22
When installing and grounding the product, do not use any of the bolts or nuts of the
steering wheel, brakes, fuel tank, or the like. Doing so could make the brakes stop working
or lead to fire.
Do not install the product near the passenger-side airbag. Doing so could interfere with the
operation of the airbag and lead to an accident or injury.
Bundle cords so that they don’t interfere with driving. Wrapping cords around the steering
wheel, gearshift, brake pedal, or the like, could lead to an accident or damage equipment.
Caution
Connect the product properly according to the instructions. Failing to do so could lead
to fire or an accident.
Do not sandwich cords between the seat railing or allow them to touch protrusions.
Resulting breaks or shorts could lead to electric shock or fire.
Do not block vents or heat sinks. Doing so could lead to fire or damage equipment.
Use the accessories according to the instructions, and attach them securely.
Failing to do so could lead to an accident or damage equipment.
Do not install the product where it may be exposed to water or in a place with high levels
of humidity or dust. Doing so could lead to fire or damage equipment.
The installation and wiring of this product requires specialized skills and experience.
Have the product installed by an Alpine authorized dealer.
Page 4
Tools Required
Panel Removing Tool 7mm Sockets #2 Phillips Screwdriver
10mm Sockets Extension Ratchet
Wire Cutters Air Saw
Jeep Wrangler
WRANGLER 4/22
Accessory List
Installation Kit Parts (G-KTX-X209D-WRA)
X209-WRA-OR Radio Dash
Bezel
MENU
Microphone Rear Support Bracket
Key Harness Side Mounting Brackets
Page 5
Jeep Wrangler
WRANGLER 5/22
Accessory List
Head Unit Box Parts (X209D OR)
X209D OR DVD/Display Unit X209D OR Source Unit USB Extension Cable
AUX/Pre Out Harness GPS Antenna Documents
OM QR Card
Alpine
Registration Card
Direct Camera Adapter Display Cable
Source Unit HDMI Bracket
iDatalink Maestro Box Parts (ALP-MRR3/ALP-HRN-WRA2)
Maestro Flashing Cable Antenna Adapter iDatalink Maestro Module
DVD/Display HDMI Bracket
HDMI Cable
(8) 8mm Screws
QRG Navigation
Main Harness SAT Radio Antenna Adapter OEM USB Adapter
Page 6
Programming the iDatalink Maestro Module
Jeep Wrangler
WRANGLER 6/22
1 INSTALL THE WEBLINK PLUG-IN
Go to:
idatalinkmaestro.com/plugin and follow the installation steps. The
Maestro module must be programmed specically for each vehicle
and radio. Take care to enter the correct vehicle information,
factory options, head unit model, and head unit serial number.
The head units serial number is an alphanumeric value which is
found on the head units label, underneath the bar code.
Review the System Requirements before installing.
If the plugin is already installed, the caution, “The plugin is already
installed” appears. Please skip to step 2.
2 REGISTER A WEBLINK ACCOUNT
Go to:
idatalinkmaestro.com/register and complete the registration process.
A conrmation email will be sent to you requiring validation.
For existing customers, click log in.
3 CONNECT YOUR MAESTRO MODULE
Use your Maestro module to connect to your PC.
5 PROGRAM YOUR MODULE
Follow the programming steps for your vehicle.
4 LOG INTO WEBLINK
Go to:
idatalinkmaestro.com/login.
Enter your username and password, then click OK.
6 Once Programing is complete “FLASHING
COMPLETED!” will be displayed.
Proceed to the next page to complete installation.
NOTE: If serial number is invalid, Call ADS at
1-866-427-2999 with the serial number.
Page 7
Jeep Wrangler
WRANGLER 7/22
Component Locations
IMPORTANT: Follow the recommended component location shown below. Failure to do so, will result in poor
GPS performance.
Add-on Microphone
iDatalink Maestro Module
SAT-Radio Tuner
(Sold Separately)
Jeep SINCE 1941
Jeep
GPS Antenna Installation
IMPORTANT: Follow the GPS antenna installation procedure shown below. Failure to do so will result in poor
GPS performance for CarPlay, Android Auto, and off-road navigation.
GPS Antenna
Wire Hook
Peel the plastic layer
off from the double
side tape of the GPS
antenna and place the
GPS antenna on top of
the driver side roof
frame. T20 Torx to
remove the visor.
Page 8
Factory Unit Disassembly Process
Jeep Wrangler
WRANGLER 8/22
1 Remove the rubber cover from the top center
storage area and extract (1) 7mm screw.
3 Remove the window switch pod using a panel
removing tool and extract (1) 7mm screw.
2 Remove the knee cover panel and extract (2) 7mm
screws located to the right and left sides of the
steering wheel column.
Left side of
steering wheel
column.
Right side of
steering wheel
column.
4 Remove the dash panel.
5 Extract (4) 7 mm screws and remove the factory
radio.
6 Extract (2) 7 mm screws from the factory radio
bracket and remove it.
2
Page 9
Installation Instructions
Lock tab
Jeep Wrangler
WRANGLER 9/22
1 The factory dash panel needs to be trimmed to
allow the new X209-WRA-OR bezel to fit into place.
Remove the highlighted area by cutting along the
dashed line.
3 Use a cutting tool to trim the highlighted area
shown below.
2 Remove the vents from the radio section on the
OEM dash panel by pressing down on the lock tab
and turning right. Mount vents on to the X209-WRAOR bezel.
Rear view
4 Mount the microphone as illustrated and run the
cable to the radio cavity.
5 Plug the OBDII connector on to the OBDII port
below the driver side dash and run the extension to
the radio cavity.
6 Attach the Maestro to the main harness.
Page 10
Installation Instructions
Jeep Wrangler
WRANGLER 10/22
1 Attach the modified panel using the factory screws.
3 Attach the rear support bracket using (2) 7mm
factory screws.
2 Position X209D OR source unit on top of X209
DVD/Display unit as shown, and attach the
mounting brackets using the provided (8) 8mm
screws and rear support rubber cap screw.
4 Route the USB extension cable to the glove box,
connect the main harness and other adapters to the
factory harness and secure them.
5 Route the key harness through the top-left side of
the X209D OR source unit. Mount the X209D OR
source unit using (4) 7mm factory screws.
6 Connect the radio bezel and snap it into place.
A/C
A/C
Page 11
WRANGLER 11/22
Connecting the Uconnect® USB port (only for vehicles with factory Uconnect®)
Jeep Wrangler
1 Remove the factory climate control panel. It is
clipped on and can be removed with a panel
removing tool. Extract the (2) 7mm bolts from
Uconnect® module.
3 Connect the 4pin OEM connector to the OEM USB
adaptor (included).
5 Secure the Uconnect® module to the original
location using the 7mm bolts.
2 Disconnect the 4pin OEM connector.
4 Use the USB extension to connect USB adaptor to
the radio USB input.
USB
CAN I/F
GPS
SXM/DAB
HDMI IN HDMI OUT
POWERW. REMOTEPRE OUT
NOTE: if the factory Uconnect® system is not going
to be used you can unplug the 24 pin connector
shown in step 2. This should only occur for people
who do not want to use this feature. If Uconnect®
module is not disconnected the Uconnect® system
will stay paired with previously paired phones.
The user’s phone may connect to both Bluetooth
devices simultaneously resulting in unpredictable
and potentially distracting behavior.
Connecting A SiriusXM Module (Sold Separately)
CAN I/F
GPS
SXM/DAB
USB
HDMI IN HDMI OUT
POWERW. REMOTEPRE OUT
There is no way to integrate the factory SiriusXM
tuner. Once the radio is removed, the factory
SiriusXM is removed. As the title states, SiriusXM
requires a tuner sold separately. This diagram
shows how to integrate the antenna connection.
For vehicles with factory SiriusXM connect
the adapter to the factory SiriusXM antenna in
the radio cavity. The factory SiriusXM antenna
is located on the passenger side B-pillar.
For vehicles without factory SiriusXM use
the antenna that is included with the SXV300
SiriusXM Tuner.
SiriusXm
connect
Page 12
Jeep Wrangler
WRANGLER 12/22
Mounting Brackets
IMPORTANT: During the research and development of this product it was discovered that mounting tolerance
may vary from the vehicle’s trim level to year built. We have added a 1mm tolerance to the mounting brackets
to compensate for such variance in mounting tolerance. Use the guides below as reference if there are any
required adjustments.
Adjust the rear bracket as needed when the top or bottom is protruding or not flushed.
Adjust the side brackets as needed when either side is protruding or not flushed.
Page 13
Exploded-View Diagram
MENU
X209-WRA-OR
Radio Dash
Bezel
X209D OR Source Unit
Jeep Wrangler
WRANGLER 13/22
Dash Board
A
/C
Side Mounting
Brackets
Factory Vents and Window
Switch Pod (not included)
Bezel Wiring Diagram
8 Pin Harness
20 Pin Harness
(Connect to X209D OR)
8 Pin Harness
NOTE: If the 3-pin key
harness is not plugged
in the head unit will not
power on!!!!!
Page 14
X209-WRA-OR Wiring Diagram
Jeep Wrangler
WRANGLER 14/22
To OBDII Connector
Not
Used
Connector
10-pin Black
iDatalink MAESTRO Module
To Vehicle Connectors
OEM Audio
20-pin Gray
Connector
16-pin Green Connector
Red
Not
Used
Connector
18-pin Black
18-PinChime10-Pin
Power/Speaker
Front
Front
Reset
Button
Rear
Rear
Direct Camera Adapter
AMPLIFIED VEHICLES
Failure to follow this procedure will
result in no audio from Navigation and
Bluetooth sources.
For factory amplied vehicles switch the
speaker connectors, front to rear and
rear to front.
WARNING!
Front
Rear
Rear
Front
Direct Camera Input
If using
HCE-TCAM1-WRA
*
see page 18
X209D OR Source Unit
CAN I/F
GPS
SXM/DAB
USB
HDMI IN HDMI OUT
DISP. OUT
Microphone
3-Pin 4-Pin 3-Pin 4-Pin10-Pin
3-pin Black
For manual transmission vehicles ONLY. Connect the
Red - Acc 12V+
HCE-TCAM1-WRA
*
Yellow -12V+
Black - Ground
If using
see page 18
If using
KAC-001
*
see page 19
(Data)
Connector
4-pin Black
(Power)
Connector
3-pin Black
Connector
(Audio)
Blue
Not
Used
10-pin Green
Connector
(Vehicle signals)
MANUAL TRANSMISSION VEHICLES
White/Gray Manual Transmission Reverse Input
White/Gray wire to the White/Gray wire located
on the passenger side kick panel.
Blue/White Amp Turn-on
Blue Power Antenna
AUX Power
3-pin Black Connector
Rear View Camera
WARNING!
The use of this connection
is intended for Alpine
HCE-TCAM1-WRA rear
view camera ONLY.
Rear View Camera
6-pin Black Connector
HDMI Interface
6-pin White Connector
Cut loop when connecting
KCX-630HD HDMI selector
interface.
Main Harness
ANTENNA
Remote Harness
Power Harness
X209D OR DVD/Display
DVD/Display Power
8-pin White Connector
PRE OUT
EXT. KEY W.REMOTE
DISP IN
POWER
POWER
Key Harness
If
You
Forget
To
Plug
This
In
Unit
Will
Not
Power
On
Page 15
X209-WRA-OR With Optional HDMI Interface Wiring Diagram
X209D OR - Source Unit
To Optional Display
ANTENNA
Jeep Wrangler
WRANGLER 15/22
GPS
CAN I/F
SXM/DAB
USB
HDMI IN HDMI OUT
EXT. KEY W.REMOTE POWER
PRE OUT
DISP. OUT
For all phones the USB
power source needs to
be a 2A source. This will
require a separate USB
power source to be installed
in the vehicle.
Lightning to HDMI
For Android users most
Android phones do not have
HDMI adapters. The easiest way to
connect is with a Miracast adapter
(for example a Roku Stick
or Amazon Firestick).
Extension Cable
PAC HDMI-USB-CBL
Recommended
(Sold Seperately)
For iPhone the
adapter
is required
Or
HDMI/USB
KCX-630HD (Optional) HDMI Selector Interface
POWER
Cut loop when connecting
KCX-630HD HDMI selector
interface.
DISP IN
POWER
HDMI IN 1 HDMI IN 2HDMI OUT
X209D OR - DVD/Display
USB POWER
Do not use the head unit’s
USB to power HDMI devices.
This port is meant for Apple
CarPlay, Android Auto, and
USB ash drives.
Page 16
X209-WRA-OR Wiring Diagram
Jeep Wrangler
WRANGLER 16/22
To SiriusXM Tuner
Vehicle Antenna
GPS Antenna (Included)
PRE OUT cable
Interface cable
Power cable
W.REMOTE cable
DVD REMOTE
(Brown)
MON REMOTE
(Brown)
REMOTE IN
(Brown/White)
REMOTE OUT
(Brown)
DVD
(Red/White)
STEERING REMOTE
MIC IN
SPEED SENSOR
(Green/White)
CAMERA
IDATALINK I/F
AUX INPUT
REMO
(Blue/White)
REVERSE
(Orange/White)
P. ANT
(Blue)
PARKING BRAKE
(Yellow/Blue)
ACC
(Red)
BATT
(Yellow)
GND
(Black)
STATU S IN
(Green)
(Green/Black)
(White)
(White/Black)
(Gray/Black)
(Gray)
(Violet/Black)
(Violet)
To the vehicle speed pulse line
To Front, Rear or Side camera
To iDataLin
k module
To AUX output device or iDataLink
module
To amplier or equalizer
To plus side of the back lamp signal
lead of the car
To power antenna
To the parking brake signal lead
Ignition key
Battery
Rear Left
Front Left
Speakers
Front Right
Rear Right
To remote control input lead of
DVE-5300
To remote control input lead of Rear
Monitor
To remote control output lead
To remote control input lead
To remote control output lead of
DVE-5300
To steering remote control interface
box
SUBW
FRONT OUT
REAR OUT
Microphone (Included)
To input terminal of amplier when
adding an external amplier
Page 17
Wire Harness Pin Outs
Jeep Wrangler
WRANGLER 17/22
Radio Main
8
16
7
15
6
14
13
5
4
12
3
11
10
2
1
9
DVD Display
1
5
2
6
3
7
4
8
KAC-001 Power
3
2
1
Blue 22AWG
Red 20AWG
Blue/White 22AWG
Orange/White 22AWG
Yellow/Blue 22AWG
Purple 20AWG
Gray 20AWG
Purple/Black 20AWG
Gray/Black 20AWG
Green 20AWG
White 20AWG
Green/Black 20AWG
White/Black 20AWG
Yellow 18AWG
Black 18AWG
Red 22AWG
Red/White 22AWG
Brown 22AWG
Pink/Silver 22AWG
Black 22AWG
Black/Silver 22AWG
Yellow 22AWG
Orange/Silver 22AWG
Yellow 18AWG
Red 18AWG
Black 18AWG
Remote Harness
12
11
10
9
7
8
6
5
4
3
2
1
HDMI Switcher
1
4
2
5
6
3
Key Harness
3
2
1
Direct Camera
6
5
4
3
2
1
Red/White 22AWG
Brown 22AWG
Black 20AWG
Red 20AWG
Yellow 20AWG
Brown 22AWG
Brown 22AWG
Black/Silver 22AWG
Orange/Silver 22AWG
Pink/Silver 22AWG
Black 22AWG
Black 22AWG
Red 22AWG
Blue 22AWG
Black 22AWG
White 22AWG
Cam Aux Data
17
18
15
16
13
14
12
11
10
9
8
576
4
3
1 2
Rear Camera
6
5
4
3
2
1
Alternate Power
3
2
1
Red 22AWG
Blue 22AWG
Black 22AWG
White 22AWG
White 22AWG
Blue 22AWG
Black 22AWG
Red 22AWG
Black 22AWG
Black 22AWG
White 22AWG
Green/White 22AWG
Red 22AWG
Black 22AWG
Yellow/Black 22AWG
Red 22AWG
Orange/White 22AWG
Orange 22AWG
Yellow 18AWG
Red 18AWG
Black 18AWG
Data SWC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
Audio Out
17
Wrangler Radio
1
2
13
3
14
15
4
16
5
17
6
7
18
19
8
9
20
10
21
22
11
12
Brown/Red 22AWG
Brown/Yellow 22AWG
Red/Brown 22AWG
Yellow/Brown 22AWG
Yellow/Black 22AWG
1
2
3
Yellow 18AWG
Brown/Red 22AWG
Brown/Yellow 22AWG
Gray 20AWG
Green 20AWG
Gray/Black 20AWG
Green/Black 20AWG
White 20AWG
Purple 20AWG
White/Black 20AWG
Purple/Black 20AWG
Black 18AWG
Red 22AWG
White 22AWG
Black 22AWG
Radio I/O
1 2
4
3
6
5
87
9 10
iDatalink
1
2
3
4
Speaker Harness
1
2
3
4
Speaker Harness
1
2
3
4
Orange 22AWG
White/Grey 22AWG
Orange/White 22AWG
Green/White 22AWG
Yellow/Blue 22AWG
Blue/White 22AWG
Blue 22AWG
White 22AWG
Black 22AWG
Red 22AWG
Purple 20AWG
Purple/Black 20AWG
Green 20AWG
Green/Black 20AWG
Gray 20AWG
Gray/Black 20AWG
White 20AWG
White/Black 20AWG
Power/ACC
3
2
1
Audio In
1 2
43
5
6
87
9 10
Wrangler Harness
1
6
2
7
8
3
4
9
5
10
Yellow 18AWG
Red 18AWG
Black 18AWG
White/Red 22AWG
White/Brown 22AWG
Grey/Red 22AWG
White/Brown 22AWG
White/Red 22AWG
White/Brown 22AWG
Gray/Red 22AWG
Page 18
Connection Of HCE-TCAM1-WRA
To HCE-TCAM1-WRA
This connection goes to
the direct video input of
the head unit through the
adapter. If you do not make
this connection there will be
no video to your X209-WRA-OR
Jeep Wrangler
WRANGLER 18/22
Direct Camera Adapter
X209D OR Source Unit
ANTENNA
Direct Camera Input
CAN I/F
GPS
SXM/DAB
PRE OUT
USB
EXT. KEY
To HCE-TCAM1-WRA
This connection goes to
the camera connector on
the main harness. This
handles the power, ground,
reverse light, and illumination
connections.
Rear View Camera
WARNING!
The use of this connection
is intended for Alpine
HCE-TCAM1-WRA rear
view camera ONLY.
Connection Of An External Amplifier
X209-WRA OR - Source Unit
USB
CAN I/F
GPS
SXM/DAB
PRE OUT
ANTENNA
HDMI IN HDMI OUT
W.REMOTE POWER
(Blue/White)
Rear View Camera
6-pin Black Connector
REMOTE
Main Harness
X209D OR DVD/Display
RCA Extension Cable (sold separately)
Remote Turn-On Lead (Blue/White)
Subwoofer RCA Connectors
Front Output RCA Connectors
Rear Output RCA Connectors
REMOTE ON
(Blue/White)
REMOTE ON
(Blue/White)
SUBW
FRONT OUT
REAR OUT
(Red)
(White)
(Red)
(White)
(Red)
(White)
Amplier for subwoofer
(sold separately)
To subwoofer input terminal
To front input terminal
Amplier 4 ch
(sold separately)
To rear input terminal
Subwoofer
Front speaker
Rear speaker
Page 19
Connection Of KAC-001
Jeep Wrangler
WRANGLER 19/22
KAC-001 Side View
POWER RESET HEADUNIT CAN OUTPUT UPDATE
Reset
Button
Power Harness
(3-pin White)
BATT* (Yellow)
ACC (Red)
GND (Black)
*Fuse Rating: 7A
Connect to IDATALINK I/F
cable from head unit. This is
the 4 pin data connector
shown on page 12 in the
installation diagram that
comes directly off of the
main harness
3 Pin
Black
Interface Cable (4-pin)
Interface Harness (4-pin White)
(included with ADS module)
8ch Output Harness
Maestro Module Side View
4 Pin
10 Pin
Blue
Green
USB port
(Firmware
updates only)
Output 1 (Purple)
Output 2 (White/Red)
Output 3 (Brown)
(24-pin White)
Output 4 (Blue)
Output 5 (Green)
Output 6 (Pink)
Output 7 (White)
Output 8 (Gray)
Connect to Relay/output to
accessories (Sold separately)
To 4 Pin Black Data
4 Pin
3 Pin
Black Data
Black
Main Harness
To Head Unit
Not
Used
Page 20
Steering Wheel Configuration
Factory Option
Phone
Voice
VR
Jeep Wrangler
WRANGLER 20/22
Seek Up
Preset Up
Seek Down
Volume Up
Source
Volume Down
Button Press Once Press And Hold
Volume Up Volume + None
Volume Down Volume - None
Seek Up Track + None
Seek Down Track - None
Source Source/Camera View None
Next Preset Preset & Folder + Preset & Folder -
Voice Voice Or Siri None
Phone Answer Call Hang Up & Reject Call
Page 21
Jeep Wrangler
WRANGLER 21/22
Set Up Guide
1 Turn the vehicle’s Ignition switch to ACC.
2 Turn ON the X209-WRA-OR by pressing any key.
3 Select the user language and press OK.
4 Engage and release the parking brake twice.
5 If a camera is present, turn it ON in the system menu. (MENU/SETUP/SYSTEM/CAMERA/CAMERA SELECT).
6 AUDIO MUTE ON REVERSE- By default, when the vehicle is shifted into reverse the AUDIO will MUTE. If this
feature is not desired turn it off in the AUDIO MENU (MENU/SETUP/SOUND/MUTE WHILE BACKING UP).
7 When the KCX-630HD (HDMI SELECTOR) is present be sure to turn it ON in the SETUP MENU. (MENU/
SYSTEM/EXTERNAL ACCESSORIES/HDMI SELECTOR).
8 Set the DVD player. (MENU/SETUP/SOURCE/HDMI).
9 When the KAC-001 (External Accessory Control Module) is present be sure to turn it ON in the SETUP MENU.
(MENU/SYSTEM/EXTERNAL ACCESSORIES/EXTERNAL ACCESSORY CTLR).
10 Vehicle information- Set the desired gauge information. (MENU/VEHICLE INFO/GAUGES/CAR SETTINGS).
Troubleshooting Guide
Symptom Possible Cause Remedy
1
iPhone not working with
HDMI.
2
Android phone is not working
with HDMI.
3
iDatalink website says serial
number is invalid.
4 No output from RCA’s
Not using Apple HDMI to Lightning
adapter.
Didn’t plug USB power into a 2A
source.
Using incorrect HDMI adapter.
Miracast adapter isn’t plugged into
a 2A source.
Miracast adapter has resolution
settings that are too high.
Incorrect serial number is being
used.
Serial number may not be in
iDatalink database.
Maestro module is flashed for
amplified system.
Purchase the HDMI to Lightning adapter
directly from Apple. Not all 3rd party
adapters work the same.
Do not plug into the USB from the Alpine
head unit. A third party USB adapter will
need to be used that is 2A.
If the phone has the feature to use an HDMI
adapter it must be the one purchased from
the manufacturer of the phone, not a third
party adapter.
Do not plug into the USB from the Alpine
head unit. A third party USB adapter will
need to be used that is 2A.
Plug the adapter into another monitor (for
example a television in the home) and reduce
the resolution settings.
In the X209-WRA-OR settings confirm the
serial number. MENU/SETUP/GENERAL/
ABOUT.
Call ADS at 1-866-427-2999 and verify.
Re-flash module for non-amplified system.
Page 22
Troubleshooting Guide Continued
Symptom Possible Cause Remedy
5
Headunit will not turn on.
6
Cannot enter SETTINGS
MENU.
7
Cannot control the DVD
Player properly.
Sound mutes when vehicle is
8
shifted into reverse.
Only the front speakers are on
9
for SXM Radio.
The vehicle is incorrectly
10
positioned on the Navigation
display.
CarPlay, Android Auto, or
11
off-road navigation map
positioning issues.
CarPlay, Android Auto, or
off-road navigation vehicle
12
position icon heading in
wrong direction
Jeep Wrangler
WRANGLER 22/22
Incorrect serial number was used
when flashing maestro.
4 pin Maestro data cable is
disconnected or damaged.
OBD2 cable is not plugged in. Connect OBD2 connector to the OBD2 port.
Monitor, key-harness or main
harness are not connected.
Vehicle is in motion or parking
brake is not engaged.
DVD has not been set on the
SETUP menu.
HDMI box has not been set on the
SETUP menu.
Mute on reverse is turned on in the
SOUND menu.
SXM Tuner has not been activated. Activate SXM Tuner.
Poor GPS signal.
GPS antenna is positioned
incorrectly.
Reverse Signal is not connected or
not reliable.
Flash Maestro with correct serial number.
Check for proper connection or
disconnected pins.
Check for proper connection or
disconnected pins.
With vehicle in (P)PARK engage the parking
brake. Release the parking brake and
engage the parking brake a second time, as
shown in the Setup Guide on page 20.
Ensure DVD is ON in HDMI SETUP menu.
Ensure DVD is ON in HDMI SETUP menu and
remote loop was cut on the wire harness.
Change Mute on reverse to off.
Ensure the recommeded GPS antenna route
was used. See page 7.
GPS antenna is obstructed and doesn’t have
line of sight to the sky. Perform a factory
reset. The unit will automatically recalibrate.
Ensure that Reverse wire is connected. Also
ensure that no 3rd party interface module(s)
interfere with the Reverse Signal. The head
unit uses the Reverse Signal to achieve
optimal positioning performance.
iPhone or Android phone is
not recognized
13
when connected to the
USB cable.
Volume controls on bezel and
14
steering wheel controls do not
work.
Disc mechanism is not
15
ejecting.
Loose or disconnected USB cable.
Non-compatible cable.
Dirty charging port on phone. Clean charging port.
The setting for External Processor
was turned on.
The wires from the remote harness
were pulled out during installation.
Check the USB connection behind
the headunit.
Use the cable supplied with the
iPhone or Android phone. Third party
adapters and long extensions may not work.
Only use USB extension that came with the
head unit.
That setting should only be checked when
using an external sound processor. When
there isn’t one being used in the audio
system it needs to be in the default setting
of off. MENU/SETUP/SYSTEM/EXTERNAL
ACCESSORIES/EXTERNAL AUDIO
PROCESSOR/OFF
Make sure the Red/White and Brown wires
are pinned correctly as shown on page 17 of
this installation manual.
Loading...