Allied Telesis AT-SBx3106WMB User Manual
AT-SBx3106WMB
Wall Mounting Brackets for the
AT-SBx3106 Access Edge Chassis Switch
Installation Guide
613-001941 Rev. A
Copyright 2014 Allied Telesis, Inc.
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis,
Inc.
Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names,
company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective
owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document
without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied
Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited
to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has
been advised of, known, or should have known, the possibility of such damages.
Contents
Preface ..............................................................................................................................................................7
Safety Symbols Used in this Document .............................................................................................................8
Contacting Allied Telesis....................................................................................................................................9
Installation Instructions ................................................................................................................................11
AT-SBx3106 Chassis and AT-SBx3106WMB Brackets ...................................................................................12
Required Tools.................................................................................................................................................13
Concrete Wall.............................................................................................................................................13
Wallboard...................................................................................................................................................13
Selecting a Wall Location .................................................................................................................................14
Minimum Dimensions of the Reserved Wall Area......................................................................................14
Wallboard Requirements............................................................................................................................16
General Wall Requirements....... ................................................................................................................18
Reviewing Safety Precautions..........................................................................................................................20
Checking the Components of the AT-SBx3106WMB Brackets........................................................................25
Marking the Wall Locations for the Screw Holes..............................................................................................26
Installing the Screws in the Wall.......................................................................................................................30
Concrete Wall.............................................................................................................................................30
Wallboard...................................................................................................................................................31
Installing the Brackets on the Chassis..............................................................................................................32
Installing the Chassis on the Wall.....................................................................................................................35
Installing the Vent Covers.................................................................................................................................39
3
Contents
4
Figures
Figure 1: AT-SBx3106 Chassis Switch with the AT-SBx3106WMB Wall Mounting Brackets ......................... 12
Figure 2: Minimum Area Dimensions When the Chassis has AC Power Supplies . ... ... ... .... ... ... ... ... .... ... ... ... .. 15
Figure 3: Minimum Area Dimensions When the Chassis has DC Power Supplies ......................................... 16
Figure 4: Brackets Aligned with Wallboard Studs............................................................................................ 17
Figure 5: Incorrect Installations on Wallboard ............................... ... ... ............................................................ 17
Figure 6: 100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle.................................................................. 19
Figure 7: Components of the AT-SBx3106WMB Wall Mounting Brackets...................................................... 25
Figure 8: Minimum Area Dimensions When Positioning the Bracket on the Wall ........................................... 26
Figure 9: Marking the Screw Holes for the Top Bracket.................................................................................. 27
Figure 10: Marking the Screw Holes for the Bottom Bracket........................................................................... 28
Figure 11: Screw Hole Measurements ............................................................................................................ 29
Figure 12: Installing the Screws .................................... ... ... ... .... ... ... ... ............................................................ 30
Figure 13: Shipping Brace............................................................................................................................... 32
Figure 14: Removing the Equipment Rack Brackets.............. .... ... ... ... .... ...................................... ... .... ... ........ 33
Figure 15: Turning the Chassis Upside Down on a Table............................................................................... 33
Figure 16: Attaching the Wall Mounting Brackets to the Chassis.................................................................... 34
Figure 17: Placing the Chassis on the Wall..................................................................................................... 35
Figure 18: Lowering the Chassis onto the Screws.......................................................................................... 36
Figure 19: Installing the Washers.................................................................................................................... 37
Figure 20: Tightening the Screws.................................................................................................................... 38
Figure 21: Installing the Top Vent Cover......................................................................................................... 39
Figure 22: Securing the Top Vent Cover......................................................................................................... 40
Figure 23: Installing the Bottom Vent Cover.................................................................................................... 41
Figure 24: Securing the Bottom Vent Cover.................................................................................................... 42
5
List of Figures
6
Preface
This guide contains instructions on how to install the AT-SBx3106 Chassis
on a wall with the AT-SBx3106WMB Wall Mounting Brackets. This preface
contains the following sections:
“Safety Symbols Used in this Document” on page 8
“Contacting Allied Telesis” on page 9
7
Preface
Note
Caution
Warning
Warning
Warning
Safety Symbols Used in this Document
This document uses the following conventions.
Notes provide additional information.
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
Warnings inform you that performing or omitting a specific action
may result in bodily injury.
Laser warnings inform you that an eye or skin hazard exists due to
the presence of a Class 1 laser device.
Fan warnings inform you of danger from hazardous moving fan
blades.
8
Contacting Allied Telesis
If you need assistance with this product, you may contact Allied Telesis
technical support by going to the Support & Services section of the Allied
Telesis web site at www.alliedtelesis.com/support. You can find links for
the following services on this page:
24/7 Online Support — Enter our interactive support center to
search for answers to your product questions in our knowledge
database, to check support tickets, to learn about RMAs, and to
contact Allied Telesis technical experts.
USA and EMEA phone support — Select the phone number that
best fits your location and customer type.
Hardware warranty information — Learn about Allied Telesis
warranties and register your product online.
Replacement Services — Submit a Return Merchandise
Authorization (RMA) request via our interactive support center.
AT-SBx3106WMB Wall Mounting Brackets Installation Guide
Documentation — View the most recent installation and user
guides, software release notes, white papers, and data sheets for
your products.
Software Downloads — Download the latest software releases for
your managed products.
For sales or corporate information, go to www.alliedtelesis.com/
purchase.
9
Preface
10
Installation Instructions
Warning
The following instructions explain how to install the AT-SBx3106 Chassis
on a wall with the AT-SBx3106WMB Wall Mounting Brackets. The
instructions contain the following sections:
“AT-SBx3106 Chassis and AT-SBx3106WMB Brackets” on page 12
“Required Tools” on page 13
“Selecting a Wall Location” on page 14
“Reviewing Safety Precautions” on page 20
“Checking the Components of the AT-SBx3106WMB Brackets” on
page 25
“Marking the Wall Locations for the Screw Holes” on page 26
“Installing the Screws in the Wall” on page 30
“Installing the Brackets on the Chassis” on page 32
“Installing the Chassis on the Wall” on page 35
“Installing the Vent Covers” on page 39
THE CHASSIS MUST BE INSTALLED BY A
QUALIFIED BUILDING CONTRACTOR. SERIOUS
INJURY OR DEATH MAY RESULT IF THE CHASSIS IS
NOT PROPERLY SECURED TO THE WALL.
11
Installation Instructions
Caution
Fan
Module
AT-SBx3106 Chassis and AT-SBx3106WMB Brackets
Figure 1 illustrates the AT-SBx3106 Chassis as it looks on the wall with
the AT-SBx3106WMB Wall Mounting Brackets.
The chassis must be installed on the wall in the orientation shown in
Figure 1. The fan module must be on top and the slot openings for
the line cards and power supplies must be on the right. The chassis
may experience inadequate ventilation and may overheat and fail if
it is installed on the wall in a different position than the one sho wn in
the figure.
12
Figure 1. AT-SBx3106 Chassis Switch with the AT-SBx3106WMB Wall
Mounting Brackets
AT-SBx3106WMB Wall Mounting Brackets Installation Guide
Caution
Required Tools
This section lists the tools necessary for installing the chassis on a wall
with the provided screws.
Concrete Wall The brackets come with hex-washer head lag screws for a concrete wall.
The screws are blue and have the following specifications:
Length: 1 3/4 in.
Diameter: 1/4 in.
Hex size: 5/16 in.
Quantity: 4
The following tools are required to install the chassis on a concrete wall
with the provided screws:
Hammer drill
3/16” carbide drill bit
5/16” socket or wrench
Wallboard The brackets come with hex-washer head lag screws for a wallboard wall.
The screws are silver and have the following specifications:
Length: 2 1/2 in.
Diameter: 1/4 in.
Hex size: 3/8 in.
Quantity: 4
The following tools are required to install the chassis on wallboard with the
provided screws:
3/8” socket or wrench
3/16” drill bit
Stud finder capable of identifying the middle of studs and hot
electrical wiring
The supplied screws may not be appropriate for all concrete or
wallboard walls. A qualified building contractor should determine the
appropriate hardware requirements for the wall prior to installing the
chassis.
13
Installation Instructions
Note
Selecting a Wall Location
The following sections contain information on how to select a wall location
for the chassis.
Minimum
Dimensions of the
Reserved Wall
Area
This section discusses the recommended minimum dimensions of the
reserved wall area for the chassis.
You might not be able to install or service the components of the
chassis if the reserved wall area is smaller than the recommended
minimum sizes given in this section.
The recommended minimum dimensions of the wall area for the unit
depend on whether the chassis has AC or DC power supplies. The
reserved wall area for a chassis that has AC power supplies has to be
larger than a chassis with DC power supplies, because AC power supplies
are powered on from the back panel of the chassis, whereas DC power
supplies are powered on from the front panel.
The minimum dimensions for the wall area for a chassis that has AC
power supplies are listed here:
Height: 84 cm (33 in.)
Width: 121 cm (48 in.)
The dimensions are illustrated in Figure 2 on page 15.
14
Loading...