Alamo MACHETE2 02986941P User Manual

Page 1

Boom Arm Mower

Pub 12-08

Part No. 02986941P

PART'S MANUAL

An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800446-5158) to obtain a Free copy before operating the equipment.

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 210-372-3551

Page 2

Page 3

TO THE OWNER/OPERATOR/DEALER

RED

002369

LOCK UP.

5. TRANSPORT SAFELY,

6. USE SMV, LIGHTS, &

REFLECTORS.

7. DO NOT OPERATE WITH MOWER OR WING RAISED.

8. DO NOT MOUNT OR DISMOUNT WHILE MOVING.

4. BLOCK UP SECURELY BEFORE WORKING UNDER.

3. USE SAFETY SHOES,HARD HAT, SAFETY GLASSES, SEAT BELTS, & ROPS.

2. NO RIDERS, NO CHILDREN

OPERATORS.

MANUAL

READ

Never mount or dismount a moving vehicle. Crushing from runover may cause injury or death.

Put tractor in park or set brake, disengage PTO, stop engine, remove key, and wait until noise of rotation has ceased

to prevent entanglement in rotating parts which may cause injury or death.

8. Before dismounting, secure flail mower in transport position or lower to ground.

7. Never operate with Flail Mower or Folding Section raised if passersby, bystandards or traffic are in the area to reduce possibility of injury or death from objects thrown by Blades under Shields or implement structure.

6. Make certain that SMV sign, Warning Lights, and Reflectors are clearly visible. Follow local traffic codes.

Install Restrictor in folding circuit to slow down lowering and unfolding if action is faster than is desirable.

5. Before transporting, put Lift Lever in detent or full-lift position. Install Transport Safety Devices securely on folding implements. Slowdown when turning and on hillsides.

4. Block up or support raised machine and all lifted components securely before putting hands or feet under or working underneath any lifted component to prevent crushing injury or death from sudden dropping or inadvertent operation of controls. Make certain that area is clear before lowering or folding.

3. Operate only with tractor having Roll-Over Protective Structure (ROPS) and with seatbelt fastened securely and snugly to prevent injury and possible death from falling off or tractor overturn. Personal Protective Equipment such as Hard Hat, Safety Glasses, Safety Shoes, and Ear Plugs are recommended.

2. Allow no children on or near implement of tractor. Allow no riders on tractor or implement. Falling off can cause serious injury or death from being runover by tractor or mower or contact with Flail Mower Blades.

Learn how to stop engine suddenly in an emergency. Be alert for passersby and especially children.

1. Study and understand Operator's Manuals, Safety Signs, and Instructional Decals for tractor & flail mower to prevent misuse, abuse, & accidents. Practice before operating mower in a confined area or near passersby.

FAILING TO FOLLOW SAFETY MESSAGES AND OPERATING INSTRUCTIONS CAN CAUSE SERIOUS BODILY INJURY OR EVEN DEATH TO OPERATOR AND OTHERS IN THE AREA.

DANGER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.

Observe the rules of safety and common sense!

FAILING TO FOLLOW SAFETY MESSAGES AND OPERATING INSTRUCTIONS CAN CAUSE SERIOUS BODILY INJURY OR EVEN DEATH TO OPERATOR AND OTHERS IN THE AREA.

2. NO RIDERS, NO CHILDREN

3. USE SAFETY SHOES,HARD HAT, SAFETY GLASSES, SEAT BELTS, & ROPS.

4. BLOCK UP SECURELY BEFORE WORKING UNDER.

Learn how to stop engine suddenly in an emergency. Be alert for passersby and especially children.

5. Before transporting, put Lift Lever in detent or full-lift position. Install Transport Safety Devices securely on folding implements. Slowdown when turning and on hillsides.

Install Restrictor in folding circuit to slow down lowering and unfolding if action is faster than is desirable.

6. Make certain that SMV sign, Warning Lights, and Reflectors are clearly visible. Follow local traffic codes.

8. Before dismounting, secure flail mower in transport position or lower to ground. Put tractor in park or set brake, disengage PTO, stop engine, remove key, and wait until noise of rotation has ceased

to prevent entanglement in rotating parts which may cause injury or death.

Never mount or dismount a moving vehicle. Crushing from runover may cause injury or death.

5. TRANSPORT SAFELY,

6. USE SMV, LIGHTS, &

LOCK UP.

7. DO NOT OPERATE WITH MOWER OR WING RAISED.

8. DO NOT MOUNT OR DISMOUNT WHILE MOVING.

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.

Page 4

PARTS

SECTION

Parts Section – 1

Page 5

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

NOTE: Please refer to The Safety Section in the front of this Manual for the proper

Part Number when ordering Replacement Safety Decals.

For maximum safety and to guarantee optimum product reliability, always use genuine Servis-Rhino Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 830-379-1480

Parts Section – 2

Page 6

PART NAME INDEX

50 IN ROTARY - BLADE BAR - HEAD ASY (SOLID MNT).................................................................................................................... 5

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SOLID MNT).......................................................................................................... 7

50 IN ROTARY - BLADE BAR - HEAD ASY (SWIVEL MNT)............................................................................................................... 9

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SWIVEL MNT).................................................................................................... 11

50 IN ROTARY - BLADE BAR ASY......................................................................................................................................................... 13

50 IN ROTARY - BLADE PAN - HEAD ASY (SOLID MNT)................................................................................................................. 15

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SOLID MNT)........................................................................................................ 17

50 IN ROTARY - BLADE PAN - HEAD ASY (SWIVEL MNT).............................................................................................................. 19

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SWIVEL MNT)..................................................................................................... 21

50 IN ROTARY - BLADE PAN ASY......................................................................................................................................................... 23

60 IN ROTARY - BLADE BAR ASY......................................................................................................................................................... 24

60 IN ROTARY - HEAD ASY (SOLID MNT)........................................................................................................................................... 25

60 IN ROTARY - HEAD SUB-ASY (SOLID MNT).................................................................................................................................. 27

60 IN ROTARY - HEAD ASY (SWIVEL MNT)....................................................................................................................................... 29

60 IN ROTARY - HEAD SUB-ASY (SWIVEL MNT).............................................................................................................................. 31

ROTARY - MOTOR AND SPINDLE ASY................................................................................................................................................ 33

ROTARY - MOTOR ASY (PART 1).......................................................................................................................................................... 35

ROTARY - MOTOR ASY (PART 2).......................................................................................................................................................... 37

ROTARY - SPINDLE ASY......................................................................................................................................................................... 39

BOOM ASY - 18 FT BOOM (PART 1)...................................................................................................................................................... 41

BOOM ASY - 18 FT BOOM (PART 2)...................................................................................................................................................... 43

BOOM ASY - 22 FT BOOM (PART 1)...................................................................................................................................................... 45

BOOM ASY - 22 FT BOOM (PART 2)...................................................................................................................................................... 47

BOOM ASY - 25 FT BOOM (PART 1)...................................................................................................................................................... 49

BOOM ASY - 25 FT BOOM (PART 2)...................................................................................................................................................... 51

COMMON CRATE COMPONENTS......................................................................................................................................................... 53

DECALS - 18-22-25 FT BOOM.................................................................................................................................................................. 55

DECALS - 50 & 60 IN ROTARY HEAD................................................................................................................................................... 56

DECALS - HYD TANK AND PUMP......................................................................................................................................................... 57

FILTER ASY................................................................................................................................................................................................ 58

HIGH FRAME MOUNT ASY - 2WD......................................................................................................................................................... 59

HIGH FRAME MOUNT ASY - 4WD......................................................................................................................................................... 61

HIGH FRAME MOUNT SUB-ASY............................................................................................................................................................ 63

HOSE ROUTING - 18 FT BOOM............................................................................................................................................................... 65

HOSE ROUTING - 18 FT BOOM NOTES................................................................................................................................................. 66

HOSE ROUTING - 22 FT BOOM............................................................................................................................................................... 67

HOSE ROUTING - 22 FT BOOM NOTES................................................................................................................................................. 68

HOSE ROUTING - 25 FT BOOM............................................................................................................................................................... 69

HOSE ROUTING - 25 FT BOOM NOTES................................................................................................................................................. 70

HOSE ROUTING - HYDRAULIC KIT...................................................................................................................................................... 71

Page 7

PART NAME INDEX

HYDARULIC CYLINDER ASY - DIPPER 22-25 FT BOOM.................................................................................................................. 73

HYDARULIC CYLINDER ASY - LIFT BOOM........................................................................................................................................ 74

HYDRAULIC CYLINDER ASY - HEAD SWIVEL (OPTIONAL).......................................................................................................... 75

HYDRAULIC CYLINDER ASY - TILT.................................................................................................................................................... 76

HYDRAULIC TANK SUB-ASY................................................................................................................................................................ 77

HYDRAULIC TANK W/PUMP AND ELECT VALVE ASY................................................................................................................... 79

JOYSTICK CONSOLE ASY....................................................................................................................................................................... 81

PUMP ASY - SERVO CONTROLLED (PART 1)..................................................................................................................................... 83

PUMP ASY - SERVO CONTROLLED (PART 2)..................................................................................................................................... 85

PUMP-TANK-VALVE COVER................................................................................................................................................................. 87

VALVE ASSEMBLY - ELECTRO-HYDRAULIC VALVE..................................................................................................................... 89

WIRE HARNESS ELECT-HYD VALVE................................................................................................................................................... 91

Page 8

50 IN ROTARY - BLADE BAR - HEAD ASY (SOLID MNT)

Page 9

50 IN ROTARY - BLADE BAR - HEAD ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986704 1 ASY, 50" ROT, PISTON, BAR 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 34 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981757 2 WELDMENT, PIN, HITCH POST 14 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 15 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 16 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 17 651102 1 PIN-DRILLED 18 02976448 1 PIN - MACHINED HEAD 19 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 20 02968837 1 PLASTIC TIE, YELLOW & WHITE 21 02968836 1 PLASTIC TIE, YELLOW 22 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90

Page 10

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SOLID MNT)

Page 11

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986704 1 ASY, 50" ROT, PISTON, BAR 1 00015800 18 LOCKNUT TLM 3/8 NC PLC 2 02891800 4 HHCS 1/2 NC 1-3/4 PL8 3 00019600 4 LOCKWASHER 1/2 HEAVY 4 02982907 2 SKID SHOE 5 02981411 1 WELDMENT, DECK 50" HEAD 6 02961038 1 GASKET 7 02982906 1 ASY, BLADE BAR W/BLADES 8 02964861 4 SHCS 3/4 NC 4" LG PL8 9 15B600 14 WASHER 3/8 SAE P 10 00003901 4 LOCKWASHER 3/4 HEAVY 11 00059700 14 FSCS 3/8 NC X 1-1/4 12 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 13 03200269 8 HHCS 3/4 NC 3 PL8 14 02892100 8 HHCS 3/4 NC X 1 3/4" LG 15 00037200 16 NUT 3/4 NC LOCKNUT 16 5312316 16 FLATWASHER 3/4 HARDENED 17 02986200 1 WELDMENT, HITCH POST 18 02979881 1 MOTOR PISTON 4.91 CID 19 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 20 02968894 1 PLASTIC TIE, RED, 11LG 21 02968896 1 PLASTIC TIE, ORANGE, 11LG 22 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 23 00022200 8 LOCKWASHER 7/16 PL 24 02968895 1 PLASTIC TIE, BLUE, 11LG 25 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG

Page 12

50 IN ROTARY - BLADE BAR - HEAD ASY (SWIVEL MNT)

Page 13

50 IN ROTARY - BLADE BAR - HEAD ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986197 1 ASY, 50" ROT, PISTON, BAR, SW 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 20 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 14 02981757 2 WELDMENT, PIN, HITCH POST 15 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 16 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 17 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 18 651102 1 PIN-DRILLED 19 02976448 1 PIN - MACHINED HEAD 20 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 21 03200267 1 HHCS 3/4 NC 5 PL8 22 02963646 3 HHCS 3/4 NC 2-1/2 PL8 23 00037200 18 NUT 3/4 NC LOCKNUT 24 02968837 1 PLASTIC TIE, YELLOW & WHITE 25 02968836 1 PLASTIC TIE, YELLOW 26 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 27 02968832 1 PLASTIC TIE, GREEN 28 02968833 1 PLASTIC TIE, GREEN & WHITE 29 03200762 2 ADP, HYD 6MB-4MJ 90 30 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 31 02968894 1 PLASTIC TIE, RED, 11LG 32 02968895 1 PLASTIC TIE, BLUE, 11LG 33 02968896 1 PLASTIC TIE, ORANGE, 11LG

Page 14

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SWIVEL MNT)

Page 15

50 IN ROTARY - BLADE BAR - HEAD SUB-ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986197 1 ASY, 50" ROT, PISTON, BAR, SW 1 00015800 20 LOCKNUT TLM 3/8 NC PLC 2 02963646 3 HHCS 3/4 NC 2-1/2 PL8 3 00037200 18 NUT 3/4 NC LOCKNUT 4 02968894 1 PLASTIC TIE, RED, 11LG 5 02968896 1 PLASTIC TIE, ORANGE, 11LG 6 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 7 02891800 4 HHCS 1/2 NC 1-3/4 PL8 8 02979881 1 MOTOR PISTON 4.91 CID 9 00022200 8 LOCKWASHER 7/16 PL 10 00019600 4 LOCKWASHER 1/2 HEAVY 11 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 12 02980237 1 O-RING .139 DIA X 1.296 INSIDE 13 02982907 2 SKID SHOE 14 02981820 28 SHCS 1/2 NC X 1 1/2" LG PL8 15 02981318 1 SLEWING BEARING, 12 OD X 5.8 ID 16 02985319 1 WELDMENT, HITCH POST 17 02981411 1 WELDMENT, DECK 50" HEAD 18 02961038 1 GASKET 19 02982906 1 ASY, BLADE BAR W/BLADES 20 02981752 1 PLATE, HITCH POST BOTTOM, MAVERICK 21 02964861 4 SHCS 3/4 NC 4" LG PL8 22 15B600 14 WASHER 3/8 SAE P 23 00003901 4 LOCKWASHER 3/4 HEAVY 24 00059700 14 FSCS 3/8 NC X 1-1/4 25 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 26 02892100 6 HHCS 3/4 NC X 1 3/4" LG 27 5312316 18 FLATWASHER 3/4 HARDENED 28 03200269 8 HHCS 3/4 NC 3 PL8 29 02984002 1 WLDMNT, STOP, SWIVEL

Page 16

50 IN ROTARY - BLADE BAR ASY

ITEM PART NO. QTY. DESCRIPTION

02982906 1 ASY, BLADE BAR W/BLADES 1 02982912 1 LEAF, MIDDLE, BLADE BAR 2 02982913 1 LEAF, BOTTOM, BLADE BAR 3 02962635 2 BLADE, CW ROTATION 4 02982934 1 WLDMT. TOP BLADE BAR 5 02782900 2 BOLT, BLADE 6 02957089 2 LOCKWASHER 1-1/8 PL STD 7 00020900 2 NUT, SLOTTED, HVY,1-1/8NF PL GR5 8 00023200 2 PIN, ROLL, 3/16X1-3/4 9 15C2000 4 WASHER, 1.375 X 2.50 X .165, HARDENED 10 02969235 2 HHCS, 1-1/4X3 PL GR8 11 02969236 2 HHCS, 1-1/4X2-1/4 PL GR8

Page 17

THIS PAGE INTENTIONAL LEFT BLANK

Page 18

50 IN ROTARY - BLADE PAN - HEAD ASY (SOLID MNT)

Page 19

50 IN ROTARY - BLADE PAN - HEAD ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986703 1 ASY, 50" ROT, PISTON, PAN 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 34 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981757 2 WELDMENT, PIN, HITCH POST 14 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 15 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 16 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 17 651102 1 PIN-DRILLED 18 02976448 1 PIN - MACHINED HEAD 19 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 20 02968837 1 PLASTIC TIE, YELLOW & WHITE 21 02968836 1 PLASTIC TIE, YELLOW 22 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90

Page 20

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SOLID MNT)

Page 21

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986703 1 ASY, 50" ROT, PISTON, PAN 1 00015800 34 LOCKNUT TLM 3/8 NC PLC 2 02891800 4 HHCS 1/2 NC 1-3/4 PL8 3 00019600 4 LOCKWASHER 1/2 HEAVY 4 02982907 2 SKID SHOE 5 02981411 1 WELDMENT, DECK 50" HEAD 6 02961038 1 GASKET 7 02964804 1 PAN ASSY 50" HEAD 8 02964861 4 SHCS 3/4 NC 4" LG PL8 9 15B600 14 WASHER 3/8 SAE P 10 00003901 4 LOCKWASHER 3/4 HEAVY 11 00059700 14 FSCS 3/8 NC X 1-1/4 12 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 13 03200269 8 HHCS 3/4 NC 3 PL8 14 02892100 8 HHCS 3/4 NC X 1 3/4" LG 15 00037200 16 NUT 3/4 NC LOCKNUT 16 5312316 16 FLATWASHER 3/4 HARDENED 17 02986200 1 WELDMENT, HITCH POST 18 02979881 1 MOTOR PISTON 4.91 CID 19 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 20 02968894 1 PLASTIC TIE, RED, 11LG 21 02968896 1 PLASTIC TIE, ORANGE, 11LG 22 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 23 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 24 00022200 8 LOCKWASHER 7/16 PL 25 02968895 1 PLASTIC TIE, BLUE, 11LG

Page 22

50 IN ROTARY - BLADE PAN - HEAD ASY (SWIVEL MNT)

Page 23

50 IN ROTARY - BLADE PAN - HEAD ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986198 1 ASY, 50" ROT, PISTON, PAN,SW 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 34 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 14 02981757 2 WELDMENT, PIN, HITCH POST 15 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 16 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 17 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 18 651102 1 PIN-DRILLED 19 02976448 1 PIN - MACHINED HEAD 20 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 21 03200267 1 HHCS 3/4 NC 5 PL8 22 02963646 3 HHCS 3/4 NC 2-1/2 PL8 23 00037200 18 NUT 3/4 NC LOCKNUT 24 02968837 1 PLASTIC TIE, YELLOW & WHITE 25 02968836 1 PLASTIC TIE, YELLOW 26 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 27 02968832 1 PLASTIC TIE, GREEN 28 02968833 1 PLASTIC TIE, GREEN & WHITE 29 03200762 2 ADP, HYD 6MB-4MJ 90 30 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 31 02968894 1 PLASTIC TIE, RED, 11LG 32 02968895 1 PLASTIC TIE, BLUE, 11LG 33 02968896 1 PLASTIC TIE, ORANGE, 11LG

Page 24

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SWIVEL MNT)

Page 25

50 IN ROTARY - BLADE PAN - HEAD SUB-ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986198 1 ASY, 50" ROT, PISTON, PAN,SW 1 00015800 34 LOCKNUT TLM 3/8 NC PLC 2 02963646 3 HHCS 3/4 NC 2-1/2 PL8 3 00037200 18 NUT 3/4 NC LOCKNUT 4 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 5 02891800 4 HHCS 1/2 NC 1-3/4 PL8 6 02979881 1 MOTOR PISTON 4.91 CID 7 00022200 8 LOCKWASHER 7/16 PL 8 00019600 4 LOCKWASHER 1/2 HEAVY 9 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 10 02980237 2 O-RING .139 DIA X 1.296 INSIDE 11 02982907 2 SKID SHOE 12 02981820 28 SHCS 1/2 NC X 1 1/2" LG PL8 13 02981318 1 SLEWING BEARING, 12 OD X 5.8 ID 14 02985319 1 WELDMENT, HITCH POST 15 02981411 1 WELDMENT, DECK 50" HEAD 16 02961038 1 GASKET 17 02964804 1 PAN ASSY 50" HEAD 18 02981752 1 PLATE, HITCH POST BOTTOM, MAVERICK 19 02964861 4 SHCS 3/4 NC 4" LG PL8 20 15B600 14 WASHER 3/8 SAE P 21 00003901 4 LOCKWASHER 3/4 HEAVY 22 00059700 14 FSCS 3/8 NC X 1-1/4 23 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 24 03200269 8 HHCS 3/4 NC 3 PL8 25 02892100 6 HHCS 3/4 NC X 1 3/4" LG 26 5312316 18 FLATWASHER 3/4 HARDENED 27 02984002 1 WLDMNT, STOP, SWIVEL

Page 26

50 IN ROTARY - BLADE PAN ASY

ITEM PART NO. QTY. DESCRIPTION

02964804 1 PAN ASSY 1 02964826 1 PAN,MACHINED 28.00 BC 2 02964828 1 SPIDER, MACHNED 28.00 BC 3 00755623 3 WASHER 2.200 OD1.218 1DX.250 4 00020900 3 NUT SLOT HVY 1-1/8 NF PL5 5 00023200 3 PIN ROLL 3/16X1-3/4 6 02964815 4 BUSHING, BLADE BOLT 7 02964954 3 KEY,5/16 SQ X 15/16 LONG 8 02965229 3 WASHER, 2-19/32 ID 5.0 OD 3/16 9 02964330 3 KEYED BLADE BOLT 10 02962722 1 BLADES-SET OF 3(50B/A HEAD) 11 7A16824 3 HHCS 1 NC 3 PL5 12 00748547 6 FLATWASHER 1-1/32 X 13 02964162 3 SPACER BLADE PAN WITH SPIDER 14 02030300 3 NUT TOPLOCK 1 NC PLB

Page 27

60 IN ROTARY - BLADE BAR ASY

ITEM PART NO. QTY. DESCRIPTION

02969230 1 BLADE BAR ASY, W/ BLADES 1 00020900 2 HEX SLOTTED NUT, HVY 1-1/8"-NF PL GR5 2 00023200 2 ROLL PIN, 3/16" X 1-3/4" 3 02969234 4 FLATWASHER, 1-1/4" HARDENED PL 4 02761500 1 BLADE SET, MATCHED SET OF TWO 5 02971387 1 LEAF BLADE BAR, TOP 6 02969232 1 LEAF BLADE BAR, MIDDLE 7 02969233 1 LEAF BLADE BAR, BOTTOM 8 02969235 2 BOLT, HEX HEAD 1-1/4"-NC X 3" PL GR8 9 02969236 2 BOLT, HEX HEAD 1-1/4"-NC X 2-1/4" PL GR8 10 02782900 2 BLADE BOLT, SHOULDERED 11 02957089 2 LOCKWASHER, 1-1/8" PL STD 12 00003901 4 LOCKWASHER, 3/4" PL HEAVY 13 02964861 4 BOLT, SOCKET HEAD 3/4"-NC X 4" PL GR8 14 02984572 1 BLADE BOLTS, NUTS, ROLLPIN KIT (INCLUDES 2 EACH OF ITEMS 1, 2, & 10)

Page 28

60 IN ROTARY - HEAD ASY (SOLID MNT)

Page 29

60 IN ROTARY - HEAD ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986205 1 ASY,60" ROT, PISTON, BAR 1 02971963 1 WELDMENT, DOOR 2 99338S 2 PIN ROLL 1/4 X 3/4 3 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 4 02981757 2 WELDMENT, PIN, HITCH POST 5 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 6 02967782 1 ROD-HINGE 7 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 8 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 9 651102 1 PIN - DRILLED 10 02976448 1 PIN - MACHINED HEAD 11 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 12 02885700 2 REAR FLAP 10 X 63 X 3/8 THK 13 02885800 1 REAR CLAMP BAR 14 00759862 2 DEBRIS DEFLECTOR 15 00756875 1 FLAP HOLD DOWN BAR 16 00023100 13 HHCS 3/8 X 1-1/2 NC PL GR5 17 00011100 46 FLATWASHER 3/8 STD 18 00015800 39 LOCKNUT TLM 3/8 NC PLC 19 00007000 12 HHCS 3/8 NC 1-3/4 PL5 20 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 21 02968836 1 PLASTIC TIE, YELLOW 22 02968837 1 PLASTIC TIE, YELLOW & WHITE

Page 30

60 IN ROTARY - HEAD SUB-ASY (SOLID MNT)

Page 31

60 IN ROTARY - HEAD SUB-ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986205 1 ASY,60" ROT, PISTON, BAR 1 02981410 1 WELDMENT,60" ROTARY,SWIVEL 2 02986200 1 WELDMENT, HITCH POST 3 02979881 1 MOTOR PISTON 4.91 CID 4 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 5 02969230 1 ASY, BLADE BAR W/BLADES 6 00015800 39 LOCKNUT TLM 3/8 NC PLC 7 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 8 02968894 1 PLASTIC TIE, RED, 11LG 9 02968896 1 PLASTIC TIE, ORANGE, 11LG 10 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 11 00022200 8 LOCKWASHER 7/16 PL 12 02968895 1 PLASTIC TIE, BLUE, 11LG 13 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 14 02891800 4 HHCS 1/2 NC 1-3/4 PL8 15 00019600 4 LOCKWASHER 1/2 HEAVY 16 02892100 8 HHCS 3/4 NC X 1 3/4" LG 17 00037200 16 NUT 3/4 NC LOCKNUT 18 5312316 16 FLATWASHER 3/4 HARDENED 19 02966899 2 SKID SHOE 20 02964861 4 SHCS 3/4 NC 4" LG PL8 21 00003901 4 LOCKWASHER 3/4 HEAVY 22 00059700 14 FSCS 3/8 NC X 1-1/4 23 15B600 14 WASHER 3/8 SAE P 24 02961038 1 GASKET 25 03200269 8 HHCS 3/4 NC 3 PL8 26 02980237 2 O-RING .139 DIA X 1.296 INSIDE

Page 32

60 IN ROTARY - HEAD ASY (SWIVEL MNT)

Page 33

60 IN ROTARY - HEAD ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986191 1 ASY, 60" ROT,PISTON,BAR,SWIVEL 1 02971963 1 WELDMENT, DOOR 2 99338S 2 PIN ROLL 1/4 X 3/4 3 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 4 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 5 02981757 2 WELDMENT, PIN, HITCH POST 6 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 7 02967782 1 ROD-HINGE 8 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 9 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 10 651102 1 PIN-DRILLED 11 02976448 1 PIN - MACHINED HEAD 12 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 13 03200267 1 HHCS 3/4 NC 5 PL8 14 02963646 3 HHCS 3/4 NC 2-1/2 PL8 15 00037200 18 NUT 3/4 NC LOCKNUT 16 02885700 2 REAR FLAP 10 X 63 X 3/8 THK 17 02885800 1 REAR CLAMP BAR 18 00759862 2 DEBRIS DEFLECTOR 19 00756875 1 FLAP HOLD DOWN BAR 20 00023100 13 HHCS 3/8 X 1-1/2 NC PL GR5 21 00011100 46 FLATWASHER 3/8 STD 22 00015800 32 LOCKNUT TLM 3/8 NC PLC 23 00007000 12 HHCS 3/8 NC 1-3/4 PL5 24 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 25 03200762 2 ADP, HYD 6MB-4MJ 90 26 02968836 1 PLASTIC TIE, YELLOW 27 02968837 1 PLASTIC TIE, YELLOW & WHITE 28 02968832 1 PLASTIC TIE, GREEN 29 02968833 1 PLASTIC TIE, GREEN & WHITE

Page 34

60 IN ROTARY - HEAD SUB-ASY (SWIVEL MNT)

Page 35

60 IN ROTARY - HEAD SUB-ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986191 1 ASY, 60" ROT,PISTON,BAR,SWIVEL 1 02981410 1 WELDMENT,60" ROTARY,SWIVEL 2 02985319 1 WELDMENT, HITCH POST 3 02979881 1 MOTOR PISTON 4.91 CID 4 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 5 02969230 1 ASY, BLADE BAR W/BLADES 6 02963646 3 HHCS 3/4 NC 2-1/2 PL8 7 00037200 18 NUT 3/4 NC LOCKNUT 8 02972817 1 ADP HYD ELBOW 10MB - 8MJ 45 DEG 9 00015800 32 LOCKNUT TLM 3/8 NC PLC 10 02968894 1 PLASTIC TIE, RED, 11LG 11 02968895 1 PLASTIC TIE, BLUE, 11LG 12 02968896 1 PLASTIC TIE, ORANGE, 11LG 13 02892100 6 HHCS 3/4 NC X 1 3/4" LG 14 5312316 18 FLATWASHER 3/4 HARDENED 15 00019600 4 LOCKWASHER 1/2 HEAVY 16 02984002 1 WLDMNT, STOP, SWIVEL 17 02891800 4 HHCS 1/2 NC 1-3/4 PL8 18 02980237 2 O-RING .139 DIA X 1.296 INSIDE 19 00022200 8 LOCKWASHER 7/16 PL 20 02980236 8 HHCS 7/16 NC X 4 1/2"LG PL5 21 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 22 15B600 7 WASHER 3/8 SAE P 23 00059700 7 FSCS 3/8 NC X 1-1/4 24 00003901 4 LOCKWASHER 3/4 HEAVY 25 02961038 1 GASKET 26 02966899 1 SKID SHOE 27 02964861 4 SHCS 3/4 NC 4" LG PL8 28 03200269 8 HHCS 3/4 NC 3 PL8 29 02981752 1 PLATE, HITCH POST BOTTOM, MAVERICK 30 02981820 13 SHCS 1/2 NC X 1 1/2" LG PL8 31 02981318 1 BEARING, 12OD X 5.8ID

Page 36

ROTARY - MOTOR AND SPINDLE ASY

ITEM PART NO. QTY. DESCRIPTION

1 02979881 1 MOTOR ASY, PISTON TYPE 4.91 CID 2 02968859A 1 SPINDLE & HOUSING ASY, SPLINED 3 02961038 1 GASKET-SPINDLE/MOTOR 4 02981819 2 ADP HYD STGHT 16FLH-16MJ SPCL 5 02980237 2 O-RING 6 02972817 1 HYD ELBOW, 10MB - 8MJ45 7 02980236 8 BOLT 8 00022200 8 LOCKWASHER, STD 7/16" PL 9 02891800 4 BOLT, HEX HEAD 1/2"-NC X 1-3/4" PL GR8 10 00019600 4 LOCKWASHER, 1/2" HEAVY

Page 37

THIS PAGE INTENTIONAL LEFT BLANK

Page 38

ROTARY - MOTOR ASY (PART 1)

Page 39

ROTARY - MOTOR ASY (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

02979881 1 MOTOR ASY, PISTON TYPE 4.91 CID 1 02980529 1 BARREL HOUSING ASY 2 02980530 1 VALVE PLATE 4 02980536 1 NOZZLE PLUG 2.5MM 5 02980537 1 PLUG ASY, 7/8" HEXAGON 6 02980538 1 BEARING HOUSING 7 02980539 1 O-RING, 132 X 3 8 02980540 1 O-RING, 104.5 X 3 9 02980541 1 SEAL CARRIER 10 02980542 1 SHAFT SEAL 11 02980543 1 SPACER WASHER 12 02980544 1 RETAINING RING 13 02980545 1 RETAINING RING 14 02980546 1 SHAFT ASY, TYPE U 15 02980548 1 CYLINDER BARREL 16 02980549 1 BARREL SUPPORT 17 02980550 7 PISTON ASY 18 02980551 21 PISTON RING 19 02980552 1 RING GEAR 20 02980553 1 TAP ROL BEARING 21 02980554 1 BEARING, TAPERED ROLLER 22 02980555 1 SPACER WASHER 23 02980556 1 RETAINING RING 24 02980557 1 SHIM, 0.5

02980558 1 SHIM, 0.2

02980559 1 SHIM, 0.4

02980560 1 SHIM, 0.6

02980561 1 SHIM, 0.8

02980562 1 SHIM, 1.0

02980563 1 SHIM, 0.7 25 02980564 4 BOLT, SOCKET HEAD M12 X 50 10.9 26 02980565 1 LOCKWASHER, M13 X 19.5 27 02980547 1 GUIDE PIN 28 02980571 1 RELIEF MANIFOLD

02980570 1 RELIEF VALVE, SEAL KIT 29 02980568 1 RELIEF VALVE, 280 BAR 30 02980569 1 RELIEF VALVE, 330 BAR 31 02980237 2 O-RING 32 02980531 1 KEY, FLAT 33 02980532 2 STEEL BALL 34 02980533 2 PLUG, HEXAGON

Page 40

ROTARY - MOTOR ASY (PART 2)

Page 41

ROTARY - MOTOR ASY (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

35 02980534 2 O-RING 36 02980535 2 PLUG ASY, HEX SOCKET 37 02980572 2 PLUG ASY 38 02980573 1 PLUG ASY 39 02980566 1 REBUILD KIT 40 02980567 1 SEAL KIT, FOR 02979881 MTR

Page 42

ROTARY - SPINDLE ASY

Page 43

ROTARY - SPINDLE ASY

Continued... ITEM PART NO. QTY. DESCRIPTION

02968859 1 SPINDLE ASY 1 02967204 1 SPINDLE SHAFT, SPLINED 2 02967126 1 HOUSING, MACHINED SPINDLE 3 02967197 1 BEARING ASY, CUP & CONE, LOWER 4 02967196 1 BEARING ASY, CUP & CONE, UPPER 5 02909500 2 ADJUSTING NUT, 2.360-18 PITCH 6 02909600 1 TABBED LOCKWASHER, BEARING ADJUSTING NUT LOCK 7 02967198 1 SEAL 8 02959018 1 GREASE RELIEF FITTING, 1-5LBS 9 00003500 1 GREASE FITTING, 1/8" STRAIGHT

Page 44

BOOM ASY - 18 FT BOOM (PART 1)

Page 45

BOOM ASY - 18 FT BOOM (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986858 1 ASY, 18 BOOM, PISTON 1 02986896 1 WELDMENT,18` LIFT 2 02983707 1 WELDMENT, DIPPER, 18` 3 02981279 1 CYLINDER, 4.0B X 2.25R X 24.63S 4 02984944 1 CYLINDER, 3.5B X 1.5R X 16.0S 5 02983320 1 CYL, 3.5B X 1.5R X 30.0S 6 02971751 1 PIN, 1-1/2 X 5-3/16 & 13/32 HOLE 7 02981294 1 WELDMENT, PIN, LIFT/ DIPPER 8 02982981 1 WELDMENT, CYLINDER PIN LONG, NEW BOOM 9 02981420 2 CONNEX BUSHING, 2 1/4 X 2 X 3 10 02981424 8 CONNEX BUSHING, 1 3/4 X 1 1/2 X 3 11 02981273 1 SPACER, PIN, DIPPER, MAVERICK 12 02981702 1 SLOTTED NUT, 1-1/2 NF 13 02984819 1 HYDRAULIC TUBE, #16 14 02984818 1 HYDRAULIC TUBE, #12 15 02984817 1 HYDRAULIC TUBE, #16 16 02985273 1 ASSEMBLY, TILT CYLINDER COVER 17 02965448 4 ADP, HYD 4MJ -4MJ BULKHEAD 18 02919600 4 CAP, HYD 4FJ 19 165020 1 PIN, COTTER 5/16 X 2-1/2 PL 20 63149100 3 ADP, HYD ELBOW 6MB-6MJ 90 21 00002700 3 FLATWASHER, 1/2 PL STD 22 02975436 1 HHCS 1/2 NC X 2 1/4 PL8 23 00001800 1 LOCKNUT TLM 1/2 NC PLB 24 00023100 3 HHCS 3/8 X 1-1/2 NC PL GR5 25 02970595 1 HHCS 3/8 NC 2-3/4 PL8 26 00015800 4 LOCKNUT TLM 3/8 NC PLC 27 001921 1 ADAPTER 6MJ - 6FJX 90 28 000941 1 GREASE ZERK 1/4-28 90 BOLT THD 29 00752670 8 GREASE FITTING 1/4-28 BOLT THD 30 02968835 1 PLASTIC TIE, ORANGE & WHITE 31 02968831 1 PLASTIC TIE, BLUE & WHITE 32 02968834 1 PLASTIC TIE, ORANGE 33 02968830 1 PLASTIC TIE, BLUE 34 02968829 1 PLASTIC TIE, RED & WHITE 35 02968828 1 PLASTIC TIE, RED 36 02968837 1 PLASTIC TIE, YELLOW & WHITE 37 02968836 1 PLASTIC TIE, YELLOW 38 02968894 4 PLASTIC TIE, RED, 11LG 39 02968896 4 PLASTIC TIE, ORANGE, 11LG 40 02968895 4 PLASTIC TIE, BLUE, 11LG

Page 46

BOOM ASY - 18 FT BOOM (PART 2)

Page 47

BOOM ASY - 18 FT BOOM (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

41 02968832 1 PLASTIC TIE, GREEN 42 02968833 1 PLASTIC TIE, GREEN & WHITE 43 02984821 1 COVER, LIFT TUBE COVER 44 02956918 2 CAP, 16 FJ 45 03200375 4 CLAMP, TUBE 1-POSTION 46 02984868 2 CLAMP, TUBE 1-POSTION, 3/4" 47 02985222 2 PLATE, LINKAGE 48 02986074 1 WELDMENT, LINKAGE 49 02985220 3 WELDMENT, PIN, LINKAGE 50 00011400 3 BOLT, HHCS 3/8 NC 1 PL5 51 00769258 3 RETAINING RING,1.5 SHAFT 52 02982979 2 WELDMENT, CYLINDER PIN, NEW BOOM 53 0381000 2 CARB 1/2 - 13 X 2.75 54 00019600 2 LOCKWASHER 1/2 HEAVY 55 02983080 2 NUT, 1/2-13 ACORN 56 63161900 2 SPRING NUT 1/2 57 02985978 1 PLATE, BULKHEAD 58 000860 4 BOLT, HHCS 1/4" X 7/8" LG 59 00751846 3 ADP HYD STGHT 16MJ - 16MJ BULKHEAD 60 02985976 1 ADP HYD STGHT 12MJ - 12MJ BULKHEAD 61 02976532 2 ADP, HYD, 4MJ-4FJX 45 62 02962022 2 ADP HYD ELBOW 4MJ-4FJX90 63 02956851 1 ADP HYD ELBOW 16 MJ-16 JX 90 64 02981197 1 ADAPTER 12MJ - 12MJ 90 BULKHEAD 65 02972910 1 CAP, #8 FJ 66 02742500 1 ADAPTER 16MJ - 16MJ 90 BULKHEAD 67 03101646 3 LOCKWASHER 3/8 68 00024100 4 FLATWASHER STD 1/4 PL 69 00024000 4 NUT HEX 1/4" NC PL 70 02970609 1 ADP 12FJ - 8MJ

Page 48

BOOM ASY - 22 FT BOOM (PART 1)

Page 49

BOOM ASY - 22 FT BOOM (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986859 1 ASY, 22 BOOM, PISTON 1 02986897 1 WELDMENT,LIFT SECTION 22` BOOM 2 02985124 1 WELDMENT, 22` DIPPER 3 02981294 1 WELDMENT, PIN, LIFT/ DIPPER 4 02981279 1 CYLINDER, 4.0B X 2.25R X 24.63S 5 02982979 3 WELDMENT, CYLINDER PIN, NEW BOOM 6 02982980 1 WELDMENT, CYLINDER PIN SHORT, NEW BOOM 7 02981273 1 SPACER, PIN, DIPPER, MAVERICK 8 02981277 1 CYLINDER, 4.0B X 2.25R X 21.5S 9 02981702 1 SLOTTED NUT, 1-1/2 NF 10 63149100 3 ADP, HYD ELBOW 6MB-6MJ 90 11 02981420 2 CONNEX BUSHING, 2 1/4 X 2 X 3 12 02981424 8 CONNEX BUSHING, 1 3/4 X 1 1/2 X 3 13 02984853 1 HYDRAULIC TUBE, #16 14 02984854 1 HYDRAULIC TUBE, #12 15 02984855 1 HYDRAULIC TUBE, #16 16 02965448 4 ADP, HYD 4MJ -4MJ BULKHEAD 17 02919600 4 CAP, HYD 4FJ 18 00002700 5 FLATWASHER, 1/2 PL STD 19 02975436 1 HHCS 1/2 NC X 2 1/4 PL8 20 00001800 1 LOCKNUT TLM 1/2 NC PLB 21 02957042 1 HHCS 3/8NC 1-3/4 PL GR8 22 00023100 3 HHCS 3/8 X 1-1/2 NC PL GR5 23 00015800 4 LOCKNUT TLM 3/8 NC PLC 24 00752670 10 GREASE FITTING 1/4-28 BOLT THD 25 000941 1 GREASE ZERK 1/4-28 90 BOLT THD 26 02968835 1 PLASTIC TIE, ORANGE & WHITE 27 165020 1 PIN, COTTER 5/16 X 2-1/2 PL 28 02968834 1 PLASTIC TIE, ORANGE 29 02968831 1 PLASTIC TIE, BLUE & WHITE 30 02968830 1 PLASTIC TIE, BLUE 31 02968829 1 PLASTIC TIE, RED & WHITE 32 02968828 1 PLASTIC TIE, RED 33 02968837 1 PLASTIC TIE, YELLOW & WHITE 34 02968836 1 PLASTIC TIE, YELLOW 35 02968894 4 PLASTIC TIE, RED, 11LG 36 02968896 4 PLASTIC TIE, ORANGE, 11LG 37 001921 1 ADAPTER 6MJ - 6FJX 90 38 02968832 1 PLASTIC TIE, GREEN 39 02968833 1 PLASTIC TIE, GREEN & WHITE 40 03200375 8 CLAMP, TUBE 1-POSTION

Page 50

BOOM ASY - 22 FT BOOM (PART 2)

Page 51

BOOM ASY - 22 FT BOOM (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

41 02968895 4 PLASTIC TIE, BLUE, 11LG 42 02984856 1 COVER, LIFT TUBE COVER 43 02984857 1 COVER, LIFT TUBE COVER 44 02984868 4 CLAMP, TUBE 1-POSTION, 3/4" 45 02956918 2 CAP, 16 FJ 46 00011400 3 BOLT, HHCS 3/8 NC 1 PL5 47 00769258 3 RETAINING RING,1.5 SHAFT 48 02986074 1 WELDMENT, LINKAGE 49 02985220 3 WELDMENT, PIN, LINKAGE 50 02985222 2 PLATE, LINKAGE 51 02985273 1 ASSEMBLY, TILT CYLINDER COVER 52 02984944 1 CYLINDER, 3.5B X 1.5R X 16.0S 53 0381000 4 CARB 1/2 - 13 X 2.75 54 00019600 4 LOCKWASHER 1/2 HEAVY 55 02983080 4 NUT, 1/2-13 ACORN 56 63161900 4 SPRING NUT 1/2 57 02972910 1 CAP, #8 FJ 58 00751846 3 ADP HYD STGHT 16MJ - 16MJ BULKHEAD 59 02985976 1 ADP HYD STGHT 12MJ - 12MJ BULKHEAD 60 02981197 1 ADAPTER 12MJ - 12MJ 90 BULKHEAD 61 02742500 1 ADAPTER 16MJ - 16MJ 90 BULKHEAD 62 02956851 1 ADP HYD ELBOW 16 MJ-16 JX 90 63 02962022 2 ADP HYD ELBOW 4MJ-4FJX90 64 02976532 2 ADP, HYD, 4MJ-4FJX 45 65 02985978 1 PLATE, BULKHEAD 66 000860 4 BOLT, HHCS 1/4" X 7/8" LG 67 02970609 1 ADP 12FJ - 8MJ 68 03101646 3 LOCKWASHER 3/8 69 00024000 4 NUT HEX 1/4" NC PL 70 00024100 4 FLATWASHER STD 1/4 PL

Page 52

BOOM ASY - 25 FT BOOM (PART 1)

Page 53

BOOM ASY - 25 FT BOOM (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986860 1 25 FT BOOM ASY 1 02986898 1 WELDMENT, 25` LIFT 2 02984895 1 WELDMENT, 25` DIPPER 3 02981279 1 CYLINDER, 4.0B X 2.25R X 24.63S 4 02981277 1 CYLINDER, 4.0B X 2.25R X 21.5S 5 02981420 2 CONNEX BUSHING, 2 1/4 X 2 X 3 6 02981424 8 CONNEX BUSHING, 1 3/4 X 1 1/2 X 3 7 02981294 1 WELDMENT, PIN, LIFT/ DIPPER 8 02981273 1 SPACER, PIN, DIPPER, MAVERICK 9 02981702 1 SLOTTED NUT, 1-1/2 NF 10 02982979 3 WELDMENT, CYLINDER PIN, NEW BOOM 11 02982980 1 WELDMENT, CYLINDER PIN SHORT, NEW BOOM 12 02965448 4 ADP, HYD 4MJ -4MJ BULKHEAD 13 02919600 4 CAP, HYD 4FJ 14 63149100 3 ADP, HYD ELBOW 6MB-6MJ 90 15 00002700 5 FLATWASHER, 1/2 PL STD 16 02975436 1 HHCS 1/2 NC X 2 1/4 PL8 17 00001800 1 LOCKNUT TLM 1/2 NC PLB 18 02957042 1 HHCS 3/8NC 1-3/4 PL GR8 19 00023100 3 HHCS 3/8 X 1-1/2 NC PL GR5 20 00015800 4 LOCKNUT TLM 3/8 NC PLC 21 000941 1 GREASE ZERK 1/4-28 90 BOLT THD 22 00752670 10 GREASE FITTING 1/4-28 BOLT THD 23 165020 1 PIN, COTTER 5/16 X 2-1/2 PL 24 02968835 1 PLASTIC TIE, ORANGE & WHITE 25 02968834 1 PLASTIC TIE, ORANGE 26 02968831 1 PLASTIC TIE, BLUE & WHITE 27 02968830 1 PLASTIC TIE, BLUE 28 02968828 1 PLASTIC TIE, RED 29 02968829 1 PLASTIC TIE, RED & WHITE 30 02968836 1 PLASTIC TIE, YELLOW 31 02968837 1 PLASTIC TIE, YELLOW & WHITE 32 02968894 4 PLASTIC TIE, RED, 11LG 33 02968896 4 PLASTIC TIE, ORANGE, 11LG 34 001921 1 ADAPTER 6MJ - 6FJX 90 35 02968832 1 PLASTIC TIE, GREEN 36 02968833 1 PLASTIC TIE, GREEN & WHITE 37 03200375 8 CLAMP, TUBE 1-POSTION 38 02984868 4 CLAMP, TUBE 1-POSTION, 3/4" 39 02984890 1 HYDRAULIC TUBE, #16 40 02984891 1 HYDRAULIC TUBE, #12

Page 54

BOOM ASY - 25 FT BOOM (PART 2)

Page 55

BOOM ASY - 25 FT BOOM (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

41 02984892 1 HYDRAULIC TUBE, #16 42 02968895 4 PLASTIC TIE, BLUE, 11LG 43 02984893 1 COVER, LIFT TUBE COVER 44 02984894 1 COVER, LIFT TUBE COVER 45 02956918 2 CAP, 16 FJ 46 02983080 4 NUT, 1/2-13 ACORN 47 00019600 4 LOCKWASHER 1/2 HEAVY 48 0381000 4 CARB 1/2 - 13 X 2.75 49 63161900 4 SPRING NUT 1/2 50 02985222 2 PLATE, LINKAGE 51 02985220 3 WELDMENT, PIN, LINKAGE 52 00769258 3 RETAINING RING,1.5 SHAFT 53 02985273 1 ASSEMBLY, TILT CYLINDER COVER 54 02984944 1 CYLINDER, 3.5B X 1.5R X 16.0S 55 02986074 1 WELDMENT, LINKAGE 56 00011400 3 BOLT, HHCS 3/8 NC 1 PL5 57 02976532 2 ADP, HYD, 4MJ-4FJX 45 58 00751846 3 ADP HYD STGHT 16MJ - 16MJ BULKHEAD 59 02956851 1 ADP HYD ELBOW 16 MJ-16 JX 90 60 02962022 2 ADP HYD ELBOW 4MJ-4FJX90 61 02981197 1 ADAPTER 12MJ - 12MJ 90 BULKHEAD 62 02972910 1 CAP, #8 FJ 63 02742500 1 ADAPTER 16MJ - 16MJ 90 BULKHEAD 64 02985978 1 PLATE, BULKHEAD 65 02985976 1 ADP HYD STGHT 12MJ - 12MJ BULKHEAD 66 000860 4 BOLT, HHCS 1/4" X 7/8" LG 67 03101646 3 LOCKWASHER 3/8 68 02970609 1 ADP 12FJ - 8MJ 69 00024100 4 FLATWASHER STD 1/4 PL 70 00024000 4 NUT HEX 1/4" NC PL

Page 56

COMMON CRATE COMPONENTS

Page 57

COMMON CRATE COMPONENTS

Continued... ITEM PART NO. QTY. DESCRIPTION

02987499 1 PACKET, INST DWGS AND DECALS

02981441 2 KNOB 3/8NC X 1-1/2 STUD

02987829 1 ASSEMBLY JOYSTICK CONSOLE

00776031 1 CANISTER, PARTS MANUAL

02966874 1 BOOT,CABLE

02986941A 1 ASSEMBLY OPERATORS & PARTS

02986941CA 1 ASSEMBLY CANISTER MANUAL

02987401 1 ASY, COMPLETE, TANK & VALVE

02986111 1 CABLE, PUMP COVER 36

02986130 1 CABLE, MANUAL CANISTER, 24

02970116 2 TUBE,FRAME MOUNTING

02753400 2 PLASTIC TIE 15 LG UV BLACK

02975004 1 MOUNT TIE ROD

02984735 1 ASY, HARNESS, MACHETE

02966639 6 BAR,MOUNT STRAP

02981381 1 ASY, PUMP COVER

02987727 1 BOOM TO FRAME HOSE BUNDLE

02987705 3 BAR,MOUNT STRAP 4-1/2

Page 58

DECALS - 18-22-25 FT BOOM

ITEM PART NO. QTY. DESCRIPTION

43 02962764 6 DECAL, PINCH POINT 59 02985831 2 DECAL, MACHETE 2 18`

02984939 2 DECAL, MACHETE 2 22`

02984940 2 DECAL, MACHETE 2 25`

Page 59

DECALS - 50 & 60 IN ROTARY HEAD

ITEM PART NO. QTY. DESCRIPTION

1 00757139 2 DECAL, LOGO (ALAMO BY T.K.) 2 00757140 1 DECAL, ALAMO INDUSTRIAL LOGO 3 00769736 1 DECAL, USE/REPAIR GUARDS 4 00769737 2 DECAL, BLADES THROWN OBJECTS 5 02925100 1 DECAL, REPLACEMENT PARTS 6 02967827 1 DECAL, MULTI HAZARD 7 02967867 1 DECAL, DANGER SAFETY SHIELD 8 2738332 1 DECAL, RED OBLONG REFLECTOR 9 2738333 1 DECAL, YELLOW OBLONG REFLECTOR 10 02986679 1 PLATE S/N 50", ROTARY, PISTON

02986112 1 PLATE S/N 60", ROTARY, PISTON 11 3710151 4 METAL TACK 12 02982927 1 DECAL, 50 ROTARY

02970889 1 DECAL, 60 ROTARY

Page 60

DECALS - HYD TANK AND PUMP

ITEM PART NO. QTY. DESCRIPTION

1 02982828 1 DECAL, TEMP RANGE 2 02971943 1 DECAL, LOGO RECT CLEAR Y/W, 2 7/8 X 20 3 02965262 1 DECAL - WARNING - HOSE BURST 4 02971123 1 DECAL WARNING PRESS TANK 5 02987402 1 DECAL, VALVE LAYOUT M2

Page 61

FILTER ASY

ITEM PART NO. QTY. DESCRIPTION

02985828 1 FILTER, RETURN 1 02981713 1 HEAD, FILTER RTB30 2 02981714 1 COVER, FILTER 3 02981715 1 SPRING, FILTER, ASY 4 02981716 1 KIT, SEAL, FILTER, RETURN 5 02981717 1 ELEMENT, FILTER, RETURN 6 02981718 1 BOWL, FILTER, RETURN 7 02981719 1 GUARD, FILTER, RETURN 8 02981720 1 BREATHER, ELEMENT, FILTER 9 02981721 1 COVER, BREATHER, FILTER 10 02987302 1 INDICATOR, FILTER BYPASS

Page 62

HIGH FRAME MOUNT ASY - 2WD

Page 63

HIGH FRAME MOUNT ASY - 2WD

Continued... ITEM PART NO. QTY. DESCRIPTION

02978449 1 ASY HIGH FRAME 2WD 1 02978447 1 WELDMENT FRAME 2WD 2 02978000 1 SUB-ASY KINGPOST FRAME 3 02978461 1 WLDMT PIN 1-1/2 OD X 6-3/4 LG CHROMED 4 02975596 1 TUBE SPACER 3/4 OD X .51 ID X .31 LG 5 00013300 1 HHCS 1/2 NC 2 PL5 6 00002700 1 FLATWASHER 1/2 PL STD 7 00001800 1 LOCKNUT 1/2 NC PLB 8 02960521 8 HHCS 3/4 NC 2-3/4 PL8 9 00037200 8 LOCKNUT 3/4 NC PLC 10 5312316 16 WASHER 25/32 X 1-7/16 X 1/8 HARDENED 11 02968841 1 ASSEMBLY LIFT CYLINDER 12 00725746 1 DECAL SPANISH TRANSL 13 02742500 3 ELBOW 16MJ -16MJ90 BULKHEAD 14 02962765 1 DECAL MULTI-HAZZARD 15 02965262 1 DECAL HOSE BURST

Page 64

HIGH FRAME MOUNT ASY - 4WD

Page 65

HIGH FRAME MOUNT ASY - 4WD

Continued... ITEM PART NO. QTY. DESCRIPTION

02978450 1 ASY HIGH FRAME 4WD 1 02978448 1 WELDMENT FRAME 4WD 2 02978000 1 SUB-ASY KINGPOST FRAME 3 02978461 1 WLDMT PIN 1-1/2 OD X 6-3/4 LG CHROMED 4 02975596 1 TUBE SPACER 3/4 OD X .51 ID X .31 LG 5 00013300 1 HHCS 1/2 NC 2 PL5 6 00002700 1 FLATWASHER 1/2 PL STD 7 00001800 1 LOCKNUT 1/2 NC PLB 8 02960521 8 HHCS 3/4 NC 2-3/4 PL8 9 00037200 8 LOCKNUT 3/4 NC PLC 10 5312316 16 WASHER 25/32 X 1-7/16 X 1/8 HARDENED 11 02968841 1 ASSEMBLY LIFT CYLINDER 12 00725746 1 DECAL SPANISH TRANSL 13 02742500 3 ELBOW 16MJ -16MJ90 BULKHEAD 14 02962765 1 DECAL MULTI-HAZZARD 15 02965262 1 DECAL HOSE BURST

Page 66

HIGH FRAME MOUNT SUB-ASY

Page 67

HIGH FRAME MOUNT SUB-ASY

Continued... ITEM PART NO. QTY. DESCRIPTION

02978000 1 SUB-ASSEMBLY KINGPOST FRAME 1 02975491 1 MOUNTING KINGPOST MACHINED 2 02968840 1 ASSY,SWING CYLINDER 3 02975508 1 PIN 2-1/2 OD X 20-11/16 LONG 4 02975493 1 KINGPOST MACHINED 5 02987739 2 BUSHING CONNEX 1-3/4 X1 -1/2X3 6 02978477 1 WLDMT PIN 1-1/2 X 3-9/16 LG 7 00748823 2 HHCS 1/2-13UNC 1-1/2 PL5 8 02975596 2 TUBE SPACER 3/4 OD X .51 ID X 9 00002700 2 FLATWASHER 1/2 PL STD 10 00001800 3 LOCKNUT TLM 1/2 NC PLB 11 02966088 1 WASHER,THRUST-5OD X 2-9/16ID 12 02978476 1 WLDMT PIN 1-1/2 OD X 6 LG 13 02987636 2 BUSHING CONNEX 2-3/4 X2 -1/2X2 14 02956765 1 HHCS 1/2 NC 4-1/2 PL8 15 02963646 1 HHCS 3/4 NC 2-1/2 PL8 16 02023900 1 NUT 3/4 NC HEX PL JAM 17 02975429 1 SNAP RING INTERNAL 2.775 DIA X 18 00752670 3 FITTING,GREASE STRAIGHT 1/4-28

Page 68

HOSE ROUTING - 18 FT BOOM

Page 69

HOSE ROUTING - 18 FT BOOM NOTES

ITEM PART NO. QTY. DESCRIPTION

1 02983346 1 HOSE #6-6FJX-6MJ-61LG 2 02983347 1 HOSE #6-6FJX-6MJ-61LG 3 02983348 1 HOSE #4-4FJX-4MJ-61LG 4 02983349 1 HOSE #4-4FJX-4MJ-61LG 5 02983531 1 HOSE #4-4FJX-4MJ-61LG 6 02983532 1 HOSE #4-4FJX-4MJ-61LG 7 02983350 1 HOSE #6-6FJX-6MJ-124LG 8 02983351 1 HOSE #6-6FJX-6MJ-124LG 9 02983352 1 HOSE #4-4FJX-4MJ-116LG 10 02983353 1 HOSE #4-4FJX-4MJ-116LG 11 02983533 1 HOSE #4-4FJX-4MJ-116LG 12 02983534 1 HOSE #4-4FJX-4MJ-116LG 13 02984267 1 HOSE #6-6FJX-6MJ-36LG 14 02984268 1 HOSE #6-6FJX-6MJ-36LG 15 02984833 1 HOSE #16-16FJX-16FJX45-54LG 16 02984834 1 HOSE #16-16FJX-16FJX45-58-1/2 17 02984835 1 HOSE #12-12FJX-12FJX45-60-1/2 18 02986007 1 HOSE #16-16FJX-16FJX90-62-1/2 19 02986008 1 HOSE #16-16FJX-16FJX90-58-3/4 20 02986009 1 HOSE #12-12FJX-12FJX-60-1/8 21 02961085 1 CORDURA SLEEVING-54 LG 22 02982334 1 CORDURA SLEEVE, 2.54ID, 10LG 23 02983079 1 SLEEVE 66" CORDURA 2.54 ID 24 02986797 1 CORDURA SLEEVE, 2.54ID, 14LG

Page 70

HOSE ROUTING - 22 FT BOOM

Page 71

HOSE ROUTING - 22 FT BOOM NOTES

ITEM PART NO. QTY. DESCRIPTION

1 02983178 1 HOSE #6-6FJX-6MJ-108LG 2 02983179 1 HOSE #6-6FJX-6MJ-108LG 3 02983180 1 HOSE #6-6FJX-6MJ-94LG 4 02983181 1 HOSE #6-6FJX-6MJ-94LG 5 02983182 1 HOSE #4-4FJX-4MJ-94LG 6 02983183 1 HOSE #4-4FJX-4MJ-94LG 7 02983503 1 HOSE #4-4FJX-4MJ-94LG 8 02983504 1 HOSE #4-4FJX-4MJ-94LG 9 02983184 1 HOSE #6-6FJX-6MJ-140LG 10 02983185 1 HOSE #6-6FJX-6MJ-140LG 11 02983186 1 HOSE #4-4FJX-4MJ-140LG 12 02983187 1 HOSE #4-4FJX-4MJ-140LG 13 02983499 1 HOSE #4-4FJX-4MJ-140LG 14 02983500 1 HOSE #4-4FJX-4MJ-140LG 15 02986107 1 HOSE #16-16FJX-16FJX-62LG 16 02986108 1 HOSE #16-16FJX-16FJX-62LG 17 02986109 1 HOSE #12-12FJX-12FJX-62LG 18 02986004 1 HOSE #16-16FJX-16FJX90-69-7/8 19 02986005 1 HOSE #16-16FJX-16FJX90-65-1/2 20 02986006 1 HOSE #12-12FJX-12FJX90-69-1/8 21 02986798 1 CORDURA SLEEVE, 3.66ID, 58LG 22 02982334 1 CORDURA SLEEVE, 2.54ID, 10LG 23 02983079 1 SLEEVE 66" CORDURA 2.54 ID 24 02986797 1 CORDURA SLEEVE, 2.54ID, 14LG

Page 72

HOSE ROUTING - 25 FT BOOM

Page 73

HOSE ROUTING - 25 FT BOOM NOTES

ITEM PART NO. QTY. DESCRIPTION

1 02983188 1 HOSE #6-6FJX-6MJ-126LG 2 02983189 1 HOSE #6-6FJX-6MJ-126LG 3 02983190 1 HOSE #6-6FJX-6MJ-102LG 4 02983191 1 HOSE #6-6FJX-6MJ-102LG 5 02983192 1 HOSE #4-4FJX-4MJ-102LG 6 02983193 1 HOSE #4-4FJX-4MJ-102LG 7 02983505 1 HOSE #4-4FJX-4MJ-102LG 8 02983506 1 HOSE #4-4FJX-4MJ-102LG 9 02983194 1 HOSE #6-6FJX-6MJ-158LG 10 02983195 1 HOSE #6-6FJX-6MJ-158LG 11 02983196 1 HOSE #4-4FJX-4MJ-158LG 12 02983197 1 HOSE #4-4FJX-4MJ-158LG 13 02983501 1 HOSE #4-4FJX-4MJ-158LG 14 02983502 1 HOSE #4-4FJX-4MJ-158LG 15 02986107 1 HOSE #16-16FJX-16FJX-62LG 16 02986108 1 HOSE #16-16FJX-16FJX-62LG 17 02986109 1 HOSE #12-12FJX-12FJX-62LG 18 02986001 1 HOSE #16-16FJX-16FJX90-88 19 02986002 1 HOSE #16-16FJX-16FJX90-83-5/8 20 02986003 1 HOSE #12-12FJX-12FJX90-87-1/4 22 02986798 1 CORDURA SLEEVE, 3.66ID, 58LG 23 02982334 1 CORDURA SLEEVE, 2.54ID, 10LG 24 02983079 1 SLEEVE 66" CORDURA 2.54 ID 25 02986810 1 CORDURA SLEEVE, 3.66ID, 76LG 26 02986797 1 CORDURA SLEEVE, 2.54ID, 14LG

Page 74

HOSE ROUTING - HYDRAULIC KIT

Page 75

HOSE ROUTING - HYDRAULIC KIT

Continued... ITEM PART NO. QTY. DESCRIPTION

1 02981427 1 HOSE #8-8FJX-8FJX90-24LG 2 02981428 1 HOSE #8-8FJX-8FJX90-21LG 3 02981429 1 HOSE #12-12FJX-12FJX-23LG 4 02986726 1 HOSE #12-12FJX-12FJX90-24LG 5 02981431 1 HOSE #4-4FJX-4FJX90-35LG 6 02981432 1 HOSE #4-4FJX-4FJX90-20LG 7 02981433 1 HOSE #20-20FJX-20FJX-24LG 8 02987742 1 HOSE #12-12FJX-12FJX 36LG 9 02823600 1 HOSE #4 - 4FJX - 4FJX - 28LG

Page 76

HYDARULIC CYLINDER ASY - DIPPER 22-25 FT BOOM

ITEM PART NO. QTY. DESCRIPTION

02981277 1 HYD CYL ASY, 4" BORE X 21.5" STROKE (22 & 25 FT BOOM) 1 02981925 1 BARREL WLDMT 2 02981926 1 ROD WLDMT 3 02982250 2 BUSHING, ROD END 1-1/2" LG 4 02982251 2 BUSHING, BARREL END 2" LG 5 02982068 1 SEAL KIT

Page 77

HYDARULIC CYLINDER ASY - LIFT BOOM

ITEM PART NO. QTY. DESCRIPTION

02981279 1 CYLINDER ASY, 4" BORE X 24.63" STROKE 1 02981929 1 BARREL WELDMENT 2 02981930 1 ROD WELDMENT 3 02982250 2 BUSHING, ROD END 1-1/2" LG 4 02982251 2 BUSHING, BARREL END 2" LG 5 02982068 1 SEAL KIT

Page 78

HYDRAULIC CYLINDER ASY - HEAD SWIVEL (OPTIONAL)

ITEM PART NO. QTY. DESCRIPTION

02961480A 1 DOOR CYLINDER ASY. 1 5JRC12160 1 LOCKNUT 2 33309 1 PISTON 3 02975865 1 ROD WLD’MT 4 02975866 1 TUBE / BARREL WLD’MT 5 02975867 1 CYLINDER HEAD 6 * SEAL KIT 1 ROD WIPER SEAL (IN ITEM 12) 7 * SEAL KIT 1 ROD SEAL (IN ITEM 12) 8 * SEAL KIT 1 O-RING (IN ITEM 12) 9 * SEAL KIT 1 SEAL (IN ITEM 12) 10 * SEAL KIT 1 PISTON SEAL (IN ITEM 12) 11 ------------ 2 O-RING F/ O-RING BOSS FITTING 12 02975528 1 SEAL KIT (ITEMS 6 THRU 10)

Page 79

HYDRAULIC CYLINDER ASY - TILT

ITEM PART NO. QTY. DESCRIPTION

02984944 1 CYLINDER, 3.5B X 1.75R X16S 1 02986266 1 BARREL WLD`MT 2 02986287 1 ROD WLD`MT 3 02982250 2 BUSHING ROD END 1-1/2" LG 4 02986288 1 SEAL KIT

Page 80

HYDRAULIC TANK SUB-ASY

Page 81

HYDRAULIC TANK SUB-ASY

Continued... ITEM PART NO. QTY. DESCRIPTION

02987800 1 SUB-ASY HYDRAULIC TANK 1 02981389 1 TANK, WELDMENT, HYDRAULIC 2 02981413 1 WELDMENT, COVER, CLEANOUT 3 02985828 1 FILTER, RETURN, VISUAL INDICATOR 4 02968166 1 STRAINER, SUCTION 1-1/4 WITH 3/4" OULET 5 02964345 1 STRAINER, SUCTION 2 WITH 1-1/4 OUTLET 6 00012101 12 LOCKWASHER, 3/8" PL 7 00002000 10 HHCS 3/8 NC 3/4 PL5 8 02981400 1 O-RING, CLEANOUT SEAL 9 02981412 1 SENSOR, TEMPERATURE 10 02968880 1 GAUGE, TEMP LEVEL INDICATOR 11 02987786 1 ADP, HYD ELBOW 12MP - 12MP 90 12 65108000 1 ADP, HYD ELBOW 20MP - 20MP 90 13 02963659 1 PLUG, MAGNETIC 1" NPT 14 02041800 1 ADP, HYD ELBOW 12MP - 12MJ 90 15 02825900 1 ADP, HYD 8MP - 8MJ 90 16 02823200 1 ADP, HYD 4MP - 4MJ ST 17 00753642 6 HHCS 3/8 NC 1-1/4 PL5 18 02958316 1 ADP, HYD 16MB - 12MJ ST 19 02981386 1 ASY, SHIELD FORMED 20 00015800 4 LOCKNUT TLM 3/8 NC PLC 21 00011100 4 FLATWASHER 3/8 STD 22 02982876 1 PLATE FILTER ADAPTER 23 02982877 1 PIPE PLUG 3" 24 02982871 1 DRIVER SIDE COVER WELDMENT 25 02963662 1 GASKET, FILTER ASY, FIBER 26 00011400 4 BOLT, HHCS 3/8 NC 1 PL5 27 03101646 4 LOCKWASHER 3/8

Page 82

HYDRAULIC TANK W/PUMP AND ELECT VALVE ASY

Page 83

HYDRAULIC TANK W/PUMP AND ELECT VALVE ASY

Continued... ITEM PART NO. QTY. DESCRIPTION

02987401 1 ASY, COMPLETE, TANK & VALVE 1 02985829 1 ASY, TANK, HYDRAULIC 2 02984219 1 ASY, VALVE & FITTINGS 3 02978986 1 PUMP, HYDROSTAT 4 02981369 1 PUMP, LS VARIABLE DISP 5 02043600 2 ADP, HYD ELBOW 16MB - 16MJ 45 6 02981435 1 ADP, HYD ELBOW 10MB - 10FJX 90 7 02968167 1 ADP, HYD 16MB - 8MJ ST 8 02822700 1 ADP, HYD ELBOW 16MB - 12MJ 90 9 03200587 1 ADP, HYD. 8MB PLUG 10 63042700 1 ADP, HYD ST 12MB - 8MJ 11 02968922 1 ASY, PRESSURE FILTER HEAD 12 02161400 1 ADP, HYD ELBOW 12MB - 8MJ 90 13 02968923 1 ELEMENT, PRESSURE 14 02981437 1 ADP, HYD ST 12MB - 10MJ 15 02892000 6 HHCS 1/2NC 1-1/2 LG PL8 16 00001300 4 LOCKWASHER 1/2 17 00759635 4 FLATWASHER, 1/2 HARDENED 18 02981468 1 BRACKET, SHIPPING 19 02981463 1 FLANGE, ADP 1-1/4 X 20MJIC 45 20 00749103 1 #20 SPLIT FLANGE KIT 21 00001800 4 LOCKNUT TLM 1/2 NC PLB 22 02090800 1 ADP, HYD ELBOW 12MB - 12MJ 90 23 00753642 4 HHCS 3/8 NC 1-1/4 PL5 24 00011100 4 FLATWASHER 3/8 STD 25 00015800 4 LOCKNUT TLM 3/8 NC PLC 26 02962181 3 ADP HYD STGHT 4MB-4MJ 27 02968896 1 PLASTIC TIE, ORANGE, 11LG 28 02968894 1 PLASTIC TIE, RED, 11LG 29 02982469 1 O-RING 4"ID X 1/16" 30 02970702 1 ADP HYD TEE 4MJ-4MJ-4FJX 31 02983892 1 PLATE, ADP, PVG32 32 10119000 4 HHCS 5/16 NC 1 PL5 33 00011700 4 LOCKWASHER 5/16 PL STD 34 00023500 4 FLATWASHER 5/16, TYPE AW, ZP

Page 84

JOYSTICK CONSOLE ASY

Page 85

JOYSTICK CONSOLE ASY

Continued... ITEM PART NO. QTY. DESCRIPTION

02987829 1 JOYSTICK ASSEMBLY W/ COMPONENTS 1 02981020 1 LED RED 12VDC 2 02981021 1 DECAL JOYSTICK OPERATION CNSLE 3 02981022 2 SWITCH MOMNTRY PUSHBUTTON RED 3A 02983472 2 PUSH BOTTOM CAP RED 4 02981023 2 SWITCH MOMNTRY PUSHBUTTON BLK 4A 02983473 2 BOTTON COVER BLACK 5 02981024 1 SOCKET RELAY 6 02981025 1 RELAY SPDT 12VDC 20A 7 02981026 1 CIRCUIT BREAKER 10A PANEL MNT 8 02981027 1 BOOT CIRCUIT BREAKER COVER 9 02977642 1 CONNECTOR RECEPTACLE 9A 02977645 17 PIN, 16-18 AWG 9B 02977646 4 PIN, 12AWG 10 02977643 1 NUT, PANEL - 24 SHELL SIZE 11 02981028 1 SWITCH PUSH PULL 12 02981029 1 JOYSTICK ASSEMBLY 13 02981031 1 HANDLE ASSEMBLY 14 02981032 1 DECAL SWITCH OPERATION HANDLE 15 02981033 1 ASSEMBLY PUSHBUTTON FACE PLATE 16 02981030 1 SWITCH MOMENTARY PUSHBUTTON 17 02977644 1 LOCKWASHER - 24 SHELL SIZE 18 02977043 1 SWITCH ROCKER DPDT W/GREEN LED 19 02983475 1 POTENTIOMETER - SWING 20 02983476 2 POTENTIOMETER - LIFT & DIPPER 21 02983477 8 MACHINE SCREW #10-32 5/8 LG. 22 02983478 8 WASHER #10 NYLON 23 02963584 1 LOCKNUT 8-32 PL

02987905 1 TRIGGER SWITCH

Page 86

PUMP ASY - SERVO CONTROLLED (PART 1)

Page 87

PUMP ASY - SERVO CONTROLLED (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

02969527A 1 PISTON PUMP ASY, SERVO CONTROLLED 2 02977418 1 JAM NUT 3 02977419 1 RETAINING RING 4 02977420 2 RETAINING RING 6 02977421 1 SEAL WASHER 7 02977422 8 BOLT 8 02977423 1 ROTATING ASY 9 02977424 1 SERVO PISTON SUB-ASY 10 02977425 1 FOLLOWER, SERVO PISTON 11 02977426 1 COVER PLATE 12 02977427 2 GASKET, F/ COVER PLATE 14 02977428 1 GASKET, F/ HOUSING 16 02970209 1 GASKET, F/ CONTROL HOUSING 17 02977430 1 COVER PLATE 18 02977431 1 CAM PLATE SUB-ASY 19 02977432 2 RACE, THRUST 20 02977433 1 BEARING, THRUST 21 02977434 2 RELIEF VALVE SUB-ASY 22 02977525 2 O-RING 23 02977434 1 RELIEF VALVE SUB-ASY 24 02977436 2 BOLT 25 02977437 2 BOLT 26 02970208 6 BOLT 27 02977439 1 PLATE, VALVE 28 02977440 1 HOUSING, SUB-ASY 29 02977526 1 HOUSING 30 02977527 1 BEARING 31 02977528 1 PLUG, SUB-ASY 32 02977529 1 O-RING 33 02977530 1 CRADLE, SUB-ASY 34 02977531 2 DOWEL BUSHING 35 02977532 1 BUSHING 36 02977533 1 BOLT, BUTTON HEAD 37 02977534 2 BOLT 38 02977535 2 SEAL SUB-ASY 39 02977441 1 BACK PLATE SUB-ASY 40 02977536 1 BEARING, PRESS FIT 41 02977537 1 ROLL PIN 42 02977325 1 SHAFT, SPLINED DRIVE 43 02977551 1 KIT, A-FLANGE COVER PLATE 44 02977442 1 O-RING

Page 88

PUMP ASY - SERVO CONTROLLED (PART 2)

Page 89

PUMP ASY - SERVO CONTROLLED (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

45 02977444 2 BOLT 46 02977449 1 PLATE, COVER 47 02977443 1 O-RING 48 02977445 1 WASHER 49 02977446 1 PLUG SUB-ASY 50 02977538 1 O-RING 51 02977540 1 PLUG 52 02977541 1 O-RING 53 02977447 2 PLUG 54 02977539 2 O-RING 57 02977448 1 KEY 58 02977199 1 SEAL, SHAFT 59 ----------- 1 CHARGE PUMP ADAPTER SUB-ASY 60 02977543 1 BUSHING, PRESS FIT, W/ 11 TOOTH SHAFT 61 02977544 1 PLUG 62 02977545 1 O-RING 63 02977546 1 SHIM 64 02977547 1 SPRING 65 02977548 1 POPPET 66 02970207 1 2 POSITION SERVO CONTROL SUB-ASY 67 02977451 1 GEROTOR, INNER RING 68 02977452 1 GEROTOR, OUTER RING 69 02977453 3 ORIFICE, CONTROL VALVE 72 02977456 1 COUPLER 73 02977457 2 RETAINING RING 74 02977458 1 PLUG SUB-ASY 75 02977459 1 WASHER 76 02977460 8 WASHER 77 02977461 4 WASHER 78 02977462 1 RING LOCK (NOT SHOWN) 79 02972835 1 CARTRIDGE VALVE ASY, W/O COIL - F/COILS W/RND METAL HSG (UNITS SHIPPED JUNE 2005 & UP)

02983257 1 CARTRIDGE VALVE ASY, W/O COIL - F/COILS W/SQ PLASTIC HSG (UNITS SHIPPED MAY 2005 & DOWN) 80 02972836 1 COIL ASY, COIL W/RND METAL HSG (UNITS SHIPPED JUNE 2005 & UP)

02983256 1 COIL ASY, COIL W/SQ PLASTIC HSG (UNITS SHIPPED MAY 2005 & DOWN)

- 02977086 1 SEAL KIT - PUMP

Page 90

PUMP-TANK-VALVE COVER

ITEM PART NO. QTY. DESCRIPTION

1 02981381 1 ASY, PUMP COVER

- 02981441 2 KNOB 3/8NC X 1-1/2 STUD

02986111 3.3 CABLE, PUMP COVER 36" LG

00001000 2 CABLE CLAMP

Page 91

THIS PAGE INTENTIONAL LEFT BLANK

Page 92

VALVE ASSEMBLY - ELECTRO-HYDRAULIC VALVE

Page 93

VALVE ASSEMBLY - ELECTRO-HYDRAULIC VALVE

Continued... ITEM PART NO. QTY. DESCRIPTION

- 02984219 1 ASY VALVE CCLS 5 SPOOL 1 02971378 1 VALVE, PVG32 2 02090800 2 ADP, HYD ELBOW 12MB - 12MJ 90 3 02972179 2 ADP, HYD ST 10MB - 4MJ 4 02976532 2 ADP, HYD, 4MJ-4FJX 45 5 02972177 3 ADP, HYD ST 10MB - 6MJ 6 02972113 5 ADP, HYD 10MB - 8FB 7 02975438 1 ADP, HYD STGHT 8FJX-8MB 8 00696800 1 ADP HYD STGHT 8MB-8MJ 90° 9 02969398 2 ORIFICE, .055 RESTRICTOR 10 02972209 1 ORIFICE, .063 RESTRICTOR 11 02972210 1 ORIFICE, .070 RESTRICTOR 12 02969399 1 ORIFICE, .040 RESTRICTOR 13 02968850 4 ADP, HYD ST 8MB-6MJ 14 02976531 7 ADP HYD ELBOW 6MJ-6FJX 45 15 02972178 1 ADP, HYD ELBOW 12MB - 8MJ 90 16 02972208A 1 ASY, VALVE SOLENOID 17 02822300 1 ADP, HYD ST 8MB-4MJ

Page 94

WIRE HARNESS ELECT-HYD VALVE

Page 95

WIRE HARNESS ELECT-HYD VALVE

Continued... ITEM PART NO. QTY. DESCRIPTION

1 02984735 1 ASY, HARNESS, MACHETE

Machete 2 HF (11-08)

Page 96

Page 97

ALAMO INDUSTRIAL

Limited Warranty

1. LIMITED WARRANTIES

1.01. Alamo Industrial warrants for one year from the purchase date to the original non-commercial, governmental, or

1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be

1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,

1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any

2. REMEDIES AND PROCEDURES.

2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer

2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the

2.03. Purchaser is responsible for returning the goods in question to the Dealer.

2.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and

2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and

3. LIMITATION OF LIABILITY.

3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES

3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR

3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO

3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER

4. MISCELLANEOUS.

4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,

4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall

4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the

4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship.

defective under normal use and service due to defects in material or workmanship.

negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator’s Manual.

nature on behalf of Manufacturer.

within 30 days of purchase.

goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based.

service due to defects in material or workmanship, Manufacturer will:

(a) Repair or replace the defective goods or part(s) or (b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer.

The choice of remedy shall belong to Manufacturer.

for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory.

WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

USE OF THE GOODS.

PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.

THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.

Texas.

be deemed to be a waiver of any other term.

invalidity of such provision shall not invalidate any other provisions herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty.

Alamo Industrial Implement Model ____________________________ Serial Number ________________________________ Date Purchased __________________________________________ Dealer ______________________________________

ATTENTION: READ YOUR OPERATOR’S MANUAL

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 830-379-1480

Page 98

TO THE OWNER/OPERATOR/DEALER

To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and

2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and

3. Ensure that each employee uses such Seatbelt while the tractor is moving; and

4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seatbelt if the tractor has a ROPS.

2. Where possible, avoid operating the tractor near ditches, embankments, and holes.

3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.

4. Stay off slopes too steep for safe operation.

5. Watch where you are going - especially at row ends, on roads, and around trees.

6. Do not permit others to ride.

7. Operate the tractor smoothly - no jerky turns, starts, or stops.

8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.

9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machinery guards in place...

Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.

Page 99

Machete 2 HF Pub 11-08 P/N 02986941P

Printed U.S.A

Alamo MACHETE2 02986941P User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual