Alamo 02988075P User Manual

Boom Arm

Rev 02-12 Part No.02988075P

PART'S MANUAL

An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (800-356-6286) to obtain a Free copy before operating the equipment.

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 210-372-3551

TO THE OWNER/OPERATOR/DEALER

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that

you retain. The use of "will-t" parts will void your warranty and can cause catastrophic failure with possible injury or death.

BOLT TORQUE

Mounting procedures for mowers will require a signicant amount of bolt nut and washer installation.

Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness.

Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart.

Bolt tightness should be completed with and checked with a suitable torque wrench.

Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual.

Loose bolts on a frame or in a casting may be a result of:

● Vibration from the mower due to imbalance of the mower blades

● Pulled threads due to over tightening

● Distortion of the hole due to under tightening during installation

Bolts broken or sheared in the mounting structure or tractor may be the result of:

● Improper alignment of the Mounting Plate or Structure such that it is not sitting at on the mating surface

● Distortion of the bolt due to over-tightening

● Under tightening of the bolts

Check the bolt torque during installation and prior to delivery with a suitable torque wrench.

PARTS

SECTION

Parts Section – 1

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and

are subject to special handling. Request a quotation for such parts before sending a Purchase

Order.

6. The Manufacturer reserves the right to change prices without prior notice.

For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:

ALAMO INDUSTRIAL

1502 E. Walnut Seguin, Texas 78155 830-379-1480

Parts Section – 2

PART NAME INDEX

48 IN FLAIL - HEAD ASY (SOLID MNT) (PART 1).................................................................................................................................. 6

48 IN FLAIL - HEAD ASY (SOLID MNT) (PART 2)................................................................................................................................. 8

48 IN FLAIL - HEAD ASY (SWIVEL MNT) (PART 1)............................................................................................................................ 10

48 IN FLAIL - HEAD ASY (SWIVEL MNT) (PART 2)............................................................................................................................ 12

48 IN FLAIL - HEAD ASY (SWIVEL MNT) (PART 3)............................................................................................................................ 14

48 IN FLAIL - ROTOR W/KNIVES........................................................................................................................................................... 16

50 IN ROTARY - BLADE BAR ASY......................................................................................................................................................... 17

50 IN ROTARY - BLADE BAR HEAD ASY (SOLID MNT)................................................................................................................... 18

50 IN ROTARY - BLADE BAR HEAD ASY (SWIVEL MNT)................................................................................................................ 20

50 IN ROTARY - BLADE BAR HEAD SUB-ASY (SOLID MNT).......................................................................................................... 22

50 IN ROTARY - BLADE BAR HEAD SUB-ASY (SWIVEL MNT)....................................................................................................... 24

50 IN ROTARY - BLADE PAN HEAD ASY (SOLID MNT)................................................................................................................... 26

50 IN ROTARY - BLADE PAN HEAD ASY (SWIVEL MNT)................................................................................................................ 28

50 IN ROTARY - BLADE PAN HEAD SUB-ASY (SOLID MNT).......................................................................................................... 30

50 IN ROTARY - BLADE PAN HEAD SUB-ASY (SWIVEL MNT)....................................................................................................... 32

60 IN ROTARY - BLADE BAR ASY......................................................................................................................................................... 34

60 IN ROTARY - BLADE BAR HEAD ASY (SOLID MNT)................................................................................................................... 36

60 IN ROTARY - BLADE BAR HEAD ASY (SWIVEL MNT)................................................................................................................ 38

60 IN ROTARY - BLADE BAR HEAD SUB-ASY (SOLID MNT).......................................................................................................... 40

60 IN ROTARY - BLADE BAR HEAD SUB-ASY (SWIVEL MNT)....................................................................................................... 42

60 IN ROTARY - MOTOR (PARTS) (MODEL NO. 322-9210-036)........................................................................................................ 44

60 IN ROTARY - MOTOR (PARTS) (MODEL NO. 323-9210-194)........................................................................................................ 46

48 IN BUZZBAR - 2 BLADES (PART 1).................................................................................................................................................. 48

48 IN BUZZBAR - 2 BLADES (PART 2).................................................................................................................................................. 50

69 IN BUZZBAR - 3 BLADES - STD HEAD (PART 1)........................................................................................................................... 52

69 IN BUZZBAR - 3 BLADES - STD HEAD (PART 2)........................................................................................................................... 54

90 IN BUZZBAR - 4 BLADES - STD HEAD (PART 1)........................................................................................................................... 56

90 IN BUZZBAR - 4 BLADES - STD HEAD (PART 2)........................................................................................................................... 58

BUZZ BAR SPINDLE ASSEMBLY........................................................................................................................................................... 60

BUZZ BAR - HYD MOTOR PARTS - P/N 02975175............................................................................................................................... 62

BOOM ASY - 18 FT BOOM (PART 1)...................................................................................................................................................... 64

BOOM ASY - 18 FT BOOM (PART 2)...................................................................................................................................................... 66

BOOM ASY - 22 FT BOOM (PART 1)...................................................................................................................................................... 68

BOOM ASY - 22 FT BOOM (PART 2)...................................................................................................................................................... 70

BOOM ASY - 25 FT BOOM (PART 1)...................................................................................................................................................... 72

BOOM ASY - 25 FT BOOM (PART 2)...................................................................................................................................................... 74

BOOM ASY - 28FT TELESCOPING BOOM (PART 1)........................................................................................................................... 76

BOOM ASY - 28FT TELESCOPING BOOM (PART 2)........................................................................................................................... 78

COMMON CRATE COMPONENTS - ELECT VALVE........................................................................................................................... 80

COMMON CRATE COMPONENTS - MAN VALVE (PART 1)............................................................................................................. 82

PART NAME INDEX

COMMON CRATE COMPONENTS - MAN VALVE (PART 2)............................................................................................................. 84

COMMON CRATE COMPONENTS 28FT TELESCOPING - ELECT VALVE...................................................................................... 86

COMMON CRATE COMPONENTS 28FT TELESCOPING - MANUAL VALVE................................................................................ 88

DECALS - 18-22-25 FT BOOM.................................................................................................................................................................. 90

DECALS - 28FT TELESCOPING BOOM.................................................................................................................................................. 91

DECALS - 48 IN BUZZBAR - 2 BLADES................................................................................................................................................ 92

DECALS - 48 IN FLAIL HEAD.................................................................................................................................................................. 94

DECALS - 50 & 60 IN ROTARY HEAD................................................................................................................................................... 96

DECALS - 69 IN BUZZBAR - 3 BLADES................................................................................................................................................ 97

DECALS - 90 IN BUZZBAR - 4 BLADES................................................................................................................................................ 98

DECALS - HYD TANK & PUMP - ELECT VALVE................................................................................................................................ 99

DECALS - HYD TANK & PUMP - MAN VALVE................................................................................................................................. 100

DECALS - UNDER MOUNT COUNTER WEIGHT - CAST.................................................................................................................. 101

DECALS - UNDER MOUNT COUNTER WEIGHT - WELDED........................................................................................................... 102

DECALS - VALVE MAN HANDLE OPERATION................................................................................................................................ 103

DITCHER ASSEMBLY............................................................................................................................................................................ 104

DIVERTER VALVE - DOOR & SWIVEL............................................................................................................................................... 106

FILTER ASY - PN 02964748.................................................................................................................................................................... 107

HOSE ROUTING - 18 FT BOOM............................................................................................................................................................. 108

HOSE ROUTING - 18 FT BOOM NOTES............................................................................................................................................... 109

HOSE ROUTING - 22 FT BOOM............................................................................................................................................................. 110

HOSE ROUTING - 22 FT BOOM NOTES............................................................................................................................................... 111

HOSE ROUTING - 25 FT BOOM............................................................................................................................................................. 112

HOSE ROUTING - 25 FT BOOM NOTES............................................................................................................................................... 113

HOSE ROUTING - 28FT TELESCOPING BOOM.................................................................................................................................. 114

HOSE ROUTING - 28FT TELESCOPING BOOM (NOTES)................................................................................................................. 115

HOSE ROUTING - SWING CYL (18-22 FT BOOM).............................................................................................................................. 116

HYD CYL ASY - DIPPER (18 FT BOOM).............................................................................................................................................. 117

HYD CYL ASY - DIPPER (22 FT BOOM).............................................................................................................................................. 118

HYD CYL ASY - EXTENSION (28FT TELESCOPING BOOM).......................................................................................................... 119

HYD CYL ASY - HEAD SWIVEL........................................................................................................................................................... 120

HYD CYL ASY - LIFT (18-22 FT BOOM).............................................................................................................................................. 121

HYD CYL ASY - SWING W/ SPHERICAL ROD END.......................................................................................................................... 122

HYD CYL ASY - TILT (18-22 FT BOOM).............................................................................................................................................. 123

HYD CYL ASY - TILT (28FT TELESCOPING BOOM)........................................................................................................................ 124

HYD OIL COOLER & FAN ASY............................................................................................................................................................. 125

HYD SCHEMATIC - SOLID MNT HEAD (OPT) 28FT TELESCOPING BOOM................................................................................ 126

HYD SCHEMATIC - SWIVEL MNT HEAD (OPT) 28FT TELESCOPING BOOM............................................................................. 127

HYD SCHEMATIC - SOLID MNT HEAD (STD) - 18-22 FT BOOM.................................................................................................... 128

PART NAME INDEX

HYD SCHEMATIC - SWIVEL MNT HEAD (OPT) - 18-22 FT BOOM................................................................................................ 129

HYD TANK SUB-ASY............................................................................................................................................................................. 130

HYD TANK W-PUMP & ELECT VALVE ASY - 18-22 FT BOOM...................................................................................................... 132

HYD TANK W-PUMP & ELECT VALVE ASY 28FT TELESCOPING BOOM................................................................................... 134

HYD TANK W-PUMP & MAN VALVE ASY - 18-22 FT BOOM......................................................................................................... 136

HYD TANK W-PUMP & MAN VALVE ASY 28FT TELESCOPING BOOM...................................................................................... 138

PUMP ASY - SERVO CONTROLLED.................................................................................................................................................... 140

CUTTER CONTROL VALVE BLOCK.................................................................................................................................................... 142

PUMP-TANK-VALVE COVER............................................................................................................................................................... 143

JOYSTICK CONSOLE ASY..................................................................................................................................................................... 144

SPINDLE ASSEMBLY - ROTARY HEAD............................................................................................................................................. 146

WIRE HARNESS - JOYSTICK RESISTER (OPT).................................................................................................................................. 148

UNDER MOUNT COUNTER WEIGHT - CAST.................................................................................................................................... 150

UNDER MOUNT COUNTER WEIGHT - WELDED.............................................................................................................................. 151

UNDER MOUNT FRAME ASY (PART 1).............................................................................................................................................. 152

UNDER MOUNT FRAME ASY (PART 2).............................................................................................................................................. 154

VALVE ASSEMBLY - ELECTRO-HYDRAULIC VALVE................................................................................................................... 156

VALVE ASSEMBLY - MANUAL-HYDRAULIC VALVE.................................................................................................................... 158

WIRE HARNESS (ELECT-HYD VALVE OPT)..................................................................................................................................... 160

WIRE HARNESS (ELECT-HYD VALVE OPT) 28 FT TELESCOPING BOOM.................................................................................. 162

WIRE HARNESS (MAN-HYD VALVE STD)......................................................................................................................................... 164

WIRE HARNESS (SWIVEL HEAD OPT)............................................................................................................................................... 166

48 IN FLAIL - HEAD ASY (SOLID MNT) (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986253 1 ASY,48" FLAIL AXE, GEAR 1 02970301 1 WLDMT, FLAIL AXE HEAD 2 02957655M 1 ASY, CUTTERSHAFT, 48" F/A

02958540 1 FLAIL BLADE SET

02956949 16 HANGER BOLT

02980976 16 LOCKNUT, CENTERLOCK 5/8 NC PLC 3 02970465 1 WLDMT DOOR, 48" FLAIL AXE 4 02973544 1 WLDMT, MOTOR MOUNT 5 02970709 1 PLATE, COVER FLAIL AXE 6 10119000 2 HHCS 5/16 NC 1 PL5 7 00023500 6 FLATWASHER 5/16, TYPE AW, ZP 8 00750940 2 NUT, TOPLOCK 5/16 NC PL B 9 02958131 2 FLANG BEARING ASY 10 02956714 1 CLAMP BAR 11 02956712 1 RUBBER FLAP 12 02970326 1 ROD-HINGE, F/A DOOR 13 02958198 1 1/2 X 1/2 X 1 7/8 LG 14 02970585 1 WLDM SKIDSHOE INSIDE FLAIL AXE 15 02956748 1 SKID SHOE WLDMT 16 02970540 1 WLDMT - REAR ROLLER 17 02967325 2 PULLEY, 3G5V - 8.50 DIA 18 02970325 1 PLATE-BELT & PULLEY COVER 19 02972442 1 FLAIL AXE BEARING GUARD 20 02675800 2 HHCS 5/8 X 1-1/2 PL GR5 21 00010300 2 LOCKWASHER 5/8 22 00001400 4 FLATWASHER 5/8 PL STD 23 02892000 8 HHCS, 1/2"-13 NC X 1-1/2" PL8 24 00001800 13 LOCKNUT TLM 1/2 NC PL8 25 00752670 1 GREASE FITTING 1/4-28 BOLT THD 26 00008300 6 BOLT, HHCS 5/8" NC X 1-3/4" PL5 27 00695100 5 LOCKNUT TOPLOCK 5/8NC PLB 28 02970710 1 CYL, DOOR, 48" F/A 29 02970324 1 PLATE-CLAMP, HITCHPOST 30 00000941 1 GREASE ZERK 1/4-28 90 BOLT THD 31 02970583 4 SHCS 3/8 NF 1-1/2 PL GR5 32 23504500 8 JAMNUT 3/8 NF 33 03200925 1 CARR 5/8 NC X 3 PL GR5 34 02967328 1 BUSHIN, QD HUB SF 1-15/16 ID 35 02970537 1 BUSHING, QD HUB SF 1 ID 36 00013500 3 NUT, 3/8 NC JAMNUT 37 02970539 3 V BELT

48 IN FLAIL - HEAD ASY (SOLID MNT) (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

38 02956768 2 PIN, ROLL 5/32X1 39 00011700 4 LOCKWASHER 5/16 PL STD 40 00035900 4 HHCS 5/16 NC X 3/4 GR5 41 000642 7 NUT,1/2NF CENTERLOCK 42 00002700 7 FLATWASHER, 1/2 PL STD 43 00019300 7 HHCS 1/2 NF 1-1/2 PL5 44 02957041 2 ROLLER BEARING & FLANGE 45 00013300 4 BOLT, HHCS 1/2" NC X 2" PL5 46 02972949 2 BOLT 3/8 NC GR8 X 1-1/4 47 02970586 2 WASHER, 2 X 7/16 X 3/16 48 02977955 4 HHCS 3/8 NC 1-1/2 PL8 49 00015800 4 LOCKNUT TLM 3/8 NC PLC 50 00003300 1 HHCS 3/4" X 4" LG 51 00037200 7 NUT 3/4 NC LOCKNUT 52 00008200 1 BOLT, HHCS 1/2" NC X 3-3/4" PL5 53 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 54 02918600 6 HHCS 3/4 NC 2 PL8 55 02981757 2 WELDMENT, PIN, HITCH POST 56 02971702 1 FLATWASHER, 1-3/8 TYPE B PL NARROW 57 02971701 1 NUT, SLOTTED 1-3/8 12NF PLB 58 00165020 1 PIN, COTTER 5/16 X 2-1/2 PL 59 02968896 1 PLASTIC TIE, ORANGE, 11LG 60 02968894 1 PLASTIC TIE, RED, 11LG 61 02986218 1 WELDMENT, HITCHPOST 62 02984470 2 STOP, FLAIL AXE SWIVEL 63 00021400 2 BOLT, HHCS 1/4" NC X 3/4" PL 64 02959924 2 NUT, TOPLOCK 1/4 NC PLB 65 02968836 1 PLASTIC TIE, YELLOW 66 02968837 1 PLASTIC TIE, YELLOW & WHITE 67 03710151 4 METAL TACK 68 02971498 1 PLATE, S/N FLAIL AXE 48" 69 02987315 1 GEAR MOTOR 70 00749103 2 #20 SPLIT FLANGE KIT 71 02754100 2 ADP HYD ELBOW 20FL-16MJ90 72 02961286 2 20FJX - 16MJ ST 73 00011400 2 BOLT, HHCS 3/8 NC 1 PL5

48 IN FLAIL - HEAD ASY (SWIVEL MNT) (PART 1)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986251 1 48" FLAILAXE GEAR SWIVEL 1 02970301 1 WLDMT, FLAIL AXE HEAD 2 02957655M 1 ASY, CUTTERSHAFT, 48" F/A

02958540 1 FLAIL BLADE SET

02956949 16 HANGER BOLT

02980976 16 LOCKNUT, CENTERLOCK 5/8 NC PLC 3 02970465 1 WLDMT DOOR, 48" FLAIL AXE 4 02973544 1 WLDMT, MOTOR MOUNT 5 02970709 1 PLATE, COVER FLAIL AXE 6 10119000 2 HHCS 5/16 NC 1 PL5 7 00023500 6 FLATWASHER 5/16, TYPE AW, ZP 8 00750940 2 NUT, TOPLOCK 5/16 NC PL B 9 02958131 2 FLANG BEARING ASY 10 02956714 1 CLAMP BAR 11 02956712 1 RUBBER FLAP 12 02970326 1 ROD-HINGE, F/A DOOR 13 02958198 1 1/2 X 1/2 X 1 7/8 LG 14 02970585 1 WLDM SKIDSHOE INSIDE FLAIL AXE 15 02956748 1 SKID SHOE WLDMT 16 02970540 1 WLDMT - REAR ROLLER 17 02967325 2 PULLEY, 3G5V - 8.50 DIA 18 02970325 1 PLATE-BELT & PULLEY COVER 19 02972442 1 FLAIL AXE BEARING GUARD 20 02675800 2 HHCS 5/8 X 1-1/2 PL GR5 21 00010300 2 LOCKWASHER 5/8 22 00001400 4 FLATWASHER 5/8 PL STD 23 02892000 23 HHCS, 1/2"-13 NC X 1-1/2" PL8 24 00001800 13 LOCKNUT TLM 1/2 NC PLB 25 00752670 1 GREASE FITTING 1/4-28 BOLT THD 26 00008300 6 BOLT, HHCS 5/8" NC X 1-3/4" PL5 27 00695100 5 LOCKNUT TOPLOCK 5/8NC PLB 28 02970710 1 CYL, DOOR, 48" F/A 29 02970324 1 PLATE-CLAMP, HITCHPOST 30 00000941 1 GREASE ZERK 1/4-28 90 BOLT THD 31 02970583 4 SHCS 3/8 NF 1-1/2 PL GR5 32 23504500 8 JAMNUT 3/8 NF 33 03200925 1 CARR 5/8 NC X 3 PL GR5 34 02967328 1 BUSHIN, QD HUB SF 1-15/16 ID 35 02970537 1 BUSHING, QD HUB SF 1 ID 36 00013500 3 NUT, 3/8 NC JAMNUT 37 02970539 3 V BELT

48 IN FLAIL - HEAD ASY (SWIVEL MNT) (PART 2)

Continued... ITEM PART NO. QTY. DESCRIPTION

38 02956768 2 PIN, ROLL 5/32X1 39 00011700 4 LOCKWASHER 5/16 PL STD 40 00035900 4 HHCS 5/16 NC X 3/4 GR5 41 000642 7 LOCKNUT TLM 1/2 NC PLB 42 00002700 7 FLATWASHER, 1/2 PL STD 43 00019300 7 HHCS 1/2 NF 1-1/2 PL5 44 02957041 2 ROLLER BEARING & FLANGE 45 00013300 4 BOLT, HHCS 1/2" NC X 2" PL5 46 02972949 2 BOLT 3/8 NC GR8 X 1-1/4 47 02970586 2 WASHER, 2 X 7/16 X 3/16 48 02977955 4 HHCS 3/8 NC 1-1/2 PL8 49 00015800 4 LOCKNUT TLM 3/8 NC PLC 50 00003300 1 HHCS 3/4" X 4" LG 51 00037200 13 NUT 3/4 NC LOCKNUT 52 00008200 1 BOLT, HHCS 1/2" NC X 3-3/4" PL5 53 02960018 4 ADP, HYD, ELBOW, 4MB-4MJ90 54 02918600 10 HHCS 3/4 NC 2 PL8 55 02981757 2 WELDMENT, PIN, HITCH POST 56 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 57 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 58 00165020 2 PIN, COTTER 5/16 X 2-1/2 PL 59 02968896 1 PLASTIC TIE, ORANGE, 11LG 60 02968894 1 PLASTIC TIE, RED, 11LG 61 02984370 1 ADP, SWIVEL, FLAIL AXE 62 02981318 1 BEARING, 12OD X 5.8ID 63 02985319 1 WELDMENT, HITCH POST 64 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 65 02984374 1 WLDMNT, SWIVEL, CYL BRKT 66 02981820 12 SHCS 1/2 NC X 1 1/2" LG PL8 67 02963646 1 HHCS 3/4 NC 2-1/2 PL8 68 00754105 1 HHCS 3/4 NC 4 1/2 PL8 69 02984382 1 CLAMP, PLATE, SWIVEL 70 02984470 2 STOP, FLAIL AXE SWIVEL 71 00021400 2 BOLT, HHCS 1/4" NC X 3/4" PL 72 02959924 2 NUT, TOPLOCK 1/4 NC PLB 73 02968832 1 PLASTIC TIE, GREEN 74 02968833 1 PLASTIC TIE, GREEN & WHITE 75 02968836 1 PLASTIC TIE, YELLOW 76 02968837 1 PLASTIC TIE, YELLOW & WHITE 77 03710151 4 METAL TACK 78 02971498 1 PLATE, S/N FLAIL AXE 48"

48 IN FLAIL - HEAD ASY (SWIVEL MNT) (PART 3)

Continued... ITEM PART NO. QTY. DESCRIPTION

79 02987315 1 GEAR MOTOR 80 00749103 2 #20 SPLIT FLANGE KIT 81 02985030 2 ADP HYD 20FL-20MJ FLANGE 82 02961286 2 20FJX - 16MJ ST 83 00011400 2 BOLT, HHCS 3/8 NC 1 PL5

48 IN FLAIL - ROTOR W/KNIVES

ITEM PART NO. QTY. DESCRIPTION

02957655 1 ROTOR W/KNIVES ASY 1 02958540 1 KIT - BLADE, FLAIL AXE 2 02956943 32 FLAIL HANGER BUSHING 3 02956949 16 HHCS HANGER BOLT PER DWG 4 02980976 16 LOCKNUT,CENTERLOCK 5/8 NC PLC

50 IN ROTARY - BLADE BAR ASY

ITEM PART NO. QTY. DESCRIPTION

02982906 1 ASY, BLADE BAR W/BLADES 1 02982912 1 LEAF, MIDDLE, BLADE BAR 2 02982913 1 LEAF, BOTTOM, BLADE BAR 3 02962635 2 BLADE, CW ROTATION 4 02982934 1 WLDMT. TOP BLADE BAR 5 02782900 2 BOLT, BLADE 6 02957089 2 LOCKWASHER 1-1/8 PL STD 7 00020900 2 NUT, SLOTTED, HVY,1-1/8NF PL GR5 8 00023200 2 PIN, ROLL, 3/16X1-3/4 9 15C2000 4 WASHER, 1.375 X 2.50 X .165, HARDENED 10 02969235 2 HHCS, 1-1/4X3 PL GR8 11 02969236 2 HHCS, 1-1/4X2-1/4 PL GR8

50 IN ROTARY - BLADE BAR HEAD ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986211 1 ASY, 50" ROT, GEAR, BAR 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 34 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981757 2 WELDMENT, PIN, HITCH POST 14 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 15 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 16 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 17 651102 1 PIN-DRILLED 18 02976448 1 PIN - MACHINED HEAD 19 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 20 02968837 1 PLASTIC TIE, YELLOW & WHITE 21 02968836 1 PLASTIC TIE, YELLOW 22 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 55 02968894 1 PLASTIC TIE, RED, 11LG 56 02968896 1 PLASTIC TIE, ORANGE, 11LG

02968874 1 MOTOR PRESSURE HOSE (RED)

02969463 1 MOTOR RETURN HOSE (ORANGE)

02968877 1 DOOR BASE HOSE (YELLOW/WHITE)

02968878 1 DOOR ROD HOSE (YELLOW)

02981844 1 SWIVEL ROD HOSE (GREEN)

02981845 1 SWIVEL BASE HOSE (GREEN/WHITE)

50 IN ROTARY - BLADE BAR HEAD ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

02986213 1 ASY, 50" ROT,GEAR,BAR,SWIVEL 1 02961480A 1 HYD CYLINDER 2BORE X 9-1/4 STROKE 2 02982914 1 WELDMENT, DOOR 3 02982915 1 ROD, HINGE 4 99338S 2 PIN ROLL 1/4 X 3/4 5 02982919 2 FLAP, 8 1/2 X 52 X 1/4 THK 6 02982918 1 BAR, HOLD DOWN, FLAP 7 02982920 2 FLAP, REAR 10 X 53 X 3/8 THK 8 02982921 1 BAR, CLAMP, REAR 9 00011100 36 FLATWASHER 3/8 STD 10 00023100 11 HHCS 3/8 X 1-1/2 NC PL GR5 11 00015800 20 LOCKNUT TLM 3/8 NC PLC 12 00007000 9 HHCS 3/8 NC 1-3/4 PL5 13 02981315 1 CYLINDER, 2.5B X 1.5R X 14.38S 14 02981757 2 WELDMENT, PIN, HITCH POST 15 02971702 2 FLATWASHER, 1-3/8 TYPE B PL NARROW 16 02971701 2 NUT, SLOTTED 1-3/8 12NF PLB 17 165020 2 PIN, COTTER 5/16 X 2-1/2 PL 18 651102 1 PIN-DRILLED 19 02976448 1 PIN - MACHINED HEAD 20 00755153 2 PIN, COTTER 3/16 X 1-1/2 PL 21 00754105 1 HHCS 3/4 NC 4-1/2 PL8 22 02963646 3 HHCS 3/4 NC 2-1/2 PL8 23 00037200 18 NUT 3/4 NC LOCKNUT 24 02968837 1 PLASTIC TIE, YELLOW & WHITE 25 02968836 1 PLASTIC TIE, YELLOW 26 02960018 2 ADP, HYD, ELBOW, 4MB-4MJ90 27 02968832 1 PLASTIC TIE, GREEN 28 02968833 1 PLASTIC TIE, GREEN & WHITE 29 03200762 2 ADP, HYD 6MB-4MJ 90 30 02968894 1 PLASTIC TIE, RED, 11LG 31 02968896 1 PLASTIC TIE, ORANGE, 11LG

02968874 1 MOTOR PRESSURE HOSE (RED)

02969463 1 MOTOR RETURN HOSE (ORANGE)

02968877 1 DOOR BASE HOSE (YELLOW/WHITE)

02968878 1 DOOR ROD HOSE (YELLOW)

02981844 1 SWIVEL ROD HOSE (GREEN)

02981845 1 SWIVEL BASE HOSE (GREEN/WHITE)

50 IN ROTARY - BLADE BAR HEAD SUB-ASY (SOLID MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 00015800 34 LOCKNUT TLM 3/8 NC PLC 2 02891800 4 HHCS 1/2 NC 1-3/4 PL8 3 00019600 4 LOCKWASHER 1/2 HEAVY 4 02982907 2 SKID SHOE 5 02981411 1 WELDMENT, DECK 50" HEAD 6 02961038 1 GASKET 7 02982906 1 ASY, BLADE BAR W/BLADES 8 02964861 4 SHCS 3/4 NC 4" LG PL8 9 15B600 14 WASHER 3/8 SAE P 10 00003901 4 LOCKWASHER 3/4 HEAVY 11 00059700 14 FSCS 3/8 NC X 1-1/4 12 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 13 03200269 8 HHCS 3/4 NC 3 PL8 14 02963645 8 HHCS 3/4 NC 1-3/4 PL8 15 00037200 16 NUT 3/4 NC LOCKNUT 16 5312316 16 FLATWASHER 3/4 HARDENED 17 02986200 1 WELDMENT, HITCH POST 18 02989904 1 HYD MOTOR - CAST IRON SPLINED 19 00749101 2 SPLIT FLANGE KIT #24 20 00751842 1 ADP HYD ELBOW 24FL - 16MJ - 90 21 00749104 1 ADP HYD ELBOW 24FL - 16MJ - 45 22 02958858 1 #16MJ-16FJ TUBE 90°

50 IN ROTARY - BLADE BAR HEAD SUB-ASY (SWIVEL MNT)

Continued... ITEM PART NO. QTY. DESCRIPTION

1 00015800 20 LOCKNUT TLM 3/8 NC PLC 2 02963646 3 HHCS 3/4 NC 2-1/2 PL8 3 00037200 18 NUT 3/4 NC LOCKNUT 4 02891800 4 HHCS 1/2 NC 1-3/4 PL8 5 00019600 4 LOCKWASHER 1/2 HEAVY 6 02982907 2 SKID SHOE 7 02981820 28 SHCS 1/2 NC X 1 1/2" LG PL8 8 02981318 1 SLEWING BEARING, 12 OD X 5.8 ID 9 02985319 1 WELDMENT, HITCH POST 10 02981411 1 WELDMENT, DECK 50" HEAD 11 02961038 1 GASKET 12 02982906 1 ASY, BLADE BAR W/BLADES 13 02981752 1 PLATE, HITCH POST BOTTOM, MAVERICK 14 02964861 4 SHCS 3/4 NC 4" LG PL8 15 15B600 14 WASHER 3/8 SAE P 16 00003901 4 LOCKWASHER 3/4 HEAVY 17 00059700 14 FSCS 3/8 NC X 1-1/4 18 02968859A 1 ASSEMBLY, SPINDLE HOUSING-SPLINED 19 02963645 6 HHCS 3/4 NC 1-3/4 PL8 20 5312316 18 FLATWASHER 3/4 HARDENED 21 03200269 8 HHCS 3/4 NC 3 PL8 22 02989904 1 HYD MOTOR - CAST IRON SPLINED 23 00749101 2 SPLIT FLANGE KIT #24 24 00751842 1 ADP HYD ELBOW 24FL - 16MJ - 90 25 00749104 1 ADP HYD ELBOW 24FL - 16MJ - 45 26 02984002 1 WLDMNT, STOP, SWIVEL 27 02958858 1 #16MJ-16FJ TUBE 90°

50 IN ROTARY - BLADE PAN HEAD ASY (SOLID MNT)

+ 144 hidden pages