Alamo RX72, RX84, RX60 User Manual

Page 1

RX60 - RX72 - RX84

Rotary Mower

Rev 05-11 Part No. 00785503P

PART'S MANUAL

An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (800-356-6286) to obtain a Free copy before operating the equipment.

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 210-372-3551

Page 2

Page 3

TO THE OWNER/OPERATOR/DEALER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that

you retain. The use of "will-t" parts will void your warranty and can cause catastrophic failure with possible injury or death.

Page 4

BOLT TORQUE

Mounting procedures for mowers will require a signicant amount of bolt nut and washer installation.

Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness.

Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart.

Bolt tightness should be completed with and checked with a suitable torque wrench.

Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual.

Loose bolts on a frame or in a casting may be a result of:

● Vibration from the mower due to imbalance of the mower blades

● Pulled threads due to over tightening

● Distortion of the hole due to under tightening during installation

Bolts broken or sheared in the mounting structure or tractor may be the result of:

● Improper alignment of the Mounting Plate or Structure such that it is not sitting at on the mating surface

● Distortion of the bolt due to over-tightening

● Under tightening of the bolts

Check the bolt torque during installation and prior to delivery with a suitable torque wrench.

Page 5

PARTS

SECTION

Parts Section – 1

Page 6

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and

are subject to special handling. Request a quotation for such parts before sending a Purchase

Order.

6. The Manufacturer reserves the right to change prices without prior notice..

For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 830-379-1480

Parts Section – 2

Page 7

PART NAME INDEX

A-FRAME QUICK HITCH ASSEMBLY - RX60, RX72............................................................................................................................. 4

A-FRAME QUICK HITCH ASSEMBLY - RX84........................................................................................................................................ 5

A-FRAME QUICK HITCH ATTACHMENT - RX60, RX72...................................................................................................................... 6

A-FRAME QUICK HITCH ATTACHMENT - RX84.................................................................................................................................. 7

AXLE ASSEMBLY PULL TYPE - RX84.................................................................................................................................................... 8

BLADE PAN ASSEMBLY - RX60............................................................................................................................................................. 10

BLADE PAN ASSEMBLY - RX72............................................................................................................................................................. 11

BLADE PAN ASSEMBLY - RX84............................................................................................................................................................. 12

CASTER WHEEL AND HUB ASSEMBLY.............................................................................................................................................. 13

CHAINGUARD ASSEMBLY - DOUBLE FRONT RX84......................................................................................................................... 14

CHAINGUARD ASSEMBLY - DOUBLE REAR RX84........................................................................................................................... 15

CHAINGUARD ASSEMBLY - FRONT.................................................................................................................................................... 16

CHAINGUARD ASSEMBLY - REAR....................................................................................................................................................... 17

DEFLECTOR ASSEMBLY - FRONT........................................................................................................................................................ 18

DEFLECTOR ASSEMBLY - REAR........................................................................................................................................................... 19

DRIVELINE ASSEMBLY CV.................................................................................................................................................................... 20

DRIVELINE ASSEMBLY LIFT - RX60, RX72, RX84............................................................................................................................. 21

DRIVELINE ASSEMBLY LIFT CAT-5 - RX84........................................................................................................................................ 22

DRIVELINE JACKSHAFT ASSEMBLY - RX84...................................................................................................................................... 23

GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11616 - BELOW...................................................................................................... 24

GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11617 - CURRENT.................................................................................................. 26

GEARBOX ASSEMBLY - RX84 - SERIAL 10022 - BELOW.................................................................................................................. 28

GEARBOX ASSEMBLY - RX84 - SERIAL 10023 - CURRENT............................................................................................................ 30

GEARBOX ATTACHMENT RX60, RX72 SERIAL 11616-BELOW, & RX84....................................................................................... 32

GEARBOX ATTACHMENT RX72 SERIAL# 11617-CURRENT............................................................................................................ 33

HYDRAULIC CYLINDER......................................................................................................................................................................... 34

SKID SHOE ASSEMBLY........................................................................................................................................................................... 35

SLIP CLUTCH ASSEMBLY - RX60, RX72, RX84................................................................................................................................... 36

SLIP CLUTCH ASSEMBLY CAT-5 - RX84............................................................................................................................................. 37

TAILWHEEL ASSEMBLY - DUAL RX84................................................................................................................................................ 38

TAILWHEEL ASSEMBLY - RX60, RX72................................................................................................................................................ 39

TAILWHEEL ASSEMBLY - RX84............................................................................................................................................................ 40

TAILWHEEL HUB ASSEMBLY............................................................................................................................................................... 41

TONGUE ASSEMBLY - RX84.................................................................................................................................................................. 42

Page 8

A-FRAME QUICK HITCH ASSEMBLY - RX60, RX72

ITEM PART NO. QTY. DESCRIPTION

1 00780585 - FLAT,REAR BRACE - RX72

00781038 - FLAT,REAR BRACE - RX60

2 00780582 - FLAT, A-FRAME - RX72

00780563 - FLAT, A-FRAME, QUICK HITCH - RX60

3 00780549 - BAR, BRACE - RX72

00780603 - BAR, BRACE - RX60 4 00009500 - BOLT-HEX 3/4 NC 4-1/2 PL5 5 0758550030 - SPACER 6 00037200 - NUT TOPLOCK 3/4 NC PLC 7 2101120 - CARB 5/8 NC X 2-1/2 PL5 - RX72

4905 - CARB 5/8-11 NC 2 PL5 - RX60 8 0732020020 - BUSHING - RX72

523012 - BUSHING, ORDER 780 MIN HT - RX60 9 00756077 - WASHER,5/8 HARDENED 10 00695100 - NUT,TOPLOCK 5/8 NC PLB 11 02845600 - HEXB 5/8 NC 3 PL5 - RX72

00703200 - HHCS 5/8 NC 2 3/4 PL5 - RX60 12 00780592 - BUSHING, A-FRAME TOGGLE 13 02845500 - HEXB 5/8 NC 2 PL5

Page 9

A-FRAME QUICK HITCH ASSEMBLY - RX84

ITEM PART NO. QTY. DESCRIPTION

1 00781069 2 FLAT, REAR BRACE 2 00781411 1 FLAT, A-FRAME LH 3 00781410 1 FLAT, A-FRAME RH 4 00781117 2 FLAT, QUICK HITCH TOGGLE 5 0758550031 1 BUSHING 6 00761199 2 SPACER TUBE 7 0732020020 4 BUSHING 8 00756077 10 5/8 HARDENED WASHER 9 00695100 13 NUT,5/8 NC TOPLOCKNUT 10 02845500 1 BOLT, 5/8 X 2 11 00600700 2 HEXB 5/8 NC 3-1/4 PL5 12 02030300 1 NUT, 1" TOPLOCK 13 00750479 1 HEXB 1NC 4-3/4 PL5 14 2101120 2 CARB 5/8 X 2-1/2

Page 10

A-FRAME QUICK HITCH ATTACHMENT - RX60, RX72

ITEM PART NO. QTY. DESCRIPTION

1 00775243 2 PIN WRIST CAT 1&2 2 2196 2 CLIP (LYNCH PIN), 13/32 DIA. 3 00780663 1 FLAT, DRIVELINE STORAGE 4 00001800 1 LOCKNUT TLM 1/2 NC PLB 5 00748823 1 HHCS 1/2-13UNC 1-1/2 PL5 6 02845500 4 HEXB 5/8 NC 2 PL5 - RX72

00695100 4 LOCKNUT TOPLOCK 5/8NC PLB - RX60 7 00756077 4 WASHER,5/8 HARDENED 8 00761724 2 BUSHING HITCH 9 0732020020 2 BUSHING - RX72

523012 2 BUSHING, ORDER 780 MIN HT - RX60 10 00695100 2 NUT,TOPLOCK 5/8 NC PLB 11 00785238 2 BUSHING,CAT. II QUICK HITCH

Page 11

A-FRAME QUICK HITCH ATTACHMENT - RX84

ITEM PART NO. QTY. DESCRIPTION

1 69141 2 PIN, HITCH CAT II & III 2 2196 2 CLIP (LYNCH PIN), 13/32 DIA. 3 00780663 1 FLAT, DRIVELINE STORAGE 4 00001800 1 LOCKNUT TLM 1/2 NC PLB 5 00749130 1 HHCS 1/2-13UNC 1-3/4 PL5 6 00002700 2 FLATWASHER 1/2 PL STD 7 00750952 2 HEXB,5/8NC X 2-1/2,ZP,GRD5 8 0732020020 2 BUSHING 9 00756077 2 WASHER,5/8 HARDENED 10 00695100 2 LOCKNUT TOPLOCK 5/8NC PLB 11 00037100 2 HEXB 3/4 NC 2-1/2 PL5 12 511016 2 BUSHING YDP 13 5312316 2 WASHER, 3/4 14 00037200 2 NUT 3/4-NC TOPLOCK GRC PL

Page 12

AXLE ASSEMBLY PULL TYPE - RX84

Page 13

AXLE ASSEMBLY PULL TYPE - RX84

Continued... ITEM PART NO. QTY. DESCRIPTION

1 00781149 1 WDMT, AXLE - 284 2 00781178 1 ASY, LEVEL ROD - 284 3 651102 2 PIN, DRILLED 4 00002701 2 FLATWASHER, 3/4, TYPE AW, ZP 5 00755153 2 PIN, COTTER 3/16 X 1-1/2 PLATED 6 00001800 2 LOCKNUT TLM 1/2 NC PLB 7 00764375 2 HHCS 1/2NC X 3-1/4 PL5 8 00007800 2 HEXB 3/4 NC 3 PL5 9 511016 4 BUSHING 10 00775616A 2 ASY,HUB & SPINDLE 11 00037200 2 NUT 3/4-NC TOPLOCK GRC PL 12 00748823 2 HHCS, 1/2 - 13NC X 1-1/2 PL5 13 02959924 2 NUT, 1/4" NC 14 03200347 1 EMBLEM, SMV 15 00024100 4 1/4" FLATWASHER 16 10058000 2 HHCS 1/4 NC 1 PL5 17 8727A 1 HYDRAULIC CYLINDER 18 103266 1 CYLINDER PIN 19 02822500 2 FLATWASHER 1 PL STD 20 00606000 4 PIN, COTTER 3/16 X 2 21 7329 1 ADAPTER, HYD, STGHT 22 0652141311 1 STRAIGHT ADAPTER 8MP-8MJ 23 8354 1 PIN, HYD. CYLINDER 24 00785646 1 SMV BRACKET 25 00777963 1 TRANSPORT LOCK PLATE 26 00758643 1 ROD, CONTROL 27 00781177 1 WELDMENT LONG LEVEL ROD 28 00778159 1 NUT, 9" ADJUSTING 29 5C1490 1 HEXNUT, 7/8 JAM ZP

Page 14

BLADE PAN ASSEMBLY - RX60

ITEM PART NO. QTY. DESCRIPTION

1 00781388 1 WDMT,BLADE PAN (SERIAL# RX60-10042 AND BELOW)

00786797 1 WDMT,BLADE PAN (SERIAL# RX60-10043 TO CURRENT) 2 00780882 2 BLADE, CCW FAN 22-1/2 CTR-TIP 260

0652010030 2 BLADE, FLAT

00757830 2 BLADE, HIGH SUCTION TWISTED 3 00780945 2 WASHER 1-5/64 SQ HOLE X 3 OD 260 4 5GL16140 2 LOCKNUT 1 -14 LH TLN PL - 260 5 571044 2 BOLT SHOULDER - 260 6 571045 2 WASHER - HARDENED - 260

Page 15

BLADE PAN ASSEMBLY - RX72

ITEM PART NO. QTY. DESCRIPTION

1 00780622 1 WLDMT, BLADE PAN 272 (SERIAL# 11616-BELOW) 2 00786485 1 WLDMT, BLADE PAN 272 (SERIAL# 11617-CURRENT) 3 5GL16140 4 LOCKNUT 1 -14 LH TLN PL 4 571045 4 WASHER, HARDENED 5 571044 4 BOLT SHOULDER 6 00757830 2 BLADE, HIGH SUCTION TWISTED

0652010030 2 BLADE, FLAT

00780882 2 BLADE, CCW FAN 22-1/2 CTR-TIP 260 & 272 7 00780945 4 WASHER 1-5/64 SQ HOLE X 3 OD 8 00779283 4 WASHER, HARDENED BLADE WEAR

Page 16

BLADE PAN ASSEMBLY - RX84

ITEM PART NO. QTY. DESCRIPTION

1 00786649 1 WELDMENT, BLADE CARRIER 2 5GL16140 2 LOCKNUT 3 571045 2 WASHER 1 STRUCURAL 4 571044 2 BOLT, SHOULDER BLADE 5 00778047 2 BLADE WASHER 6 0582010330 2 BLADE, CCW FAN ROTARY MOWER

582013A 2 BLADE, FLAT

00757833 2 BLADE, HIGH SUCTION TWISTED

Page 17

CASTER WHEEL AND HUB ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00776220 1 CASTER WHEEL AND HUB ASSEMBLY 1 373024H 1 TIRE WHEEL ASSEMBLY 2 00780238 1 TAILWHEEL HUB ASSEMBLY INCLUDES ALL ITEMS EXCEPT 1, 13, 21, & 18 4 00776214 1 HUB 5 00776213 2 BEARING CONE & CUP 6 00776219 2 OIL SEAL 7 00772082 1 GREASE FITTING (THREADED) 8 00776216 4 BOLT 9 7A6166 4 BOLT 10 00776215 4 FLATWASHER 11 00012101 4 LOCKWASHER 12 00013901 4 NUT 13 0585020210A 1 CASTER FORK WELDMENT 14 00772017 2 BUSHING 15 00772018 2 DUST CAP 16 00776211 1 SPINDLE BOLT 17 02822500 1 WASHER 18 15B2400 1 FLATWASHER 19 00776212 1 CASTELLATED NUT 20 00771620 1 COTTER PIN 21 00758899 1 COTTER PIN

Page 18

CHAINGUARD ASSEMBLY - DOUBLE FRONT RX84

ITEM PART NO. QTY. DESCRIPTION

1 00785248 1 ASY,FRONT DOUBLE CG-RX84 2 00748823 7 HHCS 1/2-13UNC 1-1/2 PL5 3 00002700 7 FLATWASHER 1/2 PL STD

Page 19

CHAINGUARD ASSEMBLY - DOUBLE REAR RX84

ITEM PART NO. QTY. DESCRIPTION

1 00785249 1 ASY,REAR DOUBLE CG-RX84 2 00748823 9 HHCS 1/2-13UNC 1-1/2 PL5 3 00002700 18 FLATWASHER 1/2 PL STD 4 00001800 9 LOCKNUT TLM 1/2 NC PLB

Page 20

CHAINGUARD ASSEMBLY - FRONT

ITEM PART NO. QTY. DESCRIPTION

1 00781209 1 FLAT, FRONT C.G. BRACKET - RX72

00781249 1 FLAT, FRONT C.G. BRACKET - RX60

00781265 1 FLAT, FRONT C.G. BRACKET - RX84 2 00002700 5 FLATWASHER 1/2 PL STD - RX60 RX72

00002700 7 FLATWASHER 1/2 PL STD RX84 3 00748823 5 HHCS 1/2-13UNC 1-1/2 PL5 - RX60 RX72

00748823 7 HHCS 1/2-13UNC 1-1/2 PL5 - RX84

Page 21

CHAINGUARD ASSEMBLY - REAR

ITEM PART NO. QTY. DESCRIPTION

1 00785229 1 BRACKET,REAR CHAIN GUARD - RX72

00785230 1 ASY,REAR CHAIN GUARD - RX60

00781264 1 BRACKET,REAR CHAIN GUARD - RX84 2 00748823 9 HHCS 1/2-13UNC 1-1/2 PL5 - RX84 RX72

00748823 7 HHCS 1/2-13UNC 1-1/2 PL5 - RX60 3 00002700 18 FLATWASHER 1/2 PL STD - RX84 RX72

00002700 14 FLATWASHER 1/2 PL STD - RX60 4 00001800 9 LOCKNUT TLM 1/2 NC PLB - RX84 RX72

00001800 7 LOCKNUT TLM 1/2 NC PLB - RX60

Page 22

DEFLECTOR ASSEMBLY - FRONT

ITEM PART NO. QTY. DESCRIPTION

1 00780879 1 PANEL, FRONT RUBBER DEFLECTOR - RX72

00781039 1 PANEL, FRONT RUBBER DEFLECTOR - RX60

00781119 1 PANEL, FRONT DEFLECTOR - RX84 2 00780881 1 FLAT, DEFLECTOR STRAP - RX72

00781041 1 FLAT, DELFECTOR STRAP - RX60

00781144 1 FLAT, FRONT DEFLECTOR STRAP - RX84 3 00748823 5 HHCS 1/2-13UNC 1-1/2 PL5 - RX60 RX72

00748823 7 HHCS 1/2-13UNC 1-1/2 PL5 - RX84 4 00002700 5 FLATWASHER 1/2 PL STD - RX60 RX72

00002700 7 FLATWASHER 1/2 PL STD - RX84

Page 23

DEFLECTOR ASSEMBLY - REAR

ITEM PART NO. QTY. DESCRIPTION

1 00781231 1 PANEL, REAR RUBBER DEFLECTOR - RX72

00781229 1 PANEL, REAR RUBBER DEFLECTOR - RX60

00781079 1 PANEL, REAR DEFLECTOR - RX84 2 00781232 1 FLAT, REAR DEFLECTOR STRAP - RX72

00781230 1 FLAT, REAR DEFLECTOR STRAP - RX60

00781131 1 FLAT, REAR DEFLECTOR STRAP - RX84 3 00748823 9 HHCS 1/2-13UNC 1-1/2 PL5 - RX72 RX84

00748823 7 HHCS 1/2-13UNC 1-1/2 PL5 - RX60 4 00002700 18 FLATWASHER 1/2 PL STD - RX72 RX84

00002700 14 FLATWASHER 1/2 PL STD - RX60 5 00001800 9 LOCKNUT TLM 1/2 NC PLB - RX72 RX84

00001800 7 LOCKNUT TLM 1/2 NC PLB - RX60

Page 24

DRIVELINE ASSEMBLY CV

ITEM PART NO. QTY. DESCRIPTION

00779504 1 DRIVELINE ASSEMLBY CV 1 2716820 1 REPAIR KIT 2 00779522 1 ASY,SAFETY SLIDE LOCK YOKE 3 00779521 2 KIT,CROSS & BEARING 4 00779520 1 HOUSING,CENTER 6 00779051 1 GUARD REPAIR KIT (NOT SHOWN) 11 00780376 1 NYLON BEARING & KEEPER 13 00779519 1 KIT,CROSS & BEARING 14 00779518 1 YOKE 15 02956948 1 LOCKNUT 5/8 NC PLC 16 00765690 1 HHCS 5/8-11UNC 3LG GR8 PL

00779523 1 ASY,JOINT & TUBE 1/2 W/GUARD

00779524 1 ASY,JOINT & SHAFT 1/2 W/GUARD

00779525 1 ASY,GUARD SET

Page 25

DRIVELINE ASSEMBLY LIFT - RX60, RX72, RX84

ITEM PART NO. QTY. DESCRIPTION

00781390 1 DRIVELINE CAT4 1-3/4-20 SPLINE 1 00779516 1 YOKE 1 3/8" -6SPL 2 00779517 2 CROSS & BEARING KIT 3 00756934 2 PIN,ROLL 10 X 80 4 8982 1 YOKE INBOARD 7 8387 1 INBOARD YOKE 8 00779512 1 FRICTION CLUTCH 12 8393 2 BEARING RING 14 00759217 2 SCREW 1/2 LG #8 PAN 15 00756005 1 DECAL-ROTATING DRIVELINE 16 00756004 1 DECAL-SHIELD MISSING 17 8974 1 SUPPORT BEARING 18 1416601 1 ZERK

00779533 1 SHIELD KIT INCLUDES ITEMS 10, 11, 12, 14 & 15

Page 26

DRIVELINE ASSEMBLY LIFT CAT-5 - RX84

ITEM PART NO. QTY. DESCRIPTION

00781406 1 ASY,DRIVELINE W/CLUTCH,540RPM 1 W821A 1 YOKE 44 1-3/8-6 SLID 2 W840 2 KIT,CROSS SAME AS P 3 W816F 1 YOKE SHAFT PAINT BLA 4 00775344 1 YOKE, I.B. TUBE & SLEEVE W.A. 5 00779357 1 COMPT. CLUTCH HUB 1440 1350MM 6 00775345 1 OUTER SHIELD TUBE ASSY 7 00775346 1 INNER SHIELD TUBE ASSY 8 00775347 1 SHIELD BEARING 9 00775348 4 SUPPORT BEARING 10 00752670 2 FITTING,GREASE STRAIGHT 1/4-28

Page 27

DRIVELINE JACKSHAFT ASSEMBLY - RX84

ITEM PART NO. QTY. DESCRIPTION

00785491 1 JACKSHAFT 1 00779517 1 CROSS & BEARING KIT 2 00756934 1 SPRING PIN 10 X 80 3 8982 1 INBOARD YOKE 1B 4 8393 2 BEARING RING SC25 5 00759217 2 SCREW- IN ITEM 7 & 8 6 00756005 1 DECAL OUT. -IN ITEM 9 7 00756004 1 DECAL INN. -IN ITEM 1

00774208 1 CC LOCK ASSY - IN ITEM 6 8 00779512 1 CLUTCH

Page 28

GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11616 - BELOW

Page 29

GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11616 - BELOW

Continued... ITEM PART NO. QTY. DESCRIPTION

00780880P 1 ASY,GEARBOX, SUPER 75 1:1.6 SU 1 00781380 1 HOUSING 75 SERIES E.O. 2 00755954 8 LOCKWASHER M10 3 00758659 8 HEXB METRIC 10-P1.5 - 32MM PL5 4 00758664 1 CAP,INPUT IEG 20-001 5 00758689 1 SHAFT,INPUT 6 00758653 1 SEAL 1-3/4IDX2.378OD 7 00758667 1 SHIM .012 2.44 O.D. 8 00758668 1 SHIM,0.020 2.44 O.D. 9 00758646 1 SHIM, ADJUSTMENT - .004" 10 00758647 1 SHIM, ADJUSTMENT - .010" 11 00759977 1 SPACER GEAR MOUNT I 12 00781381 1 OUTPUT SPACER 13 00758663 1 CAP,OUTPUT IEG #20-002 14 00758672 4 LOCKWASHER,M12 IEG 07-002 15 02959661 4 HEXB, M12-P1.75 X 35MM PL8.8 17 00606000 1 PIN,COTTER 3/16X2 18 00758692 1 NUT SLOTTED HEX FLG 1-14UNS PL 19 00758674 1 SEAL,OUTPUT SHAFT 50 20 00758676 1 GASKET, .004 OR .1M 21 00758677 1 GASKET, .010 OR .25 22 00781382 1 OUTPUT SHAFT 23 00769938 2 BEARING #30210 24 00758698 1 GEAR,15 TOOTH 25 00762121 1 NUT,HEX THIN SLOTTED 26 00026200 1 PIN,COTTER 5/32 X 1-1/2 27 00755615 2 BEARING 28 00770737 2 LEVEL PLUG M18 X 1.5 29 00769321 3 WASHER,SEALING,17.8M 30 00758657 1 SPACER,INPUT SHAFT 31 00758701 1 GEAR,24 TOOTH 32 00778907 1 ASY,DIP STICK 33 00762114 1 PLUG,VENT W/WASHER 18M-P1.5

Page 30

GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11617 - CURRENT

Page 31

GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11617 - CURRENT

Continued... ITEM PART NO. QTY. DESCRIPTION

00785788 1 ASY,GEARBOX - NON-LUBED - GEAR IN FRONT 540 RPM,1:1.50 RATIO,1-3/4-20 SPLINE 1 00786292 1 KIT,ROLLER BEARING 2 00786293 1 KIT,GEAR SET 3 00786294 1 KIT,SEAL & SHIM 5 00758484 1 DIPSTICK VENT PLUG 1/2" - FILL 7 00786287 1 SHAFT,INPUT - 1-3/4-20 SPL. 9 00786305 1 COVER,GEAR BOX 10 00755633 1 PLUG,SOLID GAS - 3/8" 11 00754764 4 HEXB M10 X 1.25 X 20 PL.8.8 17 00786288 1 SHAFT,OUTPUT 18 00755621 1 NUT,CASTLE - M30 X 1.5 19 70499 1 PIN,COTTER - B5 X 60 21 00755624 1 NUT,CASTLE - M30 X 2.0 25 00755623 1 WASHER,BOLT - 31 X 56 X 6 26 2716423 1 PIN,COTTER B6 X 60

Page 32

GEARBOX ASSEMBLY - RX84 - SERIAL 10022 - BELOW

Page 33

GEARBOX ASSEMBLY - RX84 - SERIAL 10022 - BELOW

Continued... ITEM PART NO. QTY. DESCRIPTION

00781080P 1 GEARBOX ASSEMBLY 1 00781380 1 HOUSING 75 SERIES E.O. 2 00755954 1 LOCKWASHER M10 SPRING 3 00758859 8 M10 X 1.5 X 30 HEX HEAD SCREW 4 00758664 1 CAP, INPUT IEG 20-001 5 00758689 1 SHAFT, INPUT 6 00758653 1 SEAL 1-3/4ID X 2.378OD 7 00758667 1 SHIM .012 2.44 O.D. 8 00758668 1 SHIM,0.020 2.44 O.D. 9 00758646 1 SHIM, ADJUSTMENT - .004 10 00758647 1 SHIM, ADJUSTMENT - .010 11 00759977 1 SPACER GEAR MOUNT I 12 00781381 1 OUTPUT SPACER 13 00758663 1 CAP,OUTPUT IEG #20-002 14 00758672 4 LOCKWASHER, M12 IEG 07-002 15 02959661 4 HEXB, M12-P1.75 X 35 MM PL8.8 17 00606000 1 COTTER PIN 3/16" X 2" 18 00758692 1 NUT SLOTTED HEX FLG 1-14 UNS PL 19 00758674 1 OUTPUT OIL SEAL 20 00758676 1 GASKET, .004 OR .1M 21 00758677 1 GASKET, .010 OR .25 22 00781382 1 OUTPUT SHAFT 23 00769938 1 BEARING #30210 24 00781088 1 GEAR, 16 TOOTH PINION 25 00762121 1 NUT, HEX, THIN SLOTTED 26 00026200 1 PIN,COTTER 5/32 X 1-1/2 27 00755615 1 BEARING #30209 28 00770737 1 LEVEL PLUG M 18 X 1.5 29 00769321 1 WASHER, SEALING 30 00758657 1 SPACER, INPUT SHAFT 31 00781089 1 GEAR, 22 TOOTH 32 00778907 1 ASSY-DIPSTICK FOR SUPER 75 GBS 33 00762114 1 PLUG,VENT, 18M-P1.5 5PSI

Page 34

GEARBOX ASSEMBLY - RX84 - SERIAL 10023 - CURRENT

Page 35

GEARBOX ASSEMBLY - RX84 - SERIAL 10023 - CURRENT

Continued... ITEM PART NO. QTY. DESCRIPTION

00785790 1 ASY, GEARBOX 1 00786296 1 GEAR,CROWN Z22 M6 2 00755615 2 BEARING,ROLLER - 30209 3 00755619 2 SHIM KIT - 70.3MM X 84.7MM 4 00755618 2 SNAP RING - 85MM X 88.5MM X 3MM 5 00755634 1 CAP,OIL - 85MM X 10MM 6 00786287 1 SHAFT,INPUT - 1-3/4-20 SPL. 7 00786291 1 SEAL,OIL - 45MM X 85MM X 10MM 8 00786305 1 COVER,GEAR BOX 9 00755633 1 PLUG,SOLID GAS - 3/8" 10 00754764 4 HEXB M10 X 1.25 X 20 PL.8.8 11 00786297 1 GEAR,PINION Z18 M6 12 2516460 1 SNAP RING - 50MM X 47MM X 3MM 13 00755632 1 SHIM KIT - 45.3MM X 65.3MM X 2.5MM 14 00769938 2 BEARING,ROLLER - 30210 15 00755622 1 SHIM KIT - 50.3MM X 70.3MM 16 00786295 1 SHAFT,OUTPUT 17 00756943 1 NUT,CASTLE - M40 X 1.5 18 70499 1 PIN,COTTER - B5 X 60 19 00786298 1 SHIM KIT - 40.3MM X 61.7MM X 1.0MM 20 00755624 1 NUT,CASTLE - M30 X 2.0 21 00755627 1 SEAL,OIL - 50MM X 90MM X 10MM 22 00755626 1 WASHER,PROTECTIVE 23 00755623 1 WASHER,BOLT - 31 X 56 X 6 24 00754336 1 1/2" GAS SOLID PLUG 25 2716423 1 PIN,COTTER B6 X 60 26 00786292 1 KIT,ROLLER BEARING 27 00786299 1 KIT,GEAR SET 28 00786294 1 KIT,SEAL & SHIM 29 00758484 1 DIPSTICK VENT PLUG 1/2" - FILL

Page 36

GEARBOX ATTACHMENT RX60, RX72 SERIAL 11616-BELOW, & RX84

ITEM PART NO. QTY. DESCRIPTION

1 00775571 1 WLDMT SHIELD 2 00775573 1 WLDMT BRKT SHIELD 3 00778907 1 ASSY-DIPSTICK FOR SUPER 75 GBS 4 00762114 1 PLUG,VENT W/WASHER 18M-P1.5 5 02845500 6 HEXB 5/8 NC 2 PL5 6 00695100 6 LOCKNUT TOPLOCK 5/8NC PLB 7 00756077 6 WASHER,5/8 HARDENED 8 00002700 1 FLATWASHER 1/2 PL STD 9 00002000 3 HEX CAP 3/8-16 X 3/4 GR.5 ZP 10 00012101 3 LOCKWASHER 3/8 PL 11 00011100 3 FLATWASHER STD 3/8 12 5F8130 1 1/2 NC WING NUT

Page 37

GEARBOX ATTACHMENT RX72 SERIAL# 11617-CURRENT

ITEM PART NO. QTY. DESCRIPTION

1 00785575 1 GEARBOX SCHIELD, 4-1/8"-5" BC 2 00785574 1 RING,GB SHIELD INNER SUPPORT 3 00023500 4 FLATWASHER, 5/16" TYPE AW, ZP 4 02958784 4 BOLT METRIC 8-P1.25-20MM PL8.8 5 00037200 6 LOCKNUT, 3/4"-NC TLM PL C 6 5312316 6 WASHER, 3/4" HARDENED 7 00037100 6 HEXB 3/4" NC 2-1/2" PL5

Page 38

HYDRAULIC CYLINDER

ITEM PART NO. QTY. DESCRIPTION

8727A 1 HYDRAULIC CYLINDER 1 00774729 1 CLEVIS CAP 2.5-3/4 ORB-1.00 2 00774734 1 ROD CAP 2.50-1.25-3/4 ORB 3 00774730 1 PISTON 2.5-0.75-S HALL W/RING 4 00774753 1 ROD CYL 1.25-08-0.75-1.25-A 5 3047111 1 CYLINDER TUBE 6 3047112 4 TIE ROD 9 00774760 1 SEAL KIT 15 3047117 1 THREAD LOCK 16 1917140 1 ROD CLEVIS 17 00774740 1 SC SCKT SET 3/8UNCX1/2 KNUR 18 33003H5C 8 HEX NUT 3/8-16 GR.5 19 5JRC12160 1 NUT TOPLOCK 3/4 NF PLC 20 1917132 1 SCKT HD O-RNG PLUG,3/4-16 UNF 21 2417154 1 BREATHER,CYLINDER #8 ORB

Page 39

SKID SHOE ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

1 00778905 2 SKID SHOE BAR 2 8277 6 PLOW BOLT 3/8 NC 1-1/4 #3 PL 3 4528 6 NUT, LOCK 3/8-16 FLG WHIZ

Page 40

SLIP CLUTCH ASSEMBLY - RX60, RX72, RX84

ITEM PART NO. QTY. DESCRIPTION

00779512 1 SLIP CLUTCH ASSEMBLY 1 00779511 1 FLANGE YOKE 2 00754202 2 RING,CLUTCH LINING 3 00775322 1 HUB 1 3/4-20 I.C. 4 00775323 1 PLATE, THRUST 5 00775324 1 SPRING, BELLEVILLE 6 61064C8 6 M10X1.5X50 GR.8.8 HEX CAPSCREW 7 00765961 6 NUT MET TLE 10MM-P1.5 PL 8 00772648 2 NUT,HEX TOP LOCK-M12 X 1.75 9 61076C8 2 M12X1.75X65 GR.8.8 HEX CAPSCRE

Page 41

SLIP CLUTCH ASSEMBLY CAT-5 - RX84

ITEM PART NO. QTY. DESCRIPTION

1 00775383 1 YOKE FLANGE 2 0921000462 4 DISK, CLUTCH 5-15/16X3-19/32X 3 00779366 1 HUB 1-3/4-20 4 00775335 1 DRIVE PLATE 5 00779365 1 DRIVE PLATE 6 00775337 1 THRUST PLATE 7 00775338 6 BOLT HEX M12 X P1.25 X 115M 8 00775339 6 COMPRESSION SPRING 9 00754566 6 LOCKWASHER, 12MM 10 00756164 6 NUT METRIC 12MM-P1.75 GR.8.8 11 00774208 1 LOCK ASY CC YOKE

Page 42

TAILWHEEL ASSEMBLY - DUAL RX84

ITEM PART NO. QTY. DESCRIPTION

1 00781077 2 WDMT, T/W BEAM - 284/484 2 00781071 2 FLAT, POSITION BRACKET 3 00785473 2 MOUNT, DUAL TAILWHEEL BEAM 4 00007800 2 HEXB 3/4 NC 3 PL5 5 00037200 2 LOCKNUT 3/4-NC TLM PLC 6 00749130 8 HHCS 1/2-13 UNC 1-3/4 PL5 7 00001800 8 LOCKNUT TLM 1/2 NC PLB 8 00776220 1 WHEEL & FORK ASSEMBLY

Page 43

TAILWHEEL ASSEMBLY - RX60, RX72

ITEM PART NO. QTY. DESCRIPTION

1 00780876 1 WDMT, T/W BEAM - 272

00781036 1 WDMT, T/W BEAM - 260 2 0585020300 1 BRACKET, POSITION 3 00785239 1 MOUNT, TAILWHEEL BEAM 4 00059000 1 HEXB 5/8 NC X 5 PL5 5 00695100 1 LOCKNUT TOPLOCK 5/8NC PLB 6 00748823 4 HHCS 1/2-13 UNC 1-1/2 PL5 7 00001800 4 LOCKNUT TLM 1/2 NC PLB 8 00776220 1 ASSY CASTER FORK & WHEEL

Page 44

TAILWHEEL ASSEMBLY - RX84

ITEM PART NO. QTY. DESCRIPTION

1 00781077 1 WELDMENT, T/W BEAM 2 0585020300 1 BRACKET POSITION 3 00785473 1 MOUNT, T/W BEAM 4 00007800 1 HEXB 3/4 NC3 PL5 5 00781367 1 TUBE BUSHING 6 00037200 1 LOCKNUT 3/4 NC TLM PLC 7 00749130 4 HHCS 1/2-13UNC 1-3/4 PL5 8 00001800 4 TOPLOCKNUT, 1/2-13 NC PL 9 15B2400 4 FLATWASHER NAR 1-1/2 PL 10 00758899 1 PIN COTTER 3/8X2-1/2 PL EXTEND 11 00776220 1 ASY,CASTER FORK & WHEEL

Page 45

TAILWHEEL HUB ASSEMBLY

ITEM PART NO. QTY. DESCRIPTION

00780238 1 ASSY, TAILWHEEL HUB 1 00776214 1 HUB 4 BOLT 2 00776213 2 BEARING 3 00759635 4 FLATWASHER 1/2 HARDND NONPLATD 4 00762462 4 HEXB METRIC 12-P1.75- 25MM PL5 5 00772017 2 BUSHING SPINDLE STEP 6 00772018 2 DUST CAP 7 00776219 2 SEAL OIL 40 X 62 X 8 8 00776211 1 BOLT SPINDLE M24 X 2 X 186 9 00776217 2 WASHER FLAT 026 X 044 X 4 FLAT 10 00776212 1 NUT SPINDLE M24 X 2 11 00772082 1 NIPPLE, GREASE M8X1 12 00771620 1 PIN,COTTER 5/32X2-1/2 PL

Page 46

TONGUE ASSEMBLY - RX84

Page 47

TONGUE ASSEMBLY - RX84

Continued... ITEM PART NO. QTY. DESCRIPTION

1 00777459 1 WDMT, TONGUE 2 00778053 1 WDMT, CLEVIS 3 00760941 1 WDMT, JACK TUBE MOUNT 4 00764515 1 CHAIN, SAFETY TOW-6000# CAP. 5 1431565 1 SHAFT, PTO IID TRANSPORT SUPPRT 6 40010000 1 PIN, COTTER 1/8 X1 7 00755076 1 HHCS 1 NC 5-1/2 PL8 8 00759275 3 WASHER, HITCH CLEVIS 9 02030300 3 NUT TOPLOCK 1 NC PLB 10 00754107 2 BOLT 1 - 8UNC X 6-1/2 PL8 11 00756077 2 WASHER, 5/8 HARDENED 12 00695100 2 LOCKNUT TOPLOCK 5/8 NC PLB 13 00761890 2 BUSHING 1.5 OD X 1.14 IDX 1-3/16 LG 14 00758146 2 PIN, TONGUE PIVOT 15 2196 2 CLIP (LYNCH PIN), 13/32 DIA. 16 00772391 1 PARKING JACK SIDEWIND 17 00695100 4 NUT, 5/8 NC TOPLOCK 18 00001400 8 FLATWASHER 5/8 PL STD 19 00775006A 1 BEARING ASSEMBLY 20 00002701 2 FLATWASHER, 3/4, TYPE AW, ZP 21 00037200 1 LOCKNUT 3/4-NC TLM PLC 22 00002700 1 FLATWASHER 1/2 23 5F8130 1 WINGNUT 1/2 NC 24 00781172 1 HHCS 3/4 NC 8-1/2 PL5 25 02845800 4 HEXB, 5/8 NC X 4-1/2 GRD5 ZP 26 00749130 2 HHCS 1/2 - 13 UNC 1-3/4 PL5 27 00002000 1 HEX CAP 3/8 - 16 X 3/4 GR.5 ZP 28 00012101 1 LOCKWASHER 3/8 PL 29 00011100 1 FLATWASHER 3/8 PL STD 30 00781166 1 FLAT, LH BEARING PIVOT 31 00781167 1 FLAT, RH BEARING PIVOT 32 00781174 1 WELDMENT, SHIELD BRACKET 4 BOLT

00781168 1 WELDMENT, SHIELD BRACET 3 BOLT 33 00786671 1 WLDMT, J/S SHIELD 34 00781175 1 FLAT, REINFORCING STRAP

RX60 - RX72 - RX84 (01-10) Rev 05-11

Page 48

Page 49

TO THE OWNER/OPERATOR/DEALER

To keep your implement running efciently and safely, read your manuals thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identies each section where you can easily nd the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators:

REQUIRED OF THE OWNER

1. Provide a Roll-Over-Protective Structure that meets the requirements of this standard.

2. Provide seat belts that meet the requirements of this paragraph of this standard and SAE J4C.

3. Ensure that each employee uses such seat belt while the tractor is moving.

4. Ensure that each employee tightens the seat belt sufciently to conne the employee to the

protected area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seat belt if the tractor has a ROPS.

2. Where possible, avoid operating the tractor near ditches, embankments, and holes.

3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.

4. Stay off slopes too steep for safe operation.

5. Watch where you are going, especially at row ends, on roads, and around trees.

6. Do not permit others to ride.

7. Operate the tractor smoothly, no jerky turns, starts, or stops.

8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer.

9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machinery guards in place...

Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.

Page 50

ALAMO INDUSTRIAL

Limited Warranty

1. Limited Warranties

1.01. Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“purchaser”) and warrants for six months to the original commercial or industrial purchaser (“purchaser”) that the goods purchased are free from defects in material or workmanship.

1.02. Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.

1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modication, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specically found in your operator’s manual.

1.04. Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf

of manufacturer.

2. Remedies And Procedures

2.01. This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 30 days of purchase.

2.02. Purchaser claims must be made in writing to the authorized dealer (“dealer”) from whom purchaser purchased the goods or an approved authorized dealer (“dealer”) within 30 days after purchaser learns of the facts on which the claim is based.

2.03. Purchaser is responsible for returning the goods in question to the dealer.

2.04. If after examining the goods and/or parts in question, manufacturer nds them to be defective under normal use and service due to defects in material or workmanship, manufacturer will:

(A) repair or replace the defective goods or part(s) or (B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser

paid for the repair and/or replacement prior to the nal determination of applicability of the warranty by manufacturer. The choice of remedy shall belong to manufacturer.

2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the dealer to the designated factory.

3. Limitation Of Liability

3.01. Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not limited to, merchantability and tness for a particular purpose.

3.02. Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods.

3.03. Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty. Not withstanding the above limitations and warranties, manufacturer’s liability hereunder for damages incurred by purchaser or others shall not exceed the price of the goods.

3.04. No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two (2) years after the cause of action has occurred.

4. Miscellaneous

4.01. Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas.

4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.

4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.

4.04. Applicable law may provide rights and benets to purchaser in addition to those provided herein.

Keep for your records

Attention: Purchaser should ll in the blanks below for his reference when buying repair parts and/or for proper machine identication

Alamo Industrial Implement Model ____________________________ Serial Number ________________________________ Date Purchased __________________________________________ Dealer ______________________________________

Attention: Read your operator’s manual

when applying for warranty.

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 830-379-1480

Page 51

Page 52

RX60 - RX72 - RX84 Pub 01-10 P/N 00785503P

Alamo RX72, RX84, RX60 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual