Alarm Lock PG21 INSTALLATION GUIDE
INSTALLATION TEMPLATE--PG21 SERIES
USE LEFT SIDE OF PAGE
FOR OUTSWINGING DOORS
AS SHOWN IN THE "TOP
VIEW" BELOW (NOTE
LOCATION OF HINGE).
!
Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
USE RIGHT SIDE OF PAGE
FOR OUTSWINGING DOORS
AS SHOWN IN THE "TOP
VIEW" BELOW (NOTE
LOCATION OF HINGE).
JAM
PG21
MAGNETIC ACTUATOR
HINGE
DOOR
3/8"
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT WHEN
INSTALLING A RIM CYLINDER)
NOTE:
The Baseplate must be
mounted far enough away from
the edge of the door to prevent
unit from striking the door jam.
HINGE
DOOR
PG21
MAGNETIC ACTUATOR
JAM
Magnetic Actuator location is shown for reference
purposes only. For correct Magnet Actuator location,
use either (1) the location references printed on the
red stickers on the side of the PG21 cover, (2) Mag-
net Alignment Mode or (3) place the Magnetic Actua-
tor 1½ " from the bottom edge of the Baseplate. For
mounting hole sizes and depths, see reverse.
PG21 SERIES
ACTUATOR
MAGNETIC
MAGNETIC
ACTUATOR
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT FOR
EXTERNAL WIRING)
Magnetic Actuator location is shown for reference
purposes only. For correct Magnet Actuator location,
use either (1) the location references printed on the
red stickers on the side of the PG21 cover, (2) Mag-
net Alignment Mode or (3) place the Magnetic Actua-
tor 1½ " from the bottom edge of the Baseplate. For
mounting hole sizes and depths, see reverse.
!
Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
3/8"
ALARM LOCK
© ALARM LOCK 2003
345 Bayview Avenue, Amityville, New York 11701
FOLD UP ALONG THIS LINE & PLACE AGAINST EDGE OF DOOR
FOLD UP ALONG THIS LINE & PLACE AGAINST EDGE OF DOOR
WI1210A 9/03
INSTALLATION TEMPLATE--PG21 SERIES
USE LEFT SIDE OF PAGE
FOR DOORS SHOWN IN THE
"TOP VIEWS" BELOW
!
Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
FOLD UP ALONG THIS LINE. PLACE ON DOOR AND DOOR JAM
USE RIGHT SIDE OF PAGE
FOR DOORS SHOWN IN THE
"TOP VIEWS" BELOW
(Double Doors)
(Double Doors)
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT WHEN
INSTALLING A RIM CYLINDER)
NOTE:
Magnetic actuator can be
mounted close to the edge of the
door and door jam.
FOLD UP ALONG THIS LINE. PLACE ON DOOR AND DOOR JAM
Both the Baseplate and
PG21 SERIES
(Double Doors)
3/8"
(Double Doors)
Use 1/8" bit
(0.125").
Drill 1" deep.
Use 1/8" bit
(0.125").
Drill 1" deep.
ALARM LOCK
© ALARM LOCK 2003
345 Bayview Avenue, Amityville, New York 11701
Use 1/8" bit
(0.125").
Drill 1" deep.
MAGNETIC
ACTUATOR
(OPTIONAL--DO NOT DRILL
THIS HOLE EXCEPT FOR
EXTERNAL WIRING)
!
Holes for Baseplate
mounting screws.
Use 1/8" bit (0.125").
Drill 1" deep.
3/8"
MAGNETIC
ACTUATOR
Use 1/8" bit
(0.125").
Drill 1" deep.
WI1210A 9/03
Loading...