Allegri 021052010FR001, 021052018FR001 User Manual
3x
3x
72
3x
串
3x
12x
6x
MODEL 021052
ASSEMBLY AND DRESSING INSTRUCTIONS
Blending innovative design, cutting-edge technology and the grace and elegance of traditional crystal, ALLEGRI® proudly brings you a new approach
to lighting. ALLEGRI® fixtures are made from the finest raw materials and are brought to life through a combination of traditional manufacturing, such
as sand casting, hand-forging and technology driven techniques including laser cutting.
Enclosed are detailed instructions on how to properly install your fixture. Please read all instructions carefully. If you need further assistance, please
contact the dealer from which you purchased this product or call 866-820-2665 to speak with an ALLEGRI® customer service representative. We hope
you enjoy your fixture!
WWW.ALLEGRICRYSTAL.COM
P1
866.820.2665
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY AND
PROPERTY DAMAGE. All electrical components must be installed only by a Licensed Electrician.
This product must be installed in accordance with the National Electric Code (NEC), and appropriate local electrical code(s), by a
person familiar with the construction and operation of the product and the hazard involved.*
CAUTION: Do not exceed maximum wattage note on fixture. Uses only recommended bulbs with fixture.
For your safety and proper operation of fixture, read and understand all instructions completely before commencing installation.
This fixture is suited for dry locations. Never install fixture on damp ceiling; room should be dry and well ventilated.
Extreme care should be taken to avoid damage to the surface of lighting fixture and wires. Wearing gloves is recommended for installation.
Connect ribbed wire of lighting fixture to live wire, while smooth wire of lighting to neutral. Connect bare copper or silver color ground wire of
fixture to the double colored or green wire of outlet box.
Use UL LISTED wire nuts for the wiring connections in this fixture. Wrap wire nut connections with UL LISTED electrical tape.
Keep lighting away from acid, alkali and other corrosive chemical or gas; clean the fixture with a clean cloth only.
Fixture must be firmly secured when installing ceiling tube, chain pipe and other connecting parts.
Never cover the lighting fixture when power is connected.
Disconnect the power before installing, cleaning and/or replacing light bulb.
Extreme care should be taken when installing and cleaning of Glass and/or Crystal Components.
This product is rated 110-130V/60HZ bulb 40W Maximum.
Save these instructions for future reference.
T
he electricity must be turned off at the main fuse box or circuit breaker before installing this fixture. Turning the power off using the light switch may
not be sufficient to prevent electrical shock.
*ALLEGRI will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
WWW.ALLEGRICRYSTAL.COM
P2
866.820.2665
Solid Nipple
Hex nut and washer
Screws
Plate Hickey
Outlet box (by others)
CRYSTAL BOWL
Mounting ring
WARNING
Electrical Danger Turn Power Off
All electrical components must be
installed by a licensed electrician in
accordance with the National
Electric code and the appropriate
local electrical codes.
R
Easy link (2pcs)
Chain
Collar loop ring
CAUTION: Be sure power is off at the main
breaker box prior to installation.
1. Drill a hole on main ceiling beam and pass
Solid Nipple through.
2.Place Washer and Hex Nut on top of Solid
Nipple to hold.
3. Take Outlet Box through Solid Nipple and
screw Plate Hickey, then screw Plate Hickey
to main ceiling beam with 4 screws.
4. Secure the Washer and Hex Nut to Solid
Nipple from top side of main ceiling beam.
5. Screw Collar Loop to Nipple as shown, raise
Canopy flat to ceiling and secure it with
Collar Loop Ring.
6. Hang Chain to Collar Loop with the Easy
Link, Proceed to fixture frame assembly Step
1.
P3
WWW.ALLEGRICRYSTAL.COM
866.820.2665
Loading...