Allstar Products Group 9921T, 9931TK, 8832T, 9931MT, 8833T User Manual

...

Operational Check

After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 45 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. However, environmental conditions and the location of the transmitter and receiver will affect distance.

•

If the transmitter doesn’t activate the operator check the coding on both the transmitter and receiver. The code setting must match exactly .

•

If the distance is inadequate check the battery and replace if necessary.

•

To maximize the operating distance move the transmitter to different locations in the car until a satisfactory distance is achieved. Vanity mirrors on sun visors will affect performance.

Manufacturer’s Limited Warranty

Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one (1) year from the date of purchase. To obtain service, contact your dealer.

To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Allstar before returning the goods. The goods must be returned with complete identification, with copy of proof-of-purchase, freight prepaid and in accordance with Allstar’s instructions or they will not be accepted. In no event will Allstar be responsible for goods returned without proper authorization or identification.

Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are confirmed to be defective and covered by this limited warranty, will be repaired or replaced at Allstar’s sole option, at no cost and returned pre-paid. Defective parts will be repaired or replaced with new or factory rebuilt parts at Allstar’s sole option.

This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and necessary maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or replacement batteries.

These warranties are in lieu of all other warranties, either expressed or implied. All implied warranties of merchantability and/or fitness for a particular purpose are hereby disclaimed and excluded. Under no circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection with the use or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product.

This warranty gives you specific legal rights. Warranty effective after July 24, 2002.

•

If the receiver is in the proximity of a metal beam or other obstruction it may be necessary to relocate the receiver to increase the operating range.

•

If multiple receivers are mounted closer than 15 feet, blocking and interference may occur. Move the receivers further apart.

•

If system does not work at any distance, check that the receiver terminals are connected to the proper operator terminals.

•

If the HomeLink® transmitter does not activate the operator or distance is inadequate,verify proper operation using the hand-held transmitter. Contact your HomeLink® system provider for help with configuring the HomeLink® transmitter and to resolve distance problems when using the HomeLink® system.

Classic Quik-Code Transmitter

Installation Instructions

Replacement for Models:

•9921T •9931T •8822T •8832T

•8833T •9921MT •9931MT •9921TK

•9931TK •8832TK •9931TK6

Product Features

The Classic Quik Code Transmitter makes it possible to operate a single or group of remotely controlled devices such as a garage door opener, with a single transmitter.

Follow these simple instructions.

Programming the Classic is done by simply:

1. Put the transmitter in program mode.

2. Select the button you wish to use.

3. Enter your 9 digit code.

Please read the instructions completely before starting.

Further instructions are available at www.allstarcorp.com

INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS

Select the block of switches below that best matches the one in the

transmitter or receiver that you are replacing.

*The grids display an EXAMPLE

9 switches w/ + 0 -

1 2 3 4 5 6 7 8 9

using the code shown on the switches to the left.

- - 0 0 + + - 0 +

9 switches w/ On & Off

turn page

1 2 3 4 5 6 7 8 9

Go to Step 1...

- - + + - - + + -

1 2 3 4 5 6 7 8 9

- - + + - - + + -

8 switches w/ + 0 -

1 2 3 4 5 6 7 8 9

turn page

Go to

Step 1a

WARNING

Unexpected door operations can cause personal injury or property damage.

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

- - 0 0 + + - 0

turn page

WARNING

Go to Step 1...

Disconnect power to operator before any installation or repair. Follow all

instructions provided by the manufacturer of your operator.

Allsta r Rad io Controls are compatib le wit h HomeLink®.

Homelink® is a registered trade mark of Johnson Controls, Inc.

The table has a row for each one of the three buttons since it is possible to set a unique code for each

NOTE:

button. Write the code that you matched from your transmitter or receiver in the grids below.

+ / On

BUTTON

Zero

BUTTON

- / Off

BUTTON

1 2 3 4 5 6 7 8 9

- PUT THE TRANSMITTER IN PROGRAM MODE -

First, press and hold the +

button. The Red LED will turn on. Next, while continuing to hold the + button,

press and hold the

button. Continue to hold both buttons until the LED starts to blink (approximately 5 seconds). Release

both buttons while

the LED is blinking.

The LED will blink two times and then remain on to confirm you are in programming mode.

Go to Step 2

*If the LED goes out, start over.

1a.

button. The Red LED will turn on. Next, while continuing to hold the press and hold the + button. Continue

to hold both buttons until the LED starts to blink (approximately 5 seconds). Release

both buttons while

The LED will blink two times and then remain on to confirm you are in programming mode.

First, press and hold the

the LED is blinking

Go to Step 2

*If the LED goes out, start over.

button,

INSTRUCTIONS FOR USE WITH AN ALLSTAR

SMART RECEIVER

When using the Allstar Classic with a Smart Receiver there is no need to

match a switch setting.

Simply make up your own unique code, enter it in the grid on page 2

When the transmitter is programmed, follow the instructions for teaching

If you want to program all the buttons you can Express Code them by

Note:

selecting the + button in Step 2 and ending the 9 position code in Step 3 with a +. This will code all three buttons in one programming step.

and follow the instructions starting with Step 1.

the receiver the transmitter code.

WARNING

- SELECT THE BUTTON YOU WISH TO USE

button you wish to use.

switches press the you’d like to use).

then remain on.

While the LED is on, press the

(If your block has 8

button, if not, press any button

The LED will blink off once and

Go to Step 3...

- ENTER YOUR 9 DIGIT CODE

Enter the 9-digit code from the

table pressing the buttons that correspond with the grid above.

use the

button in the 9th position)

After the 9-digit code is entered, the

(If your block has 8 switches

Go to Step 4...

LED will blink twice to confirm a valid code and remain off.

Repeat the procedure for the remaining buttons.

IMPORTANT

The SAME CODE must be set

on both the transmitter and

receiver. The controls will not

function if the codes are

mismatched

Keep transmitters and remote controls

out of the reach of children.

Do not let children play with or use the

transmitter or remote controls.

Unexpected door operations can cause

personal injury or property damage.

Do not place transmitter where the buttons

can be accidentally or unintentionally

activated.

Installing the Transmitter

The transmitter is supplied with a metal clip which may be used to attach the unit to a sun visor. If the clip is used, slide it into the recess provided on the back of the transmitter case until the snaps on the case fit around the clip. If the transmitter is installed in a pocket in your car, follow all the manufacturer’s instructions.

Improper transmitter installation or use may cause intermittent operation which can

result in unexpected door operations.

Battery Replacement

The MVP Quik-Code transmitter is provided with two factory installed 3-volt batteries which should be replaced after two years of normal use. The transmitter code is retained in permanent memory and will not be lost during battery replacement. To replace the batteries, remove the back of the case with a small screwdriver. Carefully slip the batteries out of the holders and replace with fresh CR2032 3-volt batteries. The “+” on the batteries must point away from the circuit board. Replace the back of the cover and resume normal use.

Allstar Products Group 9921T, 9931TK, 8832T, 9931MT, 8833T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual