Allied Telesis Rapier G6F-MT-RJ, Rapier G6F-LX, Rapier G6F-SC, Rapier G6F-SX, Rapier 8 Quick Install Manual

RAPIER SWITCH

QUICK INSTALL GUIDE

Rapier Switch Quick Install Guide
Document Number C613-04017-01 REV F.

Copyright © 1999-2003 Allied Telesyn International, Corp.
19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA.

All rights reserved. No part of this publication may be reproduced without prior written
permission from Allied Telesyn.

Allied Telesyn International, Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall Allied
Telesyn be liable for any incidental, special, indirect, or consequential damages
whatsoever, including but not limited to lost profits, arising out of or related to this
manual or the information contained herein, even if Allied Telesyn has been advised of,
known, or should have known, the possibility of such damages.

All trademarks are the property of their respective owners.

This implementation of IPsec has been certified to meet ICSA Labs
IPsec security standards. For more information see

http://www.icsalabs.com

Quick Install Guide 3

C613-04017-01 REV F

Models Covered By This Guide

This Quick Install Guide includes information on the following models:

■ Rapier G6

■ Rapier G6F-LX/SC

■ Rapier G6F-SX/SC

■ Rapier G6F-SX/MT-RJ

■ Rapier 8/8MT

■ Rapier 8/8SC

■ Rapier 16F-FX/MT

■ Rapier 16Fi-FX/MT

■ Rapier 16F-FX/SC

■ Rapier 16Fi-FX/SC

■ Rapier 24

■ Rapier 24i

■ Rapier 48

■ Rapier 48i

Quick Install Guide updates can be downloaded from
www.alliedtelesyn.co.nz/support/rapier/.

Rapier Switch

Safety and Statutory Information

Quick Install Guide

Hardware Reference

Software Reference

Network Service Module

NSM Quick Install Guide

NSM Hardware Reference

Port Interface Card

PIC Quick Install Guide

PIC Hardware Reference

General Customer Support

Visit www.alliedtelesyn.co.nz for
the latest documentation, FAQ,
and support information

Uplink Module

Uplink Module Quick Install Guide

Uplink Module Hardware Reference

Printed Acrobat PDF

Website

Documentation Roadmap

User Guide

4 Rapier Switch

C613-04017-01 REV F

Package Contents

The following items are included with each Rapier Switch. Contact your sales
representative if any items are damaged or missing.

■ One Rapier Switch.

■ One AC power cord (AC models only).

■ One serial cable for connecting the switch to a terminal or PC.

■ One 19 inch rack-mount kit.

■ One Rapier Switch Quick Install Guide.

■ One Safety and Statutory Information booklet.

■ One Rapier Switch Documentation and Tools CD-ROM (which includes

the complete Rapier Document Set and utilities).

■ One warranty card.

Selecting a Site

The switch can be installed in a standard 19-inch rack or on a level surface such
as a desktop or bench. When installing the switch, choose a site that:

■ Allows adequate airflow around the switch and its vents.

■ Is free of dust and moisture.

■ Will maintain an ambient temperature range of 0 to 40º C (32 to 104º F) and

a humidity range of 5 to 95% non-condensing.

■ Has a reliable and earthed (grounded) power supply circuit, preferably

dedicated and filtered.

■ Does not expose cabling to sources of electrical noise, such as radios,

transmitters, broadband amplifiers, power lines, electric motors, and
fluorescent fixtures.

■ Allows easy access to the switch’s power and cable connections.

■ Will allow all related network devices to be connected to the switch

without exceeding maximum cable length limitations. See the Rapier Switch
Hardware Reference for cable length specifications.

Quick Install Guide 5

C613-04017-01 REV F

Installing the Switch

All AC and DC versions of this equipment must be earthed.

Follow these steps to install the switch:

1. Before installing the switch, read the safety information

For safety information, see the Safety and Statutory Information booklet. A
copy of this booklet is supplied with each switch, and can also be found on
the Documentation and Tools CD-ROM or at www.alliedtelesyn.co.nz/
support/rapier/.

2. Gather the tools and equipment you will need

If installing a DC version of the switch, you will need a DC power source,
DC supply cable, and wire strippers (see step 8).

If the switch is to be connected to a redundant power supply, you will need
a redundant power supply unit and cable (see step 10).

3. Choose a suitable site for the switch

Either a flat surface or 19 inch rack.

4. Unpack the switch

Verify the package contents. If any items are damaged or missing, contact
your sales representative.

5. Install expansion options

If you purchased optional Uplink Modules, a Network Service Module
(NSM), or Port Interface Cards (PICs), install them now by following their
individual installation guides. These guides can be found on the
Documentation and Tools CD-ROM.

6. Place the switch in its operating location

If installing the switch in a rack:

• Remove the rubber feet.

• Attach the rack-mounting brackets.

• Mount the switch in the rack.

7. Apply AC power to the switch (for AC models)

Plug the power cord into the AC power connector on the switch’s rear
panel. The Fault LED should flash for approximately 10 seconds as the
switch runs internal tests. If the LED continues to flash or remains lit, refer
to the Rapier Switch Hardware Reference for troubleshooting information.

6 Rapier Switch

C613-04017-01 REV F

Figure 1: Rapier front panel and rear panel with AC power inlet.

8. Apply DC power to the switch (for DC models)

Read the Safety and Statutory Information booklet before connecting a DC
power supply. A copy of this booklet is included with each switch. It is also
included on the Documentation and Tools CD-ROM, or can be
downloaded from www.alliedtelesyn.co.nz/support/rapier/.

Only trained and qualified personnel should connect a DC power supply. Due
to exposed terminals, DC powered switches should only be installed in
Restricted Access Areas.

DC supply cable specifications:

• Number of wires (cores): 3

• Minimum size: 2.1mm

2

(14 AWG)

• Minimum cable rating: 600V, 90 degrees Celsius

DC power supply specifications:

• 48 VDC (39-60 VDC is acceptable)

• Either positive grounded or negative grounded

Circuit protection:

• Use a 10 Amp circuit breaker

To connect the DC supply:

a) Ensure the supply cable is not live

b) Strip the supply cable wires to expose 8mm (0.31 in.) of bare conductor

c) At the switch, connect the ground wire to the ground terminal (The

terminals can be identified by the diagram on the switch’s rear panel,
see Figure 2). Tighten the terminal to between 0.6 and 0.8 Nm (0.041 to

0.055 pound-force per foot)

STATUS

RESET

FAULT

PWR

RPS

1234567891011121314151617181920212223

24

10BASE-T / 100BASE-TX

1X 3X 5X 7X

2X 4X 6X 8X

9X 11X 13X 15X

10X 12X 14X 16X

17X 19X 21X 23X

18X 20X 22X 24X

25

26

RS-232

TERMINAL PORT

100M LINK / ACTIVITY 10M LINK / ACTIVITY

HALF DUP/

COL

FULL DUP

PORT ACTIVITY

L/A

L/A

D/C

D/C

L/A

D/C

ASYN0

Layer 3 Fast Ethernet Switch

NSM 0

Hot Swap

In Use

Swap

Front panel

Uplink Module Bays

10/100 BASE Ports

Port LEDs System

LEDs

RS-232 Terminal Port

Rear panel

100-240 VAC

Power Inlet

RPS Inlet for

AT-PWR8000

NSM BAY NSM Hot Swap

Button and LEDs

Quick Install Guide 7

C613-04017-01 REV F

d) At the switch, connect the positive feed to the + (positive) terminal and

the negative feed to the - (negative) terminal. Tighten the terminals to
between 0.6 and 0.8 Nm (0.041 to 0.055 pound-force per foot)

e) Ensure there are no exposed conductor strands

f) Secure the supply cable (to the rack framework or similar object) so the

connections are isolated from any forces applied to the cable

g) Ensure the circuit breaker is in the Off position

h) Connect the supply-cable wires to the circuit breaker

i) Energise the circuit breaker

Figure 2: DC Power inlet terminals on a Rapier 24.

The Fault LED should flash for approximately 10 seconds as the switch
runs internal tests. If the LED continues to flash or remains lit, refer to the
Rapier Switch Hardware Reference for troubleshooting information.

9. Check that the Power LED on the switch’s front panel lights green

If the LED fails to light, refer to the Rapier Switch Hardware Reference for
troubleshooting information.

10. Connect the Redundant Power Supply (Optional)

AC models of Rapier Switches have a Redundant Power Supply (RPS)
connector on their rear panel.

The Switch is designed to operate with the AT-RPS8000 RPS, which can be
purchased separately. Contact your authorised Allied Telesyn distributer
or reseller for more information.

11. Connect the data cables

Make sure each cable connection is secure. The switch will now perform
basic Layer 2 switching functions.

Configuring the Switch

Some configuration is necessary if you wish to enable the switch’s advanced
switching capabilities. The switch can be configured via the Command Line
Interface (CLI) or Graphical User Interface (GUI).

Using the CLI to configure a switch

1. Connect a terminal or PC to the Terminal Port (ASYN0)

Using the supplied RS-232 DB9 straight-through cable, connect your
terminal or PC to the RS-232 Terminal Port on the switch’s front panel.

NSM 0

Hot Swap

In Use

Swap

38-75VDC , 2A

FOR CENTRALIZED DC
POWER CONNECTION,

INSTALL ONLY IN A
RESTRICTED AREA

DC Power inlet

DC INPUT

8 Rapier Switch

C613-04017-01 REV F

2. Set the communication parameters

Set the communication parameters on your terminal or terminal emulation
program to:

• Baud rate: 9600

• Data bits: 8

•Parity: None

•Stop bits: 1

• Flow control: Hardware

3. Log in

After the switch has booted, the log in prompt appears. If the log in prompt
doesn’t appear, press [Enter] two or three times.

When the switch boots for the first time it automatically creates an account
with manager privileges. The account has the log in name “manager” and
the password is “friend”.

At the log in prompt, enter the log in name and password.

Login: manager

Password: friend

The switch’s command prompt appears and you can now configure the
switch using the command line interface.

Change the password as soon as possible. Leaving the manager account with
the default password is a serious security risk. Make sure you remember the
new password as there is no way to retrieve it if it is lost.

Use the following command to change the account password:

set password

4. Load command line interface help files

To access CLI help, enter:

set help=help-filename

where help-filename is the name of a help file stored in flash.

To see a list of files stored in flash, enter:

show file

Help files have an HLP extension.

To display a list of help topics, enter:

help

To display help on a specific topic, enter:

help topic

Alternatively, type a question mark (?) at the end of a partially completed
command to see a list of valid options.

See the Rapier Switch Software Reference for more information on
configuring the switch.

Quick Install Guide 9

C613-04017-01 REV F

Using the GUI to configure a switch

The GUI can be accessed through the switch’s default VLAN (VLAN1). To
set-up the GUI the first time it is used, you must first access the CLI.

1. Access the CLI

Follow the instructions in the previous section: “Using the CLI to configure
a switch”.

2. Enable IP

At the CLI, enter the command:

ENABLE IP

3. Assign an IP address to VLAN1

Assign the VLAN1 interface an IP address in the required subnet, using the
command:

ADD IP INTERFACE=vlan1 IP=ipaddress MASK=mask

4. Define a route (if required)

If the PC from which you will access the GUI is on a different subnet to the
switch, add a route from the PC to the switch. Enter:

ADD IP ROUTE=PC-ipaddress INTERFACE=vlan1

NEXTHOP=switch-ipaddress

5. Connect the PC to a switch port

The PC can be connected directly or through a LAN.

The PC should be running Internet Explorer 5.x or Netscape 6.2.2, with
JavaScript enabled. Internet Explorer can be found on the Documentation
and Tools CD-ROM that is bundled with your switch.

If you access the Internet through a proxy server, set your browser to
bypass the proxy for the IP address you just assigned to the VLAN1
interface.

Point your web browser at the IP address of the VLAN interface.

6. Log in

At the log in prompt, enter the log in name and password.

User Name: manager

Password: friend

The system status page appears and you can now use the GUI to configure
the switch.

To ensure configuration settings are saved correctly, use the GUI pages’ menus and
buttons to navigate, not your browser’s buttons.

As a security precaution, change the password as soon as possible.

To change the password, select Management > Users from the sidebar
menu. Select the Manager account and click Modify.

7. To access context-sensitive help

Click on the Help button [Help] on each page.

10 Rapier Switch

C613-04017-01 REV F

System LEDs

System LEDs on its front panel indicate the switch’s operational status.

1. DC models of the Rapier Switch do not have an RPS connector and the RPS LED will not function.

2. Not included on the Rapier 48, G6, G6F-SX/SC, G6F-LX/SC, or G6F-SX/MT-RJ.

3. Hot swapping is supported by Software Release 2.3.1 or later. AT-AR021 (S) BRI-S/T, AT-AR021 (U)
BRI-U, and AT-AR023 SYN PICs can be hot swapped.

The Rapier Switch Hardware Reference has further troubleshooting information,
including information on Switch Port and Uplink Module LEDs.

System LEDs

LED State Function

Power Green The switch is receiving power and the voltage

is within the acceptable range

Fault Red The switch or management software is

malfunctioning

1 flash A switch fan has failed. (The LEDs will not

indicate an RPS fan failure.)

3 flashes If an RPS is connected, the switch’s PSU (Power

Supply Unit) has failed

4 flashes If RPS monitoring is enabled, the RPS PSU has

failed

5 flashes If RPS monitoring is enabled, an RPS is not

connected or is not operational

RPS

1

(Redundant

Power Supply)

Green An RPS is connected to the switch

In use2 (Rear panel)

Green An NSM is installed, is receiving power, and is

operational. The NSM and its PICs are not
ready to be hot swapped

Off No NSM is installed, or the NSM is not installed

correctly (the switch unit has not recognised
the NSM)

Swap2 (Rear panel)

Green The NSM and its PICs are ready to be hot

swapped

Off The Hot Swap button must be pressed before

the NSM or PICs can be hot swapped, or the
software release does not support hot
swapping

3

Quick Install Guide 11

C613-04017-01 REV F

Documentation and Tools CD-ROM

The Documentation and Tools CD-ROM bundled with each Rapier Switch
contains the complete Documentation Set for your switch and its expansion
options, as well as tools for managing the switch. This includes:

■ The Rapier Switch Safety booklet, which provides safety and statutory

information for the Rapier Switch and its expansion options.

■ The Rapier Switch Hardware Reference, which provides detailed information

on the hardware features of Rapier Switches.

■ This Quick Install guide.

■ The Rapier Switch Software Reference, which provides detailed information

on configuring the switch and its software.

■ The Rapier Switch User Guide, which provides an introduction to the

switch’s Graphical User Interface and its Layer 2 switching features.

■ The Network Service Module Quick Install Guide, which outlines the

procedure for installing an NSM; and the Network Service Module Hardware
Reference, which provides detailed information on NSMs.

■ The Port Interface Card Quick Install Guide, which outlines the procedure for

installing PICs; and the Port Interface Card Hardware Reference, which
provides detailed information on PICs.

■ The Uplink Module Quick Install Guide, which outlines the procedure for

installing an Uplink Module; and the Uplink Module Hardware Reference,
which provides detailed information on Uplink Modules.

■ AT-TFTP Server for Windows, for downloading software releases.

■ Adobe Acrobat Reader, for viewing online documentation.

■ Microsoft Internet Explorer.