Page 1
Connectivity Layout
Steering wheel remote control
interface installation kit for
IVECO
Model: Daily VI open dash with SWRC
Year: 2014 > 2019
Kit content: SWRC interface
wiring harness
All installation work must be performed by a qualified professional installer only.
The manufacturer / dealer is not liable for any kind of incidental or indirect damages.
06/2020 ALL RIGHTS RESERVED. Technical changes possible. No liability for misprints.
8
1
Page 2
Content and wiring harness connections
INSTALL THIS HARNESS INSTEAD OF THE POWER CABLE
CONTAINED IN THE X903D-ID, KIT-7ID AND KIT-F9ID KITS
FOLLOWING THE PROCEDURES BELOW:
REMOVE THE INTERFACE WITH THE LABEL SHOWN BELOW
FROM THE KITS: X903D-ID, KIT-7ID AND KIT-F9ID:
AND CONNECT IT TO POINT (4) SEE THE NEXT PAGE.
2
8
10
9
7
4
6
11
3
1 - to RADIO connector
2 - to RADIO connector
3 - to CAMERA INPUT
4 - to X903D-ID / KIT-7ID / KIT-F9ID interface
5 - to LIN BUS connector cable:
to key harness contained in X903D-ID,
to LIN cable contained in KIT-7ID & KIT-F9ID
6 - AUX input
7 - connect these 3 cables to the 3 voltage SWRC cable in the vehicle:
Pink with Pink cable
Pink/Black with Pink/Black cable
Brown with Brown cable
8 - to SERVICES provided by the vehicle:
Yellow - to vehicle SPEED pulse (MUST be connected to vehicle)
White - to vehicle REVERSE signal (MUST be connected to vehicle)
9 - CAMERA control / REMOTE output
10 - POWER ANTENNA output
11 - to CAR connector
12 - external power access
12
2
1
5
3
Page 3
1. Cable Connections 2.1 Connecting Reverse Signal (White cable (point 8 / page3))
Connect the harness as indicated in the installation manual
(IM_X903D-ID_EN) of X903D-ID (page 26-27) to vehicle and as
indicated on the last page (8). Please also note the points on the
following pages of these instructions.
Body Computer/Fuse Box
Left Connector F (Green or Black):
Pin 4 = Reverse Light
Remove the cover of the Green or Black plug. The Grey/Green or
White/Green cable carries the reverse signal. Remove the terminal from
the connector housing. Connect the White cable (point 8 / page 3) from
the wiring harness to the Grey/Green or White/Green cable from the
vehicle connector.
2.2 Connecting Speed Signal (Yellow cable (point 8 / page3))
2. Speed and Reverse Cable Connections (point 8 / page 3)
Connect the two SERVICES cables.
→ Yellow - to vehicle SPEED pulse (MUST be connected to vehicle)
→ White - to vehicle REVERSE signal (MUST be connected to vehicle)
Body Computer/Fuse Box
Right Connector D (Black):
Pin 56 = Speed Signal
Remove the cover of the Black plug.
The Orange cable, if proven otherwise, installing a PIN, carries the speed
signal. Remove the terminal from the connector housing.
Connect the White cable (point 8 / page 3) from the wiring harness to
the Grey/Green or White/Green cable from the vehicle connector.
4
5
Page 4
3. Three Voltage SWRC Cable Connections
4. LIN BUS Cable Connection (White and Brown cable (point 5 / page3))
There are a few vehicles that control the steering wheel remote control
via three voltages cables. The original delivery status of the X903D-ID
does not work for these vehicles, because the original connection
wiring harness does not have a connection for these 3 voltage cables.
By connecting these 3 cables, a transmission to the functionality of the
steering wheel remote control is done.
Connect the three voltage cables (point 7 / page 3) for SWRC.
→ Pink with Pink cable in vehicle
→ Pink/Black with Pink/Black cable in vehicle
→ Brown with Brown cable in vehicle
You can find these 3 cables in the radio slot, close to the original radio
connection wiring harness.
Connect the two LIN BUS connector cables:
→ to key harness contained in X903D-ID or
→ to LIN cable contained in KIT-7ID & KIT-F9ID
5. Interface Connection (point 4 / page3)
Connect the interface contained in X903D-ID, KIT-7ID or KIT-F9ID to the
wiring harness (point 4 /page 3).
6 7
Loading...