Alamo 803213P User Manual

INTERSTATER

Flail Mower

Rev 06-11 Part No. 803213P

PART'S MANUAL

An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (800-356-6286) to obtain a Free copy before operating the equipment.

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 210-372-3551

TO THE OWNER/OPERATOR/DEALER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that

you retain. The use of "will-t" parts will void your warranty and can cause catastrophic failure with possible injury or death.

BOLT TORQUE

Mounting procedures for mowers will require a signicant amount of bolt nut and washer installation.

Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness.

Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart.

Bolt tightness should be completed with and checked with a suitable torque wrench.

Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual.

Loose bolts on a frame or in a casting may be a result of:

● Vibration from the mower due to imbalance of the mower blades

● Pulled threads due to over tightening

● Distortion of the hole due to under tightening during installation

Bolts broken or sheared in the mounting structure or tractor may be the result of:

● Improper alignment of the Mounting Plate or Structure such that it is not sitting at on the mating surface

● Distortion of the bolt due to over-tightening

● Under tightening of the bolts

Check the bolt torque during installation and prior to delivery with a suitable torque wrench.

PARTS

SECTION

Parts Section – 1

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and

are subject to special handling. Request a quotation for such parts before sending a Purchase

Order.

6. The Manufacturer reserves the right to change prices without prior notice.

Note: Please refer to The Safety Section in the front of this Manual for the proper part number

when ordering replacement safety decals.

For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 830-379-1480

Parts Section – 2

PART NAME INDEX

CHECK CHAINS - REAR MOWER............................................................................................................................................................ 5

CLUTCH ASY - P/N 00759985..................................................................................................................................................................... 6

CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 AND BELOW)............................................................................................................ 7

CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 TO CURRENT)........................................................................................................... 9

CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 AND BELOW).......................................................................................................... 11

CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 TO CURRENT)......................................................................................................... 13

CONTROL VALVE ASY - W/ STAND..................................................................................................................................................... 15

CUTTER KNIVES - CC - FC - RENV - PACKAGES & KITS................................................................................................................. 17

CUTTER KNIVES - CC - FC - RENV - SINGLE & BULK...................................................................................................................... 19

CYLINDER ASY - LIFT CYL - P/N 701104A........................................................................................................................................... 21

CYLINDER ASY - TILT CYL - P/N 701105A.......................................................................................................................................... 22

CYLINDER ATTACHMENT - LIFT & TILT............................................................................................................................................ 23

DECALS & LOCATION............................................................................................................................................................................. 25

DRIVELINE ASY - P/N 001863................................................................................................................................................................. 27

GEARBOX ASY - P/N 702673................................................................................................................................................................... 29

HYD SCHEMATIC - CYL HOSE - CONTROL DUAL WING................................................................................................................ 31

HYD SCHEMATIC W/ PARTS - DUAL WING........................................................................................................................................ 33

HYD SCHEMATIC W/ PARTS - RIGHT WING FIRST........................................................................................................................... 35

HYD SCHEMATIC W/ PARTS - RIGHT WING ONLY.......................................................................................................................... 37

HYD TANK ASY - PN 02981133............................................................................................................................................................... 39

MOTOR ASY - LEFT WING...................................................................................................................................................................... 41

MOTOR ASY - RIGHT WING................................................................................................................................................................... 42

MOTOR REPAIR PARTS - P/N 001602.................................................................................................................................................... 43

MOTOR REPAIR PARTS - P/N 02985522................................................................................................................................................ 45

MOWER ASY - LH & RH WING 50 (PART 1)......................................................................................................................................... 47

MOWER ASY - LH & RH WING 50 (PART 2)......................................................................................................................................... 49

MOWER ASY - LH & RH WING 50 (PART 3)......................................................................................................................................... 51

MOWER ASY - LH & RH WING 62 (PART 1)......................................................................................................................................... 53

MOWER ASY - LH & RH WING 62 (PART 2)......................................................................................................................................... 55

MOWER ASY - LH & RH WING 62 (PART 3)......................................................................................................................................... 57

MOWER ASY - LH & RH WING 74 (PART 1)......................................................................................................................................... 59

MOWER ASY - LH & RH WING 74 (PART 2)......................................................................................................................................... 61

MOWER ASY - LH & RH WING 74 (PART 3)......................................................................................................................................... 63

MOWER ASY - LH & RH WING 88 (PART 1)......................................................................................................................................... 65

MOWER ASY - LH & RH WING 88 (PART 2)......................................................................................................................................... 67

MOWER ASY - LH & RH WING 88 (PART 3)......................................................................................................................................... 69

MOWER ASY - REAR 88 (PART 1).......................................................................................................................................................... 71

MOWER ASY - REAR 88 (PART 2).......................................................................................................................................................... 73

MOWER ASY - REAR 88 (PART 3).......................................................................................................................................................... 75

MOWER ASY - REAR 88 (PART 4).......................................................................................................................................................... 77

PART NAME INDEX

MOWER ASY - REAR 96 (PART 1).......................................................................................................................................................... 79

MOWER ASY - REAR 96 (PART 2).......................................................................................................................................................... 81

MOWER ASY - REAR 96 (PART 3).......................................................................................................................................................... 83

MOWER ASY - REAR 96 (PART 4).......................................................................................................................................................... 85

OPTIONAL CASTER WHEELS - REAR MOWER LAMINATED......................................................................................................... 87

OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 1)......................................................................................... 88

OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 2)......................................................................................... 89

OPTIONAL EQUIPMENT - ACCESSORIES - PACKAGES.................................................................................................................... 90

PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 1)...................................................................................................... 91

PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 2)...................................................................................................... 93

PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 1).................................................................................................... 95

PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 2).................................................................................................... 97

PUMP ASY - SINGLE PUMP - SINGLE WING....................................................................................................................................... 99

PUMP ASY - TANDEM FRONT PUMP - DUAL WINGS..................................................................................................................... 101

PUMP ASY - TANDEM REAR PUMP - DUAL WINGS........................................................................................................................ 103

PUMP ASY, GEAR TYPE - FRONT P/N 000889 - HYD CYL SUPPLY............................................................................................... 105

TUBING ASY HYD - DUAL WING ASY P/N 02963561....................................................................................................................... 106

TUBING ASY HYD - SINGLE WING - ASY P/N 02963562................................................................................................................. 107

VALVE REMOTE CONTROL................................................................................................................................................................. 109

WIRE HARNESS - DUAL WINGS.......................................................................................................................................................... 111

WIRE HARNESS - RH WING - FIRST OR ONLY................................................................................................................................. 112

CHECK CHAINS - REAR MOWER

ITEM PART NO. QTY. DESCRIPTION

702264 1 CHECK CHAIN KIT ASY 1 103333 2 CHAIN - 9 LINKS 2 000413 4 BOLT 3 000414 4 NUT 4 101780 4 WASHER 5 104736 2 LIFT CHAIN CLEVIS - UPPER 6 104926 2 LIFT CHAIN CLEVIS - LOWER

CLUTCH ASY - P/N 00759985

ITEM PART NO. QTY. DESCRIPTION

00759985 1 CLUTCH ASY, 4-DISK 1 00754302 1 YOKE, FLANGED 2 00755599 1 BODY, FRICTION CLUTCH 3 00754203 1 PRESSURE PLATE 5 00754202 4 RING,CLUTCH LINING 6 00754301 1 BUSHING 7 00754303 8 SPRING CLUTCH 8 00755600 2 NUT & BOLT 14MM X 70MM 9 00754199 8 BOLT & NUT M10 X 95 MM SELF LK NUT 10 00754201 1 INNER PLATE

CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 AND BELOW)

Continued... ITEM PART NO. QTY. DESCRIPTION

702743 1 VALVE ASY, 2-SPOOL COMPLETE 1 001415 2 HANDLE KIT ASY 2 001416 1 CHECK VALVE KIT ASY 3 001417 1 SPOOL POSITION KIT (TILT SECTION) 4 001418 1 DUST COVER (TILT SECTION) 5 001419 1 TILT SECTION, COMPLETE (INC. 1-3) 6 001420 2 BODY SEAL KIT 7 001421 1 SPOOL POSITION KIT (LIFT SECTION) 8 001422 1 DUST COVER (LIFT SECTION) 9 001423 1 LIFT SECTION, COMPLETE (INC. 1,2,7) 10 001424 1 OUTLET SECTION 11 001425 1 RELIEF VALVE KIT 12 001426 1 INLET SECTION SEAL KIT 13 001427 1 INLET SECTION, W/RELIEF VALVE #11 14 001428 2 MOUNTING BRACKET 15 001429 1 TIE ROD KIT (2 SECTION VALVE) 16 001288 2 SWIVEL HOSE ADAPTER W/ O-RING 17 000755 2 SWIVEL UNION, 1/4 MALE X 1/4 FEMALE 90` 18 03200284 2 STRAIGHT ADAPTER 19 002487 2 KNOB 20 002488 2 BRACKET 21 02972112 1 STRAIGHT ADAPTER 22 02822300 1 STRAIGHT ADAPTER 23 02969398 1 ORIFICE PLATE

CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 TO CURRENT)

ITEM PART NO. QTY. DESCRIPTION

02989810 1 VALVE 2-SPOOL W/BRKTS 1 001415 2 KIT, HANDLE ASSY 2 001416 1 KIT, CHECK VALVE ASSY 3 001417 2 KIT SPOOL POSITION 4 001418 2 DUST COVER (TILT SECTION) 5 001419 2 SECTION TILT COMPLETE 6 001420 2 KIT, BODY SEAL 7 001424 1 SECTION, OUTLET 8 001425 1 KIT, RELIEF VALVE 9 001426 1 KIT, INLET SECTION SEAL 10 001427 1 SECTION, INLET W/RELIEF VALVE 11 001428 2 BRACKET MOUNTING 12 ---------- 1 KIT TIE ROD 13 002487 2 KNOB, CONTROL VALVE 14 002488 2 BRACKET, CONTROL 15 02978229 2 BRACKET, CONTROL 16 02979134 2 SPOOL WIPER 17 02988821 2 O-RING, SPOOL SEAL 18 02988822 2 BUSHING, SPOOL SEAL 19 02822300 4 ADP HYD STGHT 6MB-4MJ 20 02969398 4 ORIFICE, 0.055 ONE-WAY RSTCR 21 02972112 4 ADP HYD STGHT 6MB-4MJ

THIS PAGE INTENTIONAL LEFT BLANK

CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 AND BELOW)

Continued... ITEM PART NO. QTY. DESCRIPTION

702744 1 VALVE ASY, 4-SPOOL COMPLETE 1 001415 4 HANDLE KIT ASY 2 001416 1 CHECK VALVE KIT ASY 3 001417 2 SPOOL POSITION KIT (TILT SECTION) 4 001418 2 DUST COVER (TILT SECTION) 5 001419 2 TILT SECTION, COMPLETE (INC. 1-3) 6 001420 4 BODY SEAL KIT 7 001421 2 SPOOL POSITION KIT (LIFT SECTION) 8 001422 2 DUST COVER (LIFT SECTION) 9 001423 2 LIFT SECTION, COMPLETE (INC. 1,2,7) 10 001424 1 OUTLET SECTION 11 001425 1 RELIEF VALVE KIT 12 001426 1 INLET SECTION SEAL KIT 13 001427 1 INLET SECTION, W/RELIEF VALVE #11 14 001428 2 MOUNTING BRACKET 15 001430 1 TIE ROD KIT (4 SECTION VALVE) 16 001288 2 SWIVEL HOSE ADAPTER W/ O-RING 17 000755 2 SWIVEL UNION, 1/4 MALE X 1/4 FEMALE 90` 18 03200284 4 STRAIGHT ADAPTER 19 002487 4 KNOB 20 002488 4 BRACKET 21 02972112 2 STRAIGHT ADAPTER 22 02822300 2 STRAIGHT ADAPTER 23 02969398 2 ORIFICE PLATE

CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 TO CURRENT)

ITEM PART NO. QTY. DESCRIPTION

02989811 1 VALVE 4-SPOOL W/BRKTS 1 001415 4 KIT,HANDLE ASSY 2 001416 1 KIT,CHECK VALVE ASSY 3 001417 4 KIT SPOOL POSITION 4 001418 4 DUST COVER (TILT SECTION) 5 001419 4 SECTION TILT COMPLETE 6 001420 4 KIT, BODY SEAL 7 001424 1 SECTION, OUTLET 8 001425 1 KIT, RELIEF VALVE 9 001426 1 KIT, INLET SECTION SEAL 10 001427 1 SECTION, INLET W/RELIEF VALVE 11 001428 2 BRACKET MOUNTING 12 001430 1 KIT TIE ROD 13 002487 4 KNOB,CONTROL VALVE 14 002488 2 BRACKET,CONTROL VALVE 15 02978229 2 BRACKET,CONTROL VALVE 16 02979134 4 SPOOL WIPER 17 02988821 2 O-RING, SPOOL SEAL 18 02988822 2 BUSHING, SPOOL SEAL 19 02822300 4 ADP HYD STGHT 6MB-4MJ 20 02969398 4 ORIFICE, 0.055 ONE-WAY RSTCR 21 02972112 4 ADP HYD STGHT 6MB-4MJ

THIS PAGE INTENTIONAL LEFT BLANK

CONTROL VALVE ASY - W/ STAND

Continued... ITEM PART NO. QTY. DESCRIPTION

1 702782 1 VALVE MOUNTING BRACKET 2 106597 1 COVER TOP 3 702744 1 VALVE ASY, 4-SPOOL (W/ FITTINGS

02989811 1 VALVE ASY, 4-SPOOL (W/O FITTINGS)

702743 1 VALVE ASY, 2-SPOOL (W/ FITTINGS)

02989810 1 VALVE ASY, 2-SPOOL (W/O FITTINGS) 5 00753642 2 BOLT 6 00015800 12 LOCKNUT 7 002498 1 WIRE HARNESS - DUAL WING W/ ROPS

002499 1 WIRE HARNESS - RIGHT WING FIRST W/ ROPS

002500 1 WIRE HARNESS - DUAL WING W/CAB

002501 1 WIRE HARNESS - RIGHT WING FIRST W/CAB 8 000141 3 CAPSCREW 9 00001800 3 LOCKNUT 10 106534 1 VALVE STAND - STRAIGHT

106755 1 VALVE STAND - ANGLED IN

106842 1 VALVE STAND - ANGLED OUT 11 001774 1 HOSE 12 001773 1 HOSE 13 001772 1 HOSE 14 001771 1 HOSE 15 001700 2 HOSE 16 702783 1 COVER W/ DECAL 17 00011400 10 CAPSCREW 18 00011100 8 WASHER 19 ----------- 1 HOSE 21 02964028 1 ON/OFF SWITCH 22 02964063 1 ON/OFF KNOB

CUTTER KNIVES - CC - FC - RENV - PACKAGES & KITS

Continued... ITEM PART NO. QTY. DESCRIPTION

1 02986836 1 KNIFE PKG FC STD, PIN MNT` D KN #02988196 2 02986337 1 KNIFE PKG CC STD, RING MNT` KN #02986332 3 702254 1 KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # 02986276 4 702254A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT KN #108381 5 02986837 1 KNIFE PKG FC STD, PIN MNT`D KN #02988196 6 02986838 1 KNIFE PKG FC STD, PIN MNT`D KN #02988196 7 02986342 1 KNIFE PKG FC RCK & TRSH, RING MNT`D KN #02986333 8 02986335 1 KNIFE PKG CC STD, RING MNT`D KN #02986332 9 02986277 1 KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # 02986276 10 702255A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT`D KN #108381 11 02986839 1 KNIFE PKG FC STD, PIN MNT`D KN #02988196 12 02986343 1 KNIFE PKG FC RCK & TRSH, RING MNT`D KN #02986333 13 02986334 1 KNIFE PKG CC STD, RING MNT`D KN #02986332 14 02986278 1 KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # 02986276 15 702256A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT`D KN #108381 16 02986841 1 KNIFE PKG FC STD, PIN MNT`D KN #02988196 17 02986341 1 KNIFE PKG FC RCK & TRSH, RING MNT`D KN #02986333 18 100761 50 RING ORDER W/ PKG #02986339 19 703873 1 RING PIN & COTTER PIN BAG (50 PCS) ORDER W/PKG #02986339 20 02986281 1 KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # 02986276 21 703874A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT`D KN #108381 22 02986840 1 KNIFE PKG FC 250 PCS 23 02986842 1 KNIFE PKG FC 500 PCS

CUTTER KNIVES - CC - FC - RENV - SINGLE & BULK

Continued... ITEM PART NO. QTY. DESCRIPTION

1 02988196 1 KNIFE, FC PIN MNTD (STD)

02986843 - BULK PKG, 2500 PCS FC KNIFE

02986844 - BULK PKG, 5000 PCS FC KNIFE 2 101034 1 KNIFE PIN, HEAT TREATED 4 02986333 1 KNIFE, FC RING & CLIP MNTD

02986334 - BULK PKG, 500 PCS FC KNIFE

02986347 - BULK PKG, 2500 PCS FCKNIFE 5 101991 1 KNIFE RING (USE W/ 02986333KNIFE) 6 000210 1 LOCKNUT, 5/16"-NF PLB (USE W/ KNIFE 02986333) 7 02990020 1 RING CLIP (USE W/ KNIFE 02986333) 8 000032 1 BOLT, HEX HEAD 5/16"-NF X 7/8" PL GR5 (USE W/ KNIFE 02986333) 9 02986332 1 KNIFE, CC RING MNTD

02986340 - BULK PKG 2500 PCS CC KNIFE

02986338 - BULK PKG 5000 PCS CC KNIFE

02986276 1 KNIFE, CC ES HD (SHEARED EDGE)

02986277 - BULK PKG, 2000 PCS CC ES HD KNIFE

02986280 - BULK PKG, 4000 PCS 02986276 CC ES HD KNIFE

108381 1 KNIFE, CC ES HD (FORGED EDGE)

702658A - BULK PKG, 2000 PCS CC ES HD 108381 KNIFE

703865A - BULK PKG, 3500 PCS CC ES HD 108831 KNIFE 10 100761 1 KNIFE RING (USE W/ KNIFE 02986332, 02986276 OR 108381) 11 102670 1 PIN, HARDENED (USE W/ KNIFE 02986332, 02986276 OR 108381) 12 02668700 1 COTTER PIN (USE W/ KNIFE 02986332, 02986276 OR 108381)

CYLINDER ASY - LIFT CYL - P/N 701104A

ITEM PART NO. QTY. DESCRIPTION

701104A 1 LIFT CYL ASY (W/0 FITTINGS) 1 002615 1 CYLINDER ROD 2 002614 1 CYLINDER BARREL 3 002613 1 CYLINDER HEAD 4 002616 1 PISTON 5 5JRC16140 1 NUT 11 * 1 SEAL PISTON 12 001007 2 COTTER PIN 13 700992 1 ROD END CLAMP W/ SET SCREW 14 700907 1 ROD END W/ GREASE FITTING 15 00755153 2 COTTER PIN 16 001750 2 PIN 17 02960018 2 ELBOW 18 02960054 1 PLUG 19 103139A 1 CYLINDER (W/O ITEMS 13 & 14) 20 000872 1 SEAL KIT, (ITEMS 6, 7, 8, 9, 10 & 11)

CYLINDER ASY - TILT CYL - P/N 701105A

ITEM PART NO. QTY. DESCRIPTION

1 701105A 2 TILT CYL W/0 FITTINGS MA 2 002624 1 CYLINDER ROD 3 002622 1 CYLINDER HEAD 4 002625 1 PISTON 5 5JRC16140 1 NUT 11 * 1 SEAL PISTON 12 001007 2 COTTER PIN 13 700992 1 ROD END CLAMP W/ SET SCREW 14 700907 1 ROD END W/ GREASE FITTING 15 00755153 2 COTTER PIN 16 001750 2 PIN 19 103140A 1 CYLINDER 20 000873 1 SEAL KIT

CYLINDER ATTACHMENT - LIFT & TILT

Continued... ITEM PART NO. QTY. DESCRIPTION

1 700883 4 INNER PIVOT PIN W/GREASE FITTING 2 02035400 4 BOLT 3 03101646 4 LOCKWASHER 4 001007 2 PIN W/CLIP 5 700992 4 ROD END CLAMP 6 700907 4 ROD END W/GREASE FITTING 7 02960054 2 PLUG 8 104039 4 BUSHING 9 702706 4 PIVOT W/BUSHING 10 103538 4 BUSHING 11 000941 4 GREASE FITTING 12 000088 2 GREASE FITTING 13 103266 4 CYLINDER PIN 14 00755153 8 COTTER PIN 15 ----------- 1 RIGHT HAND LIFT FRAME (CALL CUSTOMER SERVICE FOR DETAILS)

----------- 1 LEFT HAND LIFT FRAME (CALL CUSTOMER SERVICE FOR DETAILS) 16 103062 2 PIVOT PIN 17 000760 4 NUT

* 1 LIFT STAND - RIGHT HAND (NOT SHOWN) 19 02960018 6 ELBOW, 90 DEG. 20 00750952 12 BOLT 21 00695100 16 NUT 22 00750311 2 BOLT 23 02963584 2 LOCKNUT 24 02963585 2 MACHINE SCREW 25 107222 1 MOUNTING SWITCH 26 703520 1 SWITCH 27 002019 1 MAGNET 28 002020 1 SPACER 29 107225 1 MOUNTING LH

107224 1 MOUNTING RH 30 103139A 2 LIFT CYLINDER W/PIN & CLIP 31 103140A 2 TILT CYLINDER W/PIN & CLIP 32 107242 4 SPACER 33 00027100 2 BOLT 34 00011700 2 LOCKWASHER 35 107621 2 PIVOT PIN 36 002496 1 WIRE HARNESS RIGHT WING

002497 1 WIRE HARNESS LEFT WING

DECALS & LOCATION

Continued... ITEM PART NO. QTY. DESCRIPTION

1 002369 4 DECAL, MULTI HAZARD 2 002425 3 DECAL, FRONT SHIELD REMOVAL 3 00753840 2 DECAL, SAFETY, WING LOWERING 4 00756004 2 DECAL, SHIELD MISSING 5 00756005 2 DECAL, ROTATING DRIVELINE 6 00756007 3 DECAL, WARNING CHAINGUARD 7 00756059 3 DECAL, WARNING OIL LEAK 8 00756485 2 DECAL, ROTATING BLADES 9 00756494 1 DECAL, DANGER DRIVELINE 10 00758194 3 DECAL, WARNING BELT SHIELD 11 02962765 2 DECAL, MULTIPLE HAZARD 12 03200285 2 DECAL, WATCH YOUR STEP 13 03100328 1 WLDMT, ROTOR SHAFT 14 02971123 1 DECAL, WARNING PRESSURIZED TANK 15 03200347 - EMBLEM, SMV (FURNISHED W/ TRACTOR OR DEALER) 16 1458392 4 DECAL, RED REFLECTOR 17 1458393 4 DECAL, YELLOW REFLECTOR 18 02966305 1 DECAL, UNIVERSAL TRACTOR 19 03200432 3 DECAL, FLAIL PARTS INFO 20 002023 3 DECAL, HEIGHT ADJ 21 001412 1 DECAL, CONTROL VALVE 22 000108 3 DECAL, OPERATING INSTRUCTIONS 23 000678 2 DECAL, GREASE FITTING INSIDE 24 001829 2 DECAL, LUBRICATION WINGS 25 001830 1 DECAL, LUBRICATION REAR 26 02962748 2 DECAL, ON-OFF SWITCH CUTTER VLV 27 02965093 1 DECAL, PROPER ENGINE OPERATING 28 00763977 1 DECAL, NOTICE TO OWNER 29 001650 1 DECAL, ALAMO IND. LOGO 30 001651 4 DECAL, ALAMO IND BLK & GRN 31 02960766 3 DECAL, ALAMO INDUSTRIAL LOGO 32 001660 2 DECAL, INTERSTATER 34 NFS - SERIAL NUMBER PLATE , REAR MOWER (1) 35 02977385 1 PARTS MANUAL HOLDER CANISTER 36 02977417 1 DECAL, OPERATORS MANUAL INSIDE 37 803213C 1 MANUAL. OPERATORS INTERSTATER 38 10058000 4 BOLT, HEX HEAD 1/4"-NC X 1" PL GR5 39 00017000 4 LOCKWASHER, 1/4" PL STD 40 00024100 4 FLATWASHER, 1/4" STD

DRIVELINE ASY - P/N 001863

Continued... ITEM PART NO. QTY. DESCRIPTION

001863 1 DRIVELINE ASY W/CLUTCH & SHIELDS 1 00759948 1 CLUTCH ASY 2 00759517 2 GREASE FITTING 3 00752896 2 UNIVERSAL JOINT 4 00754154 1 OUTER TUBE YOKE 6 00760242 1 OUTER TUBE 7 00760243 1 INNER TUBE 8 00754153 1 INNER TUBE YOKE 9 00754167 1 ROLL PIN 10 00752883 1 YOKE, 1-3/8" - 6 11 00754335 1 GREASE FITTING 12 00756004 1 DRIVELINE WARNING LABEL 13 00760244 1 OUTER HALF W/SLIP CLUTCH 14 00760245 1 INNER HALF SHAFT W/1-3/8 - 6 YOKE 15 00763196 1 INNER SHIELD BEARING (NEW STYLE) 16 00759216 1 INNER SHIELD BEARING (USE WITH SET SCREW) 17 00759217 2 SCREW 18 00760250A 1 COMPLETE SHIELD 19 00756005 1 DRIVELINE SHIELD WARNING LABEL 20 00763195 1 OUTER SHIELD BEARING (NEW STYLE) 21 00759218 1 OUTER SHIELD BEARING (USE WITH SCREW) 22 00757144 1 Q.D. COLLAR KIT 23 00760248A 1 HALF INNER SHIELD 24 00760249A 1 HALF OUTER SHIELD

GEARBOX ASY - P/N 702673

Continued... ITEM PART NO. QTY. DESCRIPTION

702673 1 GEARBOX ASY 1 001718 1 PINION 2 001719 1 SEAL 3 001717 1 NUT 4 001720 1 SPRING WASHER 5 00754757 2 BEARING, ROLLER 6 001716 1 SPACER 7 00754752 2 CIRCLIP, INTERNAL 8 001722 1 BEARING, ROLLER 9 00753222 2 SHIM 10 00754761 1 SHIM 11 001724 1 SEAL 12 001725 1 SHAFT W/ CROWN WHEEL 13 00754459 1 BEARING, BALL 14 001708 8 BOLT 15 001710 1 COVER 16 00755633 2 PLUG 17 000055 2 PLUG, DRAIN 18 002516 1 HOUSING 19 00769800 1 GASKET

HYD SCHEMATIC - CYL HOSE - CONTROL DUAL WING

ITEM PART NO. QTY. DESCRIPTION

1 001775 1 HOSE, CONTROL VALVE TO PUMP 2 001776 1 HOSE, CONTROL VALVE TO RETURN FILTER 3 001773 1 HOSE, CONTROL VALVE TO TILT CYL. - LIVE END 4 001774 1 HOSE, CONTROL VALVE TO TILT CYL. - DEAD END 5 001772 1 HOSE, CONTROL VALVE TO LIFT CYL. - LIVE END 6 001771 1 HOSE, CONTROL VALVE TO LIFT CYL. - LIVE END 8 001770 1 HOSE, CONTROL VALVE TO TILT CYL. - LIVE END

THIS PAGE INTENTIONAL LEFT BLANK

HYD SCHEMATIC W/ PARTS - DUAL WING

Continued... ITEM PART NO. QTY. DESCRIPTION

1 001783 2 SUCTION HOSE 2 001788 2 HOSE, CASE DRAIN - PUMP 4 001579 2 HOSE, CASE DRAIN - MOTOR 6 002628 3 HOSE, MOTOR RETURN TO WING COOLING TUBE 8 001780 1 HOSE, MOTOR RETURN TO WING COOLING TUBE 11 001782 1 HOSE, SUCTION, GEAR PUMP 13 002332 2 HOSE, HYD PLUMBING TO MOTOR-PRESSURE-33" LONG

002365 2 HOSE, HYD PLUMBING TO MOTOR-PRESSURE- 62.5" LONG 14 02963432 2 HOSE, WING TO HYD PLUMBING-RETURN-33" LONG

002364 2 HOSE, WING TO HYD PLUMBING-RETURN -65.5" LONG 15 02963546 1 TUBE, MOTOR PRESSURE 16 02963547 1 TUBE, MOTOR RETURN 17 02963563 1 MOUNTING PLATE 18 02742500 1 ADAPTER HYD, 90 DEG BULKHEAD 19 00751846 1 ADAPTER HYD, STRAIGHT BULKHEAD 20 00749941 1 WASHER 21 002329 1 ADAPTER HYD, SPECIAL 22 02959283 1 TUBE CLAMP 23 107260 2 SLEEVING (SHORT) 27" LONG

106903 2 SLEEVING (LONG) 57" LONG 25 * 1 SLEEVING 26 02958858 1 ELBOW 90 DEG 28 02956851 2 ADAPTER HYD, 90 DEG. 29 108470 1 HOSE GUARD 30 108471 1 SIDE PLATE, HOSE GUARD 31 00011400 5 BOLT 32 00015800 5 LOCKNUT 33 0223200 2 FLATWASHER 34 02030700 1 BOLT 35 00001800 1 LOCKNUT

HYD SCHEMATIC W/ PARTS - RIGHT WING FIRST

Continued... ITEM PART NO. QTY. DESCRIPTION

1 001783 1 HOSE, SUCTION 2 001859 1 HOSE, CASE DRAIN - PUMP 3 001782 1 HOSE, SUCTION - GEAR PUMP 6 63078500 1 CAP, PIPE 9 002332 1 HOSE, HYD PLUMBING TO MOTOR-PRESSURE-33" LONG

002365 1 HOSE, HYD PLUMBLING TO MOTOR-PRESSURE- 62.5" LONG 10 02963432 1 HOSE, WING TO HYD PLUMBING-RETURN-33" LONG

002364 1 HOSE, WING TO HYD PLUMBING-RETURN 65.5" LONG 12 001579 1 HOSE, CASE DRAIN - MOTOR 13 00751003 1 PIPE PLUG 14 002628 2 HOSE, MOTOR RETURN TO WING COLOLING TUBE 15 107260 1 SLEEVING (SHORT) 27" LONG

106903 1 SLEEVING (LONG) 57" LONG 16 * 1 SLEEVING 18 02959154 1 ADAPTER HYD, ELBOW, 45 DEG. 19 02958858 1 ADAPTER HYD, ELBOW, 90 DEG. 20 02043600 1 ADAPTER HYD, ELBOW, 45 DEG. 21 001573 1 ADAPTER, STRAIGHT 22 02961098 1 ADAPTER HYD, ELBOW 90 DEG. BOSS 23 02963546 1 TUBE, MOTOR PRESSURE 24 02959283 1 TUBE CLAMP 25 002329 1 ADAPTER HYD - SPECIAL 26 00751846 1 ADAPTER HYD - STRAIGHT BULKHEAD 27 00749941 1 WASHER 28 02956851 1 ADAPTER HYD, 90 DEG. 31 02963563 1 WELDMENT - TUBE MNTG BRCKT 32 108470 1 HOSE GUARD 33 108471 1 SIDE PLATE, HOSE GUARD 34 00011400 5 BOLT 35 00015800 5 LOCKNUT 36 0223200 2 FLATWASHER 37 02030700 1 BOLT 38 00001800 1 LOCKNUT

HYD SCHEMATIC W/ PARTS - RIGHT WING ONLY

Continued... ITEM PART NO. QTY. DESCRIPTION

1 001783 1 HOSE, SUCTION 2 001859 1 HOSE, CASE DRAIN - PUMP 3 001782 1 HOSE, SUCTION - GEAR PUMP 6 63078500 1 CAP, PIPE 8 * 1 HOSE, HYD PLUMBING TO TANK - RETURN 9 002332 1 HOSE, HYD PLUMBING TO MOTOR-PRESSURE, 33" LG

002365 1 HOSE, HYD PLUMBING TO MOTOR-PRESSURE, 62.5" LG 10 02963432 1 HOSE, WING TO HYD PLUMBING-RETURN, 33" LG

002364 1 HOSE, WING TO HYD PLUMBING RETURN, 65.5" LG 12 001579 1 HOSE, CASE DRAIN - MOTOR 13 00751003 1 PIPE PLUG 14 002628 2 HOSE, MOTOR RETURN TO WING COOLING TUBE & CROSSOVER TUBE 15 107260 1 SLEEVING (SHORT) 27" LONG

106903 1 SLEEVING (LONG) 57" LONG 16 *Â¤ 1 SLEEVING 18 02959154 1 ADAPTER HYD, ELBOW, 45 DEG. 19 02958858 1 ADAPTER HYD, ELBOW, 90 DEG. 20 02043600 1 ADAPTER HYD, ELBOW, 45 DEG. 21 03200283 1 ADAPTER HYD, STRAIGHT 22 02961098 1 ADAPTER HYD, ELBOW, 90 DEG. BOSS 23 02956851 1 ADAPTER HYD, 90 DEG. 25 02919400 1 ADAPTER HYD, ELBOW BULKHEAD 26 00751846 1 ADAPTER HYD, STRAIGHT BULKHEAD 27 107245 1 CLAMP BRACKET 28 107404 1 MOUNTING PLATE 29 108470 1 HOSE GUARD 30 108471 1 SIDE PLATE, HOSE GUARD 31 00011400 5 BOLT 32 00015800 5 LOCKNUT 33 0223200 2 FLATWASHER 34 02030700 1 BOLT 35 00001800 1 LOCKNUT

HYD TANK ASY - PN 02981133

Continued... ITEM PART NO. QTY. DESCRIPTION

02981133 1 HYD TANK ASY, W/ FILTER 1 02981119 1 TANK WELDMENT 2 02967127 1 O-RING 3 02962617 1 FILTER ASY, W/ SHORT EXT TUBE 4 02049500 4 LOCKWASHER, 3/8" HIGHCOLLAR 5 000645 4 BOLT, HEX HEAD 3/8"-NC X 7/8" PL GR5 6 02968880 1 GAUGE, SIGHT & TEMPERATURE 7 02968879 1 FILLER CAP & BREATHER ASY 8 00751984 6 STARWASHER #10, EXT TOOTH PL 9 02969917 6 MACHINE SCREW, M5-P0.8 X 12MM 10 000695 2 PLUG, PIPE,SOCKET HEAD 1/4"-18 11 00752307 1 PLUG, MAGNETIC 1/2" NPT 12 001819 2 PLUG, CAP-TEAR TAB 1-1/4" 13 02979616 1 PIPE, CAP 3/4"-14 NPT

MOTOR ASY - LEFT WING

ITEM PART NO. QTY. DESCRIPTION

1 02964792 1 MANIFOLD 2 001759 1 RELIEF 3 02989700 1 SOLENOID VALVE - COMPLETE

02989699 1 SOLENOID VALVE CARTRIDGE

02989698 1 SOLENOID COIL 4 * 1 HOSE, PRESSURE 5 02090900 2 ELBOW 6 001574 1 CAP NUT 7 03200283 1 STRAIGHT ADAPTER 8 02964793 2 O-RING (NOT SHOWN) 9 63149100 1 ELBOW 10 00011700 4 LOCKWASHER 11 7AH551832 4 BOLT 12 001579 1 HOSE-DRAIN 13 001780 1 HOSE RETURN CROSSOVER 14 001654 1 ELBOW ADAPTER 15 02956851 1 ADAPTER 16 02985522 1 MOTOR 17 03200587 1 PLUG (NOT SHOWN) 18 002497 1 WIRE HARNESS LEFT WING

MOTOR ASY - RIGHT WING

ITEM PART NO. QTY. DESCRIPTION

1 02964792 1 MANIFOLD 2 001759 1 RELIEF 3 02989700 1 SOLENOID VALVE - COMPLETE

02989699 1 SOLENOID VALVE CARTRIDGE

02989698 1 SOLENOID COIL 4 * 1 HOSE, PRESSURE 5 02090900 1 ELBOW 6 7AH551832 1 ADAPTER 7 02985522 1 MOTOR 8 02964793 2 O-RING (NOT SHOWN) 9 63149100 1 ELBOW 10 00011700 4 LOCKWASHER 11 7AH551832 4 BOLT 12 001579 1 HOSE-DRAIN 13 002017 1 HOSE RETURN CROSSOVER 15 02958858 1 FORMED TUBE 16 001654 1 ELBOW ADAPTER 17 03200283 1 ADAPTER 18 001574 1 CAP 19 02956851 1 ADAPTER 20 03200587 1 PLUG (NOT SHOWN) 21 002496 1 WIRE HARNESS RIGHT WING

MOTOR REPAIR PARTS - P/N 001602

Continued... ITEM PART NO. QTY. DESCRIPTION

001602 1 MOTOR W/KEY 2.48 CU/IN. 1 001641 1 ROTATING KIT ASY 2 001642 1 PLATE ASY, BACKING 3 001643 1 SHAFT, KEYED 4 NFS 1 HOUSING ASY, (NOT FURNISHED AS PARTS) 5 001644 1 BEARING & RACE SET 6 001645 1 PLATE, CAM INSERT 7 03200409 1 O-RING 8 00016200 2 HHCS 5/16NC 2 PL5 9 03200411 1 WASHER 10 02966925 1 RING, SPIRAL 11 02977420 2 RETAINING RING 12 02966926 1 KIT, SEAL ADAPTER 12A 02966924 1 O-RING, 2.0 X 1-13/16 12B 02966922 1 SEAL, HIGH PRESSURE 12C 02966923 1 SEAL ADAPTER, 2.00 BORE 13 03200521 1 STEP KEY, 1/4 X 5/16 14 03200587 1 PLUG, HEX HD # 8MB 15 002339 1 BEARING, BACKPLATE 16 002340 1 BEARING HOUSING

001648 1 SEAL KIT

MOTOR REPAIR PARTS - P/N 02985522

Continued... ITEM PART NO. QTY. DESCRIPTION

02985522 1 MOTOR W/KEY 2.48 CU/IN. 1 001641 1 ROTATING KIT ASY 2 02986032 1 PLATE ASY, BACKING 3 001643 1 SHAFT, KEYED 4 NFS 1 HOUSING ASY, (NOT FURNISHED AS PARTS) 5 001644 1 BEARING & RACE SET 6 001645 1 PLATE, CAM INSERT 7 03200409 1 O-RING 8 00016200 2 HHCS 5/16NC 2 PL5 9 03200411 1 WASHER 10 02966925 1 RING, SPIRAL 11 02977420 2 RETAINING RING 12 02966926 1 KIT, SEAL ADAPTER 12A 02966924 1 O-RING, 2.0 X 1-13/16 12B 02966922 1 SEAL, HIGH PRESSURE 12C 02966923 1 SEAL ADAPTER, 2.00 BORE 13 03200521 1 STEP KEY, 1/4 X 5/16 14 03200587 1 PLUG, HEX HD # 8MB 15 002339 1 BEARING, BACKPLATE ASY 16 002340 1 BEARING HOUSING 17 02986033 1 VALVE PLATE

02986766 1 SEAL KIT

MOWER ASY - LH & RH WING 50 (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 108192 1 CUTTER HSG WLDMNT, RH 50" WING

108200 1 CUTTER HSG WLDMNT, LH 50" WING 2 ----------- 1 MOTOR ASY, WING (SEE HYD MOTOR SWCTâ€™N) 3 106458 1 PLATE,MOTOR MOUNT

00023100 2 BOLT, HEX HEAD3/8"-16UNC X 1-1/2" PL GR5 6 00019600 2 LOCKWASHER, 1/2" HEAVY 7 000673 1 PULLEY, 2 GRV 8 001761 1 HUB, 1-1/8 ID 1-13/16LG 1/4 KEY

10121000 3 BOLT, HEX HEAD 5/16"-NC X 1-1/4" PL GR5 8A 03200521 1 STEP KEY 1/4 X 5/16 9 000702 1 V-BELTS MATCHED PAIR (2 BELTS) 10 106529 1 IDLER ARM WLDMNT, RH FWD ROT.

106527 1 IDLER ARM WLDMNT, RH REV ROT

106526 1 IDLER ARM WLDMNT, LH REV ROT.

106528 1 IDLER ARM WLDMNT, LH FWD ROT. 11 103105 2 IDLER PULLEY

000001 1 BOLT, HEX HEAD 5/16"-NF X 5/8" PL GR5

00023500 1 FLATWASHER, 5/16 TYPE AW,ZP 12 101778 1 IDLER BEARING SPACER 13 000539 1 SPRING, EXTENSION

702747 1 IDLER ASY, RH (FWD ROT)

702748 1 IDLER ASY, LH (FWD ROT)

703085 1 IDLER ASY, RH (REV ROT)

703086 1 IDLER ASY, LH (REV ROT) 14 107390 1 BELT GUARD WLDMNT, RH FWD ROT

107394 1 BELT GUARD WLDMNT RH REV ROT

107386 1 BELT GUARD WLDMNT LH FWD ROT

106614 1 BELT GUARD WLDMNT, LH REV ROT

02035400 2 BOLT, HEX HEAD 3/8"-NF X 3/4" PL GR5

00011100 2 FLATWASHER, 3/8" PL STD

03101646 2 LOCKWASHER, 3/8 MEDIUM-ZP

702754 1 SUPPORT GUARD, TOP 15 103065 1 CUTTERSHAFT PULLEY 16 100768 1 KEY, CUTTERSHAFT PULLEY 17 103767 1 WASHER, 1-3/4" X 33/64" X 1/4" 18 000521 1 LOCKWASHER, HVY 5/8" 19 000407 1 BOLT, HEX HEAD 5/8"-NF X 1-1/2" ZP GR5 20 703695 1 BEARING, ASY, CUTTERSHAFT

002315 1 BEARING, CUTTERSHAFT 21 108189 1 ROLLER WLDMNT, 50", RND KEYED SHAFT 29 108186 1 CUTTERSHAFT WLDMNT, 50" CC KNIFE

MOWER ASY - LH & RH WING 50 (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

29A 108187 1 WLDMT. 50 FC CTRSHFT. 30 100759 56 USE 02986332

108381 56 KNIFE HD COARSE CUT 31 02988196 136 KNIFE, FINE CUT 32 100761 28 RING COMPLETE 33 102670 28 PIN-HARDENED 35 02668700 68 PIN COTTER 1/8 X 3/4 HAMLK 36 101034 68 KNIFE PIN HEAT TREATED< 37 103051 2 SHOE/WEAR PLATE 38 02886900 2 CARB 1/2 NC 1-1/2 PL5 39 000700 4 BOLT,PLOW 1/2NC X 1-1/2 GR5

00011700 6 HIGH ALLOY, L/W 5/16 YZ KG 40 702749 1 IDLER PIVOT PIN MA

000853 1 GREASE FTG 1/4-28 SHORT THREAD

000206 1 NO. 2 RED LUBRICAPS< 44 704305 1 BEARING, ASY

002530 1 BEARING,CUTTERSHFT (NON-DRIVE) 45 00753642 6 HEXB 3/8 NC X 1-1/4 PL5 47 00752036 6 NUT TOPLOCK 3/8 NC PL 48 000406 6 HHCS 3/8 NF 1-1/8 PL 49 000841 6 LOCKWASHER,3/8 EXTERNAL TOOTH 50 103064 1 FENDER 55 002513 1 DEFLECTOR-REAR 50 56 02153100 18 HHCS 1/4 NC 1-1/4 PL 57 00024100 18 FLATWASHER STD 1/4 PL 59 02959924 18 NUT TOPLOCK 1/4 NC PLB 60 108193 1 WDMT, FOOT GUARD 50 61 02030700 2 HHCS 1/2 NC 1 1/4 PL5

00748823 2 HHCS 1/2-13UNC 1-1/2 PL5 65 00001800 4 LOCKNUT TLM 1/2 NC PLB 66 000032 68 HHCS 5/16NF 7/8 PL5 67 02990020 136 CLIP, RING 68 000210 68 LOCKNUT CLM 5/16 NF PLB 69 02986333 136 FINE CUT RING KNIFE 70 101991 68 RING 71 703575 2 ASSY- ROLLER BRG

703976 2 ASY- ROLLER BRG W/HEX BORE

107340 2 HOUSING,BEARING,MACHINED 72 703574 2 PKG,BRG ASSY W/SETSCREW

002486 2 BEARING-REAR ROLLER W/HEX BORE 73 002039 2 ASY GREASE FTG 1/4-28 90 DEG

MOWER ASY - LH & RH WING 50 (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

74 002037 2 SEAL- ROLLER BRG 75 000516 4 CARB 1/2 NC 1-3/4 PL5 76 02979042 4 LOCKNUT,SP INSET 1/2 NC PLB 77 107182 1 USE 02976761 78 107380 1 USE 02976761 80 108185 1 OFFSET LOCKING PLATE 81 00720512 2 BOLT, 5/8-11X 2.06 GR5 -UNPLTD 82 00725916 2 NUT,CENTER LOCK,5/8NC,PL5

MOWER ASY - LH & RH WING 62 (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 107154 1 WLDMT CUTTERHSG RH 62

107155 1 WLDMT CUTTERHSG LH 62 3 106458 1 PLATE,MOTOR MOUNT

00023100 2 HHCS 3/8 -16UNC 1-1/2 PL5 6 00019600 2 LOCKWASHER, 1/2, HVY, PL 7 000673 1 PULLEY 6.35 OD 2 GRV B SEC 8 001761 1 USE 000911

10121000 3 HHCS 5/16NC 1-1/4 PL5 8A 03200521 1 STEP KEY 1/4 X 5/16 9 000702 1 V-BELTS MATCHED PAIR (2 BELTS) 10 106529 1 WLDMT,IDLER ARM RIGHT,FWD.ROT.

106527 1 WLDMT,IDLER ARM RIGHT,REV. ROT

106526 1 WLDMT,IDLER ARM LEFT,REV. ROT.

106528 1 WLDMT,IDLER ARM LEFT,FWD. ROT. 11 103105 2 IDLER PULLEY - INT<

000001 1 HHCS 5/16NF 5/8 PL5

00023500 1 FLATWASHER 5/16 PL 12 101778 1 IDLER BEARING SPACER< 13 000539 1 SPRING,EXTENSION

702747 1 ASSY,IDLER,RH (FWD ROT)

702748 1 ASSY,IDLER,LH (FWD ROT)

703085 1 ASSY,IDLER,RH (REV ROT)

703086 1 ASSY,IDLER,LH (REV ROT) 14 107390 1 WLDMT- BELT GRD RH FWD ROT

107394 1 WLDMT- BELT GUARD RH RR

107386 1 WLDMT- BELT GRD LH FWD ROT

106614 1 WLDMT,LH,BELT GUARD

02035400 2 HHCS 3/8 NF 3/4 PL5

00011100 2 FLATWASHER STD 3/8

03101646 2 HIGH ALLOY, L/W 3/8 YZ

702754 1 SUPPORT, GUARD - TOP NA 15 103065 1 CUTTERSHAFT PULLEY 16 100768 1 KEY,PULLEY,CTRSHAFT 17 103767 1 WASHER,1-3/4 X 33/64 X 1/4 18 000521 1 LOCKWASHER, 5/8 HVY, KANTLINK 19 000407 1 HHCS,5/8NF X 1-1/2 ZP5 20 703695 1 BEARING, ASY, CUTTERSHAFT

002315 1 BEARING CUTTERSHAFT 21 107176 1 WLDMT- ROLLER 62

107784 1 WLDMT- ROLLER 62 W/HEX SHAFT

MOWER ASY - LH & RH WING 62 (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

703262 1 KIT,ROLLER 60/62 29 107123 1 CUTTERSHAFT, WA CC 29A 107127 1 CUTTER SHAFT, WA FC 30 100759 72 USE 02986332

108381 72 KNIFE HD COARSE CUT 31 02988196 152 KNIFE, FINE CUT 32 100761 36 RING COMPLETE 33 102670 36 PIN-HARDENED 35 02668700 76 PIN COTTER 1/8 X 3/4 HAMLK 36 101034 76 KNIFE PIN HEAT TREATED< 37 103051 2 SHOE/WEAR PLATE 38 02886900 2 CARB 1/2 NC 1-1/2 PL5 39 000700 4 BOLT,PLOW 1/2NC X 1-1/2 GR5

00011700 6 HIGH ALLOY, L/W 5/16 YZ KG 40 702749 1 IDLER PIVOT PIN MA

000853 1 GREASE FTG 1/4-28 SHORT THREAD

000206 1 NO. 2 RED LUBRICAPS< 44 704305 1 BEARING, ASY

002530 1 BEARING,CUTTERSHFT (NON-DRIVE) 45 00753642 6 HEXB 3/8 NC X 1-1/4 PL5 47 00752036 6 NUT TOPLOCK 3/8 NC PL 48 000406 6 HHCS 3/8 NF 1-1/8 PL 49 000841 6 LOCKWASHER,3/8 EXTERNAL TOOTH 50 103064 1 FENDER 55 104682 1 DEFLECTOR,TRASH,62 (REAR) 60 107255 1 WLDMT, FOOT GUARD 62, INT 61 02030700 2 HHCS 1/2 NC 1 1/4 PL5

00748823 2 HHCS 1/2-13UNC 1-1/2 PL5 62 108742 1 BAR,FLAP RETAINER - 62" REAR 65 00001800 4 LOCKNUT TLM 1/2 NC PLB 66 000032 76 HHCS 5/16NF 7/8 PL5 67 02990020 152 CLIP, RING 68 000210 76 LOCKNUT CLM 5/16 NF PLB 69 02986333 152 FINE CUT RING KNIFE 70 101991 76 RING 71 703575 2 ASSY- ROLLER BRG

703976 2 ASY- ROLLER BRG W/HEX BORE

107340 2 HOUSING,BEARING,MACHINED 72 703574 2 PKG,BRG ASSY W/SETSCREW

002486 2 BEARING-REAR ROLLER W/HEX BORE 73 002039 2 ASY GREASE FTG 1/4-28 90 DEG

MOWER ASY - LH & RH WING 62 (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

74 002037 2 SEAL- ROLLER BRG 75 000516 4 CARB 1/2 NC 1-3/4 PL5 76 02979042 4 LOCKNUT,SP INSET 1/2 NC PLB 77 107182 1 USE 02976761 78 107380 1 USE 02976761 79 106779 1 DEFLECTOR,TRASH,62 (FRONT)

703263 1 ASSY,ROLLER BRG/BRKT,LH

703596 1 ASSY,ROLLER BRG/BRKT,RH

703977 1 ASY- ROLLER BRKT LH W/HEX BRG

703978 1 ASY- ROLLER BRKT RH W/HEX BRG 80 108185 1 OFFSET LOCKING PLATE 81 00720512 2 BOLT, 5/8-11X 2.06 GR5 -UNPLTD 82 00725916 2 NUT,CENTER LOCK,5/8NC,PL5 83 108750 2 BAR FLAP RETAINER 62 FRONT

02153100 24 HHCS 1/4 NC 1-1/4 PL

00024100 24 FLATWASHER STD 1/4 PL

02959924 24 NUT TOPLOCK 1/4 NC PLB

MOWER ASY - LH & RH WING 74 (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 107156 1 WLDMT,CTRHSG,74-RH

107157 1 WLDMT,CTRHSG,74-LH 3 106458 1 PLATE,MOTOR MOUNT

00023100 2 HHCS 3/8 -16UNC 1-1/2 PL5 4 00748823 2 HHCS 1/2-13UNC 1-1/2 PL5 5 00001800 2 LOCKNUT TLM 1/2 NC PLB 6 00019600 2 LOCKWASHER, 1/2, HVY, PL 7 000673 1 PULLEY 6.35 OD 2 GRV B SEC 8 001761 1 USE 000911

10121000 3 HHCS 5/16NC 1-1/4 PL5

00011700 3 HIGH ALLOY, L/W 5/16 YZ KG 8A 03200521 1 STEP KEY 1/4 X 5/16 9 000702 1 V-BELTS MATCHED PAIR (2 BELTS) 10 106529 1 WLDMT,IDLER ARM RIGHT,FWD.ROT.

106527 1 WLDMT,IDLER ARM RIGHT,REV. ROT

106526 1 WLDMT,IDLER ARM LEFT,REV. ROT.

106528 1 WLDMT,IDLER ARM LEFT,FWD. ROT. 11 103105 2 IDLER PULLEY - INT<

000001 1 HHCS 5/16NF 5/8 PL5

00011700 1 HIGH ALLOY, L/W 5/16 YZ KG

00023500 1 FLATWASHER 5/16 PL 12 101778 1 IDLER BEARING SPACER< 13 000539 1 SPRING,EXTENSION

702747 1 ASSY,IDLER,RH (FWD ROT)

702748 1 ASSY,IDLER,LH (FWD ROT)

703085 1 ASSY,IDLER,RH (REV ROT)

703086 1 ASSY,IDLER,LH (REV ROT)

000206 1 NO. 2 RED LUBRICAPS< 14 107390 1 WLDMT- BELT GRD RH FWD ROT

107394 1 WLDMT- BELT GUARD RH RR

107386 1 WLDMT- BELT GRD LH FWD ROT

106614 1 WLDMT,LH,BELT GUARD

02035400 2 HHCS 3/8 NF 3/4 PL5

00011100 2 FLATWASHER STD 3/8

03101646 2 HIGH ALLOY, L/W 3/8 YZ

702754 1 SUPPORT, GUARD - TOP NA

00753642 1 HEXB 3/8 NC X 1-1/4 PL5

00752036 1 NUT TOPLOCK 3/8 NC PL 15 103065 1 CUTTERSHAFT PULLEY 16 100768 1 KEY,PULLEY,CTRSHAFT

MOWER ASY - LH & RH WING 74 (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

17 103767 1 WASHER,1-3/4 X 33/64 X 1/4 18 000521 1 LOCKWASHER, 5/8 HVY, KANTLINK 19 000407 1 HHCS,5/8NF X 1-1/2 ZP5 20 703695 1 BEARING, ASY, CUTTERSHAFT

002315 1 BEARING CUTTERSHAFT 21 107177 1 WLDMT- ROLLER 74

107785 1 WLDMT- ROLLER 74 W/HEX SHAFT

703261 1 ASSY- ROLLER 74

000516 2 CARB 1/2 NC 1-3/4 PL5

02886900 2 CARB 1/2 NC 1-1/2 PL5

00001800 4 LOCKNUT TLM 1/2 NC PLB 29 107124 1 CUTTERSHAFT, CC 29A 107128 1 CUTTERSHAFT, FC WA 30 100759 72 USE 02986332

108381 72 KNIFE HD COARSE CUT 31 02988196 184 KNIFE, FINE CUT 32 100761 36 RING COMPLETE 33 102670 36 PIN-HARDENED 34 02668700 36 PIN COTTER 1/8 X 3/4 HAMLK 35 02668700 92 PIN COTTER 1/8 X 3/4 HAMLK 36 101034 92 KNIFE PIN HEAT TREATED< 37 103051 2 SHOE/WEAR PLATE 38 02886900 2 CARB 1/2 NC 1-1/2 PL5 39 000700 4 BOLT,PLOW 1/2NC X 1-1/2 GR5

00011700 6 HIGH ALLOY, L/W 5/16 YZ KG 40 702749 1 IDLER PIVOT PIN MA

000853 1 GREASE FTG 1/4-28 SHORT THREAD

000206 1 NO. 2 RED LUBRICAPS< 44 704305 1 BEARING, ASY

002530 1 BEARING,CUTTERSHFT (NON-DRIVE) 45 00753642 6 HEXB 3/8 NC X 1-1/4 PL5 47 00752036 6 NUT TOPLOCK 3/8 NC PL 48 000406 6 HHCS 3/8 NF 1-1/8 PL 49 000841 6 LOCKWASHER,3/8 EXTERNAL TOOTH 50 103064 1 FENDER 51 00748823 1 HHCS 1/2-13UNC 1-1/2 PL5 52 02030700 1 HHCS 1/2 NC 1 1/4 PL5 54 00001800 2 LOCKNUT TLM 1/2 NC PLB 55 100783 1 DEFLECTOR,TRASH,74 (REAR) 56 02153100 22 HHCS 1/4 NC 1-1/4 PL 57 00024100 22 FLATWASHER STD 1/4 PL

MOWER ASY - LH & RH WING 74 (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

59 02959924 22 NUT TOPLOCK 1/4 NC PLB 60 107257 1 WLDMT, FOOT GUARD 74, INT 61 02030700 2 HHCS 1/2 NC 1 1/4 PL5

00748823 2 HHCS 1/2-13UNC 1-1/2 PL5 62 108743 1 BAR FLAP RETAINER 74 REAR

02153100 12 HHCS 1/4 NC 1-1/4 PL

00024100 12 FLATWASHER STD 1/4 PL

02959924 12 NUT TOPLOCK 1/4 NC PLB 65 00001800 4 LOCKNUT TLM 1/2 NC PLB 66 000032 92 HHCS 5/16NF 7/8 PL5 67 02990020 184 CLIP, RING 68 000210 92 LOCKNUT CLM 5/16 NF PLB 69 02986333 184 FINE CUT RING KNIFE 70 101991 92 RING 71 703575 2 ASSY- ROLLER BRG

703976 2 ASY- ROLLER BRG W/HEX BORE

107340 2 HOUSING,BEARING,MACHINED 72 703574 2 PKG,BRG ASSY W/SETSCREW

002486 2 BEARING-REAR ROLLER W/HEX BORE 73 002039 2 ASY GREASE FTG 1/4-28 90 DEG 74 002037 2 SEAL- ROLLER BRG 75 000516 4 CARB 1/2 NC 1-3/4 PL5 76 02979042 4 LOCKNUT,SP INSET 1/2 NC PLB 77 107182 1 USE 02976761 78 107380 1 USE 02976761 79 106780 1 DEFLECTOR,TRASH,74 (FRONT)

703263 1 ASSY,ROLLER BRG/BRKT,LH

703596 1 ASSY,ROLLER BRG/BRKT,RH

703977 1 ASY- ROLLER BRKT LH W/HEX BRG

703978 1 ASY- ROLLER BRKT RH W/HEX BRG 80 108185 1 OFFSET LOCKING PLATE 81 00720512 2 BOLT, 5/8-11X 2.06 GR5 -UNPLTD 82 00725916 2 NUT,CENTER LOCK,5/8NC,PL5 83 108751 2 BAR FLAP RETAINER 74 FRONT

02153100 24 HHCS 1/4 NC 1-1/4 PL

00024100 24 FLATWASHER STD 1/4 PL

02959924 24 NUT TOPLOCK 1/4 NC PLB

MOWER ASY - LH & RH WING 88 (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 107158 1 WLDMT-CUTTERHSG RH 88

107159 1 WLDMT CUTTERHSG LH 88 3 106458 1 PLATE,MOTOR MOUNT

00023100 2 HHCS 3/8 -16UNC 1-1/2 PL5 6 00019600 2 LOCKWASHER, 1/2, HVY, PL 7 000673 1 PULLEY 6.35 OD 2 GRV B SEC 8 001761 1 USE 000911

10121000 3 HHCS 5/16NC 1-1/4 PL5 8A 03200521 1 STEP KEY 1/4 X 5/16 9 000702 1 V-BELTS MATCHED PAIR (2 BELTS) 10 106529 1 WLDMT,IDLER ARM RIGHT,FWD.ROT.

106527 1 WLDMT,IDLER ARM RIGHT,REV. ROT

106526 1 WLDMT,IDLER ARM LEFT,REV. ROT.

106528 1 WLDMT,IDLER ARM LEFT,FWD. ROT. 11 103105 2 IDLER PULLEY - INT<

000001 1 HHCS 5/16NF 5/8 PL5

00023500 1 FLATWASHER 5/16 PL 12 101778 1 IDLER BEARING SPACER< 13 000539 1 SPRING,EXTENSION

702747 1 ASSY,IDLER,RH (FWD ROT)

702748 1 ASSY,IDLER,LH (FWD ROT)

703085 1 ASSY,IDLER,RH (REV ROT)

703086 1 ASSY,IDLER,LH (REV ROT) 14 107390 1 WLDMT- BELT GRD RH FWD ROT

107394 1 WLDMT- BELT GUARD RH RR

107386 1 WLDMT- BELT GRD LH FWD ROT

106614 1 WLDMT,LH,BELT GUARD

02035400 2 HHCS 3/8 NF 3/4 PL5

00011100 2 FLATWASHER STD 3/8

03101646 2 HIGH ALLOY, L/W 3/8 YZ

002315 1 BEARING CUTTERSHAFT 21 107178 1 WLDMT- ROLLER 88

107786 1 WLDLMT- ROLLER 88 W/HEX SHAFT

MOWER ASY - LH & RH WING 88 (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

703260 1 ASY,ROLLER 88 29 107125 1 CUTTERSHAFT, CC WA 29A 107129 1 CUTTERSHAFT, BLANK 30 100759 88 USE 02986332

108381 88 KNIFE HD COARSE CUT 31 02988196 216 KNIFE, FINE CUT 32 100761 44 RING COMPLETE 33 102670 44 PIN-HARDENED 35 02668700 108 PIN COTTER 1/8 X 3/4 HAMLK 36 101034 108 KNIFE PIN HEAT TREATED< 37 103051 2 SHOE/WEAR PLATE 38 02886900 2 CARB 1/2 NC 1-1/2 PL5 39 000700 4 BOLT,PLOW 1/2NC X 1-1/2 GR5

00011700 6 HIGH ALLOY, L/W 5/16 YZ KG 40 702749 1 IDLER PIVOT PIN MA

000853 1 GREASE FTG 1/4-28 SHORT THREAD

000206 1 NO. 2 RED LUBRICAPS< 44 704305 1 BEARING, ASY

002530 1 BEARING,CUTTERSHFT (NON-DRIVE) 45 00753642 6 HEXB 3/8 NC X 1-1/4 PL5 47 00752036 6 NUT TOPLOCK 3/8 NC PL 48 000406 6 HHCS 3/8 NF 1-1/8 PL 49 000841 6 LOCKWASHER,3/8 EXTERNAL TOOTH 50 103064 1 FENDER 55 100755 1 DEFLECTOR,TRASH,88 (REAR) 60 107259 1 WLDMT, FOOT GUARD 88, INT 61 02030700 2 HHCS 1/2 NC 1 1/4 PL5

00748823 2 HHCS 1/2-13UNC 1-1/2 PL5 62 108744 1 BAR,FLAP RETAINER - 88" REAR 65 00001800 4 LOCKNUT TLM 1/2 NC PLB 66 000032 108 HHCS 5/16NF 7/8 PL5 67 02990020 226 CLIP, RING 68 000210 108 LOCKNUT CLM 5/16 NF PLB 69 02986333 216 FINE CUT RING KNIFE 70 101991 108 RING 71 703575 2 ASSY- ROLLER BRG

703976 2 ASY- ROLLER BRG W/HEX BORE

107340 2 HOUSING,BEARING,MACHINED 72 703574 2 PKG,BRG ASSY W/SETSCREW

002486 2 BEARING-REAR ROLLER W/HEX BORE 73 002039 2 ASY GREASE FTG 1/4-28 90 DEG

MOWER ASY - LH & RH WING 88 (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

74 002037 2 SEAL- ROLLER BRG 75 000516 4 CARB 1/2 NC 1-3/4 PL5 76 02979042 4 LOCKNUT,SP INSET 1/2 NC PLB 77 107182 1 USE 02976761 78 107380 1 USE 02976761 79 106781 1 DEFLECTOR,TRASH,88 (FRONT)

703263 1 ASSY,ROLLER BRG/BRKT,LH

703596 1 ASSY,ROLLER BRG/BRKT,RH

703977 1 ASY- ROLLER BRKT LH W/HEX BRG

703978 1 ASY- ROLLER BRKT RH W/HEX BRG 80 108185 1 OFFSET LOCKING PLATE 81 00720512 2 BOLT, 5/8-11X 2.06 GR5 -UNPLTD 82 00725916 2 NUT,CENTER LOCK,5/8NC,PL5 83 108752 2 BAR FLAP RETAINER 88 FRONT

02153100 24 HHCS 1/4 NC 1-1/4 PL

00024100 24 FLATWASHER STD 1/4 PL

02959924 24 NUT TOPLOCK 1/4 NC PLB

MOWER ASY - REAR 88 (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 107171 1 WLDMT,CTRHSG,88-CTR

107201 1 WLDMT CTRHSG 88 W/CASTER

107220 1 WLDMT CTRHSG 88 OFFST RT 6.5

107221 1 WLDMT CTRHSG 88 OR 6.5 W/BRKTS

107203 1 WLDMT-CTRHSG 88 O.R. 8.50

107202 1 WLDMT CTRHSG 88-OR 8.5 W/BRKTS

107204 1 WLDMT CTRHSG 88 O.R. 14.50

107205 1 WLDMT-CTRHSG 88 OR 14.5 W/BKTS

107206 1 WLDMT CTRHSG 88 OR 20.5

107207 1 WLDMT CTRHSG 88 OR 20.5 W/BRKT

107208 1 WLDMT CTRHSG 88 RENOV W/BRKTS

107209 1 WLDMT CTRHSG 88 RENV W/BRAKTS 2 702705 1 ASSY,SHLD (D/L)

00002000 4 HHCS 3/8 NC X 3/4 PL5 3 102549 1 T49 IH QUICK COTTER< 4 102658 2 WLDMT,OVERARM ASSY

02045000 2 HEXB,5/8 NC X 2-1/4 GRD5 ZP

00008300 6 HHCS 5/8 NC 1-3/4 PL5

00695100 8 LOCKNUT TOPLOCK 5/8NC PLB

000874 1 HHCS 3/4 NC 3-3/4 PL5

102667 1 A-FRAME, SPACER

00037200 1 NUT 3/4-NC TOPLOCK GRC PL 5 101779 1 PIN, HITCH 6 103715 2 A-FRAME 7 103713 1 WLDMT,GRBX MNTG FRAME 8 702673 1 GEARBOX, OILED & TESTED

700489 1 BANJO ASSY 88 CENTER,FWD/REV

700523 1 BANJO 74 CT/F/R,88 OR6.5 FWD

701457 1 BANJO ASSY 88 OFFSET 8.5 FWD

701455 1 BANJO,74 OR8,88 OR14.5 FWD

700554 1 BANJO,74 OR14;99OR20.5 FWD 9 000510 2 USE 00752658 10 000511 2 USE 02675800 11 700171 1 COUPLER, W/ZERK, SPLINED 12 100724 1 SHAFT EXTENSION

100778 1 EXTENSION SHAFT

100287 1 OUTPUT SHAFT EXT 6<

100288 1 OUTPUT SHAFT EXT 5<

100286 1 OUTPUT SHAFT EXT 4 13 100721 1 EXTENSION SHAFT HSG<

100776 1 EXTENSION SHAFT HSG<

MOWER ASY - REAR 88 (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

102804 1 EXTENSION SHAFT HSG

102874 1 EXT SHFT HSG 60 WA

102637 1 OFFSET EXT SHAFT HSG

001727 1 SCREW, FLNG HD 12PT, CTR-BORE

03101646 1 HIGH ALLOY, L/W 3/8 YZ 14 100057 1 RETAINING RING 15 100010 1 OUTPUT BEVEL RING 16 000398 1 BALL BEARING 1-1/8 BORE CYL OD

700491 1 HOUSING AND BEARING ASSEMBLY

00023100 4 HHCS 3/8 -16UNC 1-1/2 PL5 17 700739 1 BEARING HOUSING W/ZERK ASSY 18 000402 2 RETAINING RING 19 102651 3 PULLEY SHIM< 20 102501 1 PULLEY, 8.99 DIA X 1.125 BORE 21 101782 1 KEY,DRIVE PULLEY 22 101780 1 WASHER,BRG 1-7/16X33/64X3/16 24 000555 1 HHCS 1/2 NF X 1-1/2 PL5 25 100706 1 BELT 26 105597 1 BRACKET,MOUNTING,SHIELD 27 103716 1 TUBE,SPACER,LOWER ARM 28 000333 2 CLICK PIN DANUSER 1533 29 103717 2 TUBE,SPACER,UPPER ARM 30 100743 2 HITCH PIN 31 000539 1 SPRING,EXTENSION 32 101778 4 IDLER BEARING SPACER<

000001 1 HHCS 5/16NF 5/8 PL5

00011700 1 HIGH ALLOY, L/W 5/16 YZ KG

700494 1 ASSY,IDLER ARM (SHD)

701851 1 ASSY,IDLER ARM (SHD-RR) 33 701905 1 ASSY,OUTBRD BRG PLATE (SHD)

701847 1 ASSY,OUTBRD BRG PLATE (SHD-RR)

000135 1 HHCS 3/8NC X 2-1/4 PL5

000645 1 HHCS 3/8 NC 7/8 PL5

00013901 1 NUT HEX 3/8 NC PL 34 100727 1 WLDMT-IDLER ARM

104938 1 IDLER ARM W.A.

00755153 2 PIN,COTTER 3/16 X 1-1/2 PLATED 35 000547 1 PULLEY,IDLER 36 700488 1 PKG,SHPG,BELT GUARD (SHD)

701845 1 BELT GD. SHIPPING PKG.

000139 1 HHCS 1/2 NC X 1 PL5

MOWER ASY - REAR 88 (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

000508 2 HHCS - 1/2 NF X 1 GR5

00019600 2 LOCKWASHER, 1/2, HVY, PL

00019700 2 FLATWASHER STD 7/16 PL 40 107178 1 WLDMT- ROLLER 88

703260 1 ASY,ROLLER 88

107786 1 WLDLMT- ROLLER 88 W/HEX SHAFT 41 001863 1 DRIVELINE,S60 W/8 CLUTCH 42 107125 1 CUTTERSHAFT, CC WA 42A 107129 1 CUTTERSHAFT, BLANK 44 100761 44 RING COMPLETE 45 102670 44 PIN-HARDENED 46 100759 88 USE 02986332

02986276 88 KNIFE,EXTREME SERVICE

108381 88 KNIFE HD COARSE CUT

103026 44 RENOVATING KNIFE CC

700592 1 USE 02986334

701778 1 RENOVATING KNIVE PKG 88CC

02986278 1 EXTREME SERVICE, KNIFE, PKG 88 47 103051 2 SHOE/WEAR PLATE

000700 4 BOLT,PLOW 1/2NC X 1-1/2 GR5 48 703695 1 BEARING, ASY, CUTTERSHAFT

002315 1 BEARING CUTTERSHAFT 49 102652 1 PULLEY 8-3/4-1-15/16 BORE< 50 100768 1 KEY,PULLEY,CTRSHAFT 51 100720 1 WASHER, CUTTERSHAFT 52 000521 1 LOCKWASHER, 5/8 HVY, KANTLINK 53 000407 1 HHCS,5/8NF X 1-1/2 ZP5 54 703575 2 ASSY- ROLLER BRG

703976 2 ASY- ROLLER BRG W/HEX BORE

107340 2 HOUSING,BEARING,MACHINED

703574 2 PKG,BRG ASSY W/SETSCREW

002486 2 BEARING-REAR ROLLER W/HEX BORE

002039 2 ASY GREASE FTG 1/4-28 90 DEG 55 002037 2 SEAL- ROLLER BRG 58 000516 4 CARB 1/2 NC 1-3/4 PL5

000206 2 NO. 2 RED LUBRICAPS< 61 107258 1 WLDMT, FOOT GUARD 88, SHD

00749130 4 HHCS 1/2-13UNC 1-3/4 PL5 62 100755 1 DEFLECTOR,TRASH,88 (REAR) 63 000032 108 HHCS 5/16NF 7/8 PL5 64 02990020 226 CLIP, RING

MOWER ASY - REAR 88 (PART 4)

Continued... ITEM PART NO. QTY. DESCRIPTION

65 000210 108 LOCKNUT CLM 5/16 NF PLB 66 101991 108 RING 67 02986333 108 FINE CUT RING KNIFE

700803 1 USE 02986343 68 101034 108 KNIFE PIN HEAT TREATED< 69 02668700 108 PIN COTTER 1/8 X 3/4 HAMLK 70 02988196 216 KNIFE, FINE CUT

02986839 1 KIT, 226 FC KNIVES&COTTERPINS

102087 108 STRAIGHT KNIFE .083 X 1 1/4

700517 1 H387 RNVTG KN PKG 88

00023500 216 FLATWASHER 5/16 PL 71 000354 6 HHCS 3/8 NC 1-1/8 PL5 73 00752036 6 NUT TOPLOCK 3/8 NC PL 74 103064 1 FENDER 75 00748823 1 HHCS 1/2-13UNC 1-1/2 PL5 76 02030700 1 HHCS 1/2 NC 1 1/4 PL5 78 00001800 2 LOCKNUT TLM 1/2 NC PLB 79 704305 1 BEARING, ASY

002530 1 BEARING,CUTTERSHFT (NON-DRIVE) 80 106781 1 DEFLECTOR,TRASH,88 (FRONT)

02153100 12 HHCS 1/4 NC 1-1/4 PL

00024100 12 FLATWASHER STD 1/4 PL

02959924 12 NUT TOPLOCK 1/4 NC PLB 81 107182 1 USE 02976761 82 107380 1 USE 02976761

703263 1 ASSY,ROLLER BRG/BRKT,LH

703596 1 ASSY,ROLLER BRG/BRKT,RH

703977 1 ASY- ROLLER BRKT LH W/HEX BRG

703978 1 ASY- ROLLER BRKT RH W/HEX BRG

02886900 4 CARB 1/2 NC 1-1/2 PL5

02979042 4 LOCKNUT,SP INSET 1/2 NC PLB 85 108744 1 BAR,FLAP RETAINER - 88" REAR 86 108752 1 BAR FLAP RETAINER 88 FRONT

MOWER ASY - REAR 96 (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 107768 1 WLDMT,CTRHSG,96-CTR 2 702705 1 ASSY,SHLD (D/L)

000132 4 HHCS 3/8NC X 3/4 PL5 3 102549 1 T49 IH QUICK COTTER< 4 102658 2 WLDMT,OVERARM ASSY

02045000 2 HEXB,5/8 NC X 2-1/4 GRD5 ZP

000716 6 USE 00008300

00695100 8 LOCKNUT TOPLOCK 5/8NC PLB

000874 1 HHCS 3/4 NC 3-3/4 PL5 1 102667 1 A-FRAME, SPACER

00037200 1 NUT 3/4-NC TOPLOCK GRC PL 5 101779 1 PIN, HITCH 6 103715 2 A-FRAME 7 02977728 1 WDMT,GEARBOX MOUTING FRAME

103713 1 WLDMT,GRBX MNTG FRAME 8 702673 1 GEARBOX, OILED & TESTED

703946 1 BANJO ASY 96 CENTER,FWD/REV

- 703757 1 ASSY,GRBX-EXT.SHFT-BRG(BANJO) 9 000510 2 USE 00752658 10 000511 2 USE 02675800

000552 6 SHIM 11 70017 1 BEARING CUP (07100) 12 107748 1 SHAFT,OUTPUT FOR SH96

107540 1 SHAFT,OUTPUT FOR SH88,OR26.5 13 107747 1 WLDMT,HSG,EXT.SHFT,OFFSET

107541 1 WLDMT,HSG,EXT.SHFT,OFFSET 26.5

001727 1 SCREW, FLNG HD 12PT, CTR-BORE

000019 1 LOCKWASHER 3/8 MED KANTLINK 14 100010 1 OUTPUT BEVEL RING 15 100057 1 RETAINING RING 16 000398 1 BALL BEARING 1-1/8 BORE CYL OD

700491 1 HOUSING AND BEARING ASSEMBLY

000937 4 HHCS,3/8NC X 1-1/2 ZP5 17 700739 1 BEARING HOUSING W/ZERK ASSY 18 000402 2 RETAINING RING 19 102651 3 PULLEY SHIM< 20 102501 1 PULLEY, 8.99 DIA X 1.125 BORE 21 101782 1 KEY,DRIVE PULLEY 22 101780 1 WASHER,BRG 1-7/16X33/64X3/16

MOWER ASY - REAR 96 (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

24 000555 1 HHCS 1/2 NF X 1-1/2 PL5 25 100706 1 BELT 26 105597 1 BRACKET,MOUNTING,SHIELD 27 103717 1 TUBE,SPACER,UPPER ARM 28 000333 2 CLICK PIN DANUSER 1533 29 103716 2 TUBE,SPACER,LOWER ARM 30 100743 2 HITCH PIN 31 000539 1 SPRING,EXTENSION 32 101778 4 IDLER BEARING SPACER<

000001 1 HHCS 5/16NF 5/8 PL5

000018 1 LOCKWASHER 5/16 MED KANTLINK

000017 1 FLATWASHER,5/16,TYPE AW,ZP 33 701905 1 ASSY,OUTBRD BRG PLATE (SHD)

701847 1 ASSY,OUTBRD BRG PLATE (SHD-RR)

000135 1 HHCS 3/8NC X 2-1/4 PL5

000645 1 HHCS 3/8 NC 7/8 PL5

000171 1 NUT,3/8 NC HEX 34 100727 1 WLDMT-IDLER ARM

104938 1 IDLER ARM W.A.

000523 2 PIN COTTER 3/16 X 1-1/2 35 000547 1 PULLEY,IDLER

700494 1 ASSY,IDLER ARM (SHD)

701851 1 ASSY,IDLER ARM (SHD-RR) 36 700488 1 PKG,SHPG,BELT GUARD (SHD)

701845 1 BELT GD. SHIPPING PKG.

000139 1 HHCS 1/2 NC X 1 PL5

000508 2 HHCS - 1/2 NF X 1 GR5

000520 2 USE 00019600

000063 2 FLATWASHER,7/16,TYPE AW,ZP 37 103117 1 FENDER,GUARD (SHD)

104935 1 WLDMT,GUARD FENDER (SHD-RR) 38 107468 1 SPACER-CUTTERSHAFT- SHD 40 107682 1 WLDMT,ROLLER 96

107787 1 WLDMT- ROLLER 96 W/HEX SHAFT 41 001863 1 DRIVELINE,S60 W/8 CLUTCH 42 107745 1 CUTTERSHAFT, WA

107789 1 CUTTERSHAFT, WA VERSA PRO 44 100761 48 RING COMPLETE 45 102670 48 PIN-HARDENED 46 100759 96 USE 02986332

108381 96 KNIFE HD COARSE CUT

MOWER ASY - REAR 96 (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

703874A 1 PKG,KNIFE,HD CC,96 (108381)

103026 48 RENOVATING KNIFE CC 47 103051 2 SHOE/WEAR PLATE

000515 2 USE 02886900

000700 4 BOLT,PLOW 1/2NC X 1-1/2 GR5

100704 2 WLDMT,HOUSING SHOE (RENV) 48 703695 1 BEARING, ASY, CUTTERSHAFT

002315 1 BEARING CUTTERSHAFT

00752036 6 NUT TOPLOCK 3/8 NC PL 49 102652 1 PULLEY 8-3/4-1-15/16 BORE< 50 100768 1 KEY,PULLEY,CTRSHAFT 51 100720 1 WASHER, CUTTERSHAFT 52 000521 1 LOCKWASHER, 5/8 HVY, KANTLINK 53 000407 1 HHCS,5/8NF X 1-1/2 ZP5 54 703575 2 ASSY- ROLLER BRG

703976 2 ASY- ROLLER BRG W/HEX BORE

107304 2 WLDMT, SKID BAR PF-38

703574 2 PKG,BRG ASSY W/SETSCREW

002486 2 BEARING-REAR ROLLER W/HEX BORE

002039 2 ASY GREASE FTG 1/4-28 90 DEG 55 002037 2 SEAL- ROLLER BRG 58 000516 4 CARB 1/2 NC 1-3/4 PL5

000206 2 NO. 2 RED LUBRICAPS< 61 107754 1 WLDMT, FOOT GUARD 96 SHD 62 107753 1 DEFLECTOR,TRASH,96 (REAR)

000016 13 USE 00024100 63 000032 118 HHCS 5/16NF 7/8 PL5 64 02990020 246 CLIP, RING 65 000210 118 LOCKNUT CLM 5/16 NF PLB 66 101991 118 RING 67 02986333 236 FINE CUT RING KNIFE 68 101034 118 KNIFE PIN HEAT TREATED< 69 000026 118 1/8X3/4 HAMMERLOCK COTTERPN< 70 02988196 236 KNIFE, FINE CUT

102087 118 STRAIGHT KNIFE .083 X 1 1/4 71 000354 6 HHCS 3/8 NC 1-1/8 PL5 74 103064 1 FENDER 75 000141 1 HHCS 1/2NC X 1-1/2 PL5 76 000140 1 HHCS 1/2 NC X 1-1/4 PL5 79 704305 1 BEARING, ASY

MOWER ASY - REAR 96 (PART 4)

Continued... ITEM PART NO. QTY. DESCRIPTION

002530 1 BEARING,CUTTERSHFT (NON-DRIVE) 80 108017 1 DEFLECTOR,TRASH 96 FRONT

02153100 13 HHCS 1/4 NC 1-1/4 PL

00024100 13 FLATWASHER STD 1/4 PL

02959924 13 NUT TOPLOCK 1/4 NC PLB 81 107182 1 USE 02976761 82 107380 1 USE 02976761

703263 1 ASSY,ROLLER BRG/BRKT,LH

703596 1 ASSY,ROLLER BRG/BRKT,RH

703977 1 ASY- ROLLER BRKT LH W/HEX BRG

703978 1 ASY- ROLLER BRKT RH W/HEX BRG

02886900 4 CARB 1/2 NC 1-1/2 PL5 83 00749130 4 HHCS 1/2-13UNC 1-3/4 PL5 84 00001800 4 LOCKNUT TLM 1/2 NC PLB 85 02976084 1 BAR FLAP RETAINER 96 REAR 86 108753 1 BAR FLAP RETAINER 96 FRONT

OPTIONAL CASTER WHEELS - REAR MOWER LAMINATED

ITEM PART NO. QTY. DESCRIPTION

700502 1 PKG,180 LAM. CSTR WHL,FLD INSTL

701057M 1 PKG,360 LAM. CSTR WHL FLD INSTL

702883 1 PKG,CSTR,180 LAM.

702193 1 PKG,CTR,360 LAM. 11 00001300 8 LOCKWASHER,1/2 PLATED 1 100752 2 RH CASTER BRACKET 2 100753 2 LH CASTER BRACKET 3 701058M 2 CASTER, SOCKET ASY W/ZERK 360° 4 700191 2 CASTER SOCKET ASSY W/ZERK 180° 5 00749130 4 HHCS 1/2-13UNC 1-3/4 PL5 6 000170 4 UT 1/2 NC HEX PL 7 103767 2 WASHER,1-3/4 X 33/64 X 1/4 8 02985508 2 HALF FORK COMP 9 373024C 2 HUB W/BRG CUPS&GREASE FITTING 10 00752255 8 BOLT,HHCS 1/2 NF X 1 PL5 12 373024E 2 SEAL 13 00013701 4 BEARING CONE 1" ID 14 373024H 2 ASY,WHEEL & TIRE

OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 1)

ITEM PART NO. QTY. DESCRIPTION

700500 1 CASTER WHEEL PKG, PNEUMATIC 180` SWIVEL, FIELD INSTALL

701056M 1 CASTER WHEEL PKG, PNEUMATIC 360` SWIVEL, FIELD INSTALL

702882 1 PKG CSTR 180 PNEU

702192 1 PKG.CSTR 360 PNEU 1 100752 2 CSTR BRKT RH, FIELD INSTALL 2 100753 2 CSTR BRKT LH, FIELD INSTALL 3 701058M 2 CSTR SCKT ASY W/ZERK 360 DEG. 4 700191 2 CSTR SCKT ASY W/ZERK 180 DEG.

000142 4 BOLT

000520 4 LOCKWASHER

000170 4 NUT 5 000554 2 BOLT 6 000520 2 LOCKWASHER 7 103767 2 WASHER 8 100141 2 CSTR HALF FORK, LH OR RH 9 000621 2 HUB, W/ BRG CUPS 10 000226 4 BEARING CUP 11 00766771 8 NUT LUG 1/2 NF 12 000573 2 SPACER 13 000201 2 SEAL 14 000225 4 BEARING CONE

OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 2)

ITEM PART NO. QTY. DESCRIPTION

15 101780 2 WASHER 16 000122 2 NUT, SLOTTED 17 000123 2 COTTER PIN 18 000247 2 HUB CAP

000620 2 HUB COMPLETE, (ITEMS 9.12-14,18)

702272 2 FORK ASY, LOWER (ITEMS 8,9,12-18) 19 000619 2 WHEEL, (TUBE TYPE TIRE) 20 000623 2 TUBE, (TUBE TYPE TIRE) 21 000618 2 TIRE, (TUBE TYPE)

000617 2 WHEEL, TIRE & TUBE ASY

OPTIONAL EQUIPMENT - ACCESSORIES - PACKAGES

ITEM PART NO. QTY. DESCRIPTION

1 -- - OPTIONAL EQUIPMENT 2 702321 1 KNIFE GRINDER 3 700413 1 SET OF KNIFE STRGHTNG BARS 4 -- - 62" WING MOWER 5 703602 1 ROLLER SCRAPER KIT 62 6 105569 1 ROLLER,62 RUBBER (REPL BY) 7 702118 1 ROLLER, USE 703599 & 002342 8 -- - 74" WING MOWER 9 703603 1 ROLLER SCRAPER KIT 74 10 105570 1 ROLLER,74 RUBBER (REPL BY) 11 702120 1 ROLLER, USE 703600 & 002343 12 -- - 88" WING & REAR MOWER 13 703604 1 ROLLER SCRAPER KIT 88 14 105571 1 ROLLER,88 RUBBER (REPL BY) 15 702122 1 ROLLER, ASY, RUBBER 16 -- - 88" & 96" REAR MOWER

PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 00751588 5 THUMB SCREW 1/4-20UNC-3/4LG 2 00024100 5 FLATWASHER STD 1/4 PL 3 00013300 8 HEXB 1/2 NC 2 PL5 4 00001800 11 LOCKNUT TLM 1/2 NC PLB 6 02968879 1 CAP, ASY, FILLER/BREATHER 7 02962963 1 DIAL INDICATOR-IN TANK FILTER 8 00752036 1 NUT TOPLOCK 3/8 NC PL 9 02967127 1 O-RING 10 00012101 4 LOCKWASHER, 3/8, HVY, PL 11 000645 4 HHCS 3/8 NC 7/8 PL5 12 02962617 1 FILTER ASSY W/ SHORT EXT TUBE

02961001 1 FILTER ELEMENT

02972678 1 SPRING FILTER CARTRIDGE

02973782 1 VALVE FILTER BYPASS FOR MPF184

02978349 1 FILTER COVER,FOR 02961000

02961452 1 O-RING

02978354 1 SEAL KIT FOR 02961000

02978355 1 KIT NUTS AND BOLTS FOR 0296100 13 72414000 1 ADAPTER PIPE,1-1/4 CLOSE NIPPL 14 00751468 1 ADP PIPE TEE 1-1/4FP 16 00751471 1 ADP PIPE,REDUCER,20MP-16FP 17 001784 1 BUSHING-REDUCER 16MP-8FP 18 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1 19 02958920 1 ADP HYD ELBOW 20MP -20MJIC 90

02960408 1 ADP HYD 20MP - 20MJ 45? 21 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1 23 02968880 1 GAUGE,SIGHT/TEMPERATURE 24 000810 1 THERMOMETER 20-240 DEGREE 25 00753642 1 HEXB 3/8 NC X 1-1/4 PL5 26 106513 1 BRACKET, BELT TENSION 27 00011100 1 FLATWASHER STD 3/8 28 106599 1 PULLEY 9/16 BORE 1/8 X 3/16 KW 29 106581 1 WLDMT,PULLEY 7/8-13 SPLINE 31 ---------- 4 REBUILT CYLINDER HEADOL EXCH 1 32 ---------- 4 REBUILT CYLINDER HEADOL EXCH 1 35 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1 33 001859 1 HOSE #6 - 6FJX - 4MP - 19LG 36 00751505 2 HOSE CLAMP FOR #12 HOSE 37 001796 2 FITG HOSE BIB #12HOSE-#12MP 38 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1

02980134 1 BEARING 7/8" INTERSTATER D/L

PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

02979636 1 BEARING 1" INTERSTATER D/L 39 001184 1 ADP,PIPE,COUPLER,12FP-12FP 40 02981119 1 WLDMT, TANK INTERSTATER 41 000889 1 PUMP-WEBSTER 43YB032-2L

000010 4 HHCS 3/8 NF 7/8 PL5

03101646 4 HIGH ALLOY, L/W 3/8 YZ 42 02026200 1 HOSE CLAMP,1-5/16 TO 2-1/ 4 43 03200300 1 HOSE BIB FITTING- 20MP-20 HOSE 44 02961115 1 ADP,PIPE,20FP-20FP,90DEG 46 001783 1 HOSE #20-20FJX90-BLANK-13LG 49 000141 2 HHCS 1/2NC X 1-1/2 PL5

00019600 2 LOCKWASHER, 1/2, HVY, PL 52 00755650 1 ASSY,SINGLE FRONT PUMP 2.77CID

001827 1 ASSY,SINGLE FRONT PUMP 2.28CID 54 002345 1 KEY 1/8 X 3/16 X 1 LONG 53 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1 56 106572 1 WLDMT,BUMPER 57 02981124 1 TANK COVER WLDMT. INT 58 001798 1 ADP HYD ELBOW 12FPX- 8MP 90 59 001767 1 BELT,DRIVE (5L260) 60 00751596 1 ADP HYD ELBOW 4MP-4FP90 62 001573 1 ADP HYD,6MB-6MJ,STRAIGHT 63 00751003 1 PLUG, PIPE 1/4 NPTM STANDARD 64 02959154 1 ADP HYD ELBOW 16MJ -16FJX 45 65 001891 1 ADP HYD ELBOW 4MP - 6MJ 67 02043600 1 ADP HYD ELBOW 16MB -16MJ 45 69 02961098 1 ADP HYD ELBOW 20MB -20MJ 90 71 63078500 1 PIPE CAP 20 FP 72 00751984 6 STARWSHR #10 EXT TOOTH TY A PL 73 02969917 6 MACH METRIC 5-P0.8 - 12MM

PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 00751588 5 THUMB SCREW 1/4-20UNC-3/4LG 2 00024100 5 FLATWASHER STD 1/4 PL 3 00013300 8 HEXB 1/2 NC 2 PL5 4 00001800 11 LOCKNUT TLM 1/2 NC PLB 6 02968879 1 CAP, ASY, FILLER/BREATHER 7 02962963 1 DIAL INDICATOR-IN TANK FILTER 8 00752036 1 NUT TOPLOCK 3/8 NC PL 9 02967127 1 O-RING 10 02049500 4 LOCKWASHER 3/8 HIGHCOLLAR 11 000645 4 HHCS 3/8 NC 7/8 PL5 12 02962617 1 FILTER ASSY W/ SHORT EXT TUBE

02961001 1 FILTER ELEMENT

02972678 1 SPRING FILTER CARTRIDGE

02973782 1 VALVE FILTER BYPASS FOR MPF184

02978349 1 FILTER COVER,FOR 02961000

02961452 1 O-RING

02978354 1 SEAL KIT FOR 02961000

02978355 1 KIT NUTS AND BOLTS FOR 0296100 13 72414000 1 ADAPTER PIPE,1-1/4 CLOSE NIPPL 14 00751468 2 ADP PIPE TEE 1-1/4FP 16 00751471 1 ADP PIPE,REDUCER,20MP-16FP 17 63081000 1 REDUCER BUSHING 16MP-8FP 18 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1 19 02958920 1 ADP HYD ELBOW 20MP -20MJIC 90

02960408 1 ADP HYD 20MP - 20MJ 45? 21 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1 23 02968880 1 GAUGE,SIGHT/TEMPERATURE 24 000810 1 THERMOMETER 20-240 DEGREE 25 00753642 1 HEXB 3/8 NC X 1-1/4 PL5 26 106513 1 BRACKET, BELT TENSION 27 00011100 1 FLATWASHER STD 3/8 28 106599 1 PULLEY 9/16 BORE 1/8 X 3/16 KW 29 702785 1 ASSY,PULLEY 30 00752228 1 PIN,SPIROL 3/8 X 1-1/2 31 ---------- 4 REBUILT CYLINDER HEADOL EXCH 1 32 ---------- 4 REBUILT CYLINDER HEADOL EXCH 1 33 001788 2 HOSE #6 - 6FJX - 4MP - 13LG 35 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1 36 00751505 2 HOSE CLAMP FOR #12 HOSE 37 001796 2 FITG HOSE BIB #12HOSE-#12MP 38 ---------- 1 REBUILT CYLINDER HEADOL EXCH 1

PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 2)

Alamo 803213P User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual